Nady Audio GTA-1260 Bedienungsanleitung

GTA-1260

Classic Tube AMP with Reverb

OWNER’S MANUAL

GUITAR AMPLIFIER

GTA-1260

Classic Tube AMP with Reverb

Congratulations on your choice of guitar amplifier —

you have purchased one of the finest guitar amplifiers

on the market today. This unit was developed using the

expertise of professional sound engineers and working

musicians. You will find that your new NADY AUDIO

GTA-1260 has superior performance and greater

flexibility than any other guitar amplifiers in its price

range. Please read this manual carefully to get the

most out of your new unit.

Thanks for selecting NADY AUDIO as your choice in

guitar amplifier.

Date of Purchase

Dealer’s Name

City

State

Zip

Model #

Serial #

CONTENTS

FEATURES

FEATURES ................................................................................2

WARNING ..................................................................................3

INSTALLATION ..........................................................................4

LEGAL INFORMATION..............................................................4

FRONT CONTROL AND CONNECTORS ................................5

REAR CONTROL AND CONNECTORS ..................................6

SPECIFICATIONS ......................................................................7

•All-tube design featuring two 6L6GC power and three

12AX7A preamp tubes

•60W RMS output

•12”Nady PowerDrive™speaker by Celestion

•Full complement of controls for total volume, tone

shaping and tonal definition, including 3-way overdrive

gain switch, volume, master, treble, mid, bass and

presence controls

•Spring reverb with adjustable control and switchable with

optional FS-1 footswitch

•Classic retro look with attractive wood grain cabinet

finish

•Classic tube type tone controls

WARNING

IMPORTANT SAFETY INSTRUCTIONS

When using this electronic device, basic precautions should always be taken, including the following:

1. Read all instructions before using the product.

2. Do not use this product near water (e.g., near a bathtub, washbowl, kitchen sink, in a wet basement, or near a

swimming pool, etc.).

3. This product should be used only with a cart or stand that will keep it level and stable and prevent wobbling.

4. This product, in combination with headphones or speakers, may be capable of producing sound levels that

could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a

level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an

audiologist.

5. The product should be positioned so that proper ventilation is maintained.

6. The product should be located away from heat sources such as radiators, heat vents, or other devices

(including amplifiers) that produce heat.

7. The product should be connected to a power supply only of the type described in the operating instructions or

as marked on the product. Replace the fuse only with one of the specified type, size, and correct rating.

8. The power supply cord should: (1) be undamaged, (2) never share an outlet or extension cord with other

devices so that the outlet’s or extension cord’s power rating is exceeded, and (3) never be left plugged into

the outlet when not being used for a long period of time.

9. Care should be taken so that objects do not fall into, and liquids are not spilled through, the enclosure’s

openings.

10. The product should be serviced by qualified service personnel if:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen into, or liquid has been spilled onto the product.

C. The product has been exposed to rain.

D. The product does not appear to operate normally or exhibits a marked change in performance.

E. The product has been dropped, or the enclosure damaged.

11. Do not attempt to service the product beyond what is described in the user maintenance instructions. All

other servicing should be referred to qualified service personnel.

ATTENTION

: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

An equilateral triangle enclosing a lightening flash/arrowhead symbol is

intended to alert the user to the presence of uninsulated “dangerous

voltage”within the product’s enclosure which may be of sufficient

magnitude to constitute a risk of electric shock.

An equilateral triangle enclosing an exclamation point is intended to alert

the user to the presence of important operating and service instructions in

the literature enclosed with this unit.

INSTALLATION

To ensure years of enjoyment from your NADY AUDIO GTA-1260, please read and understand this manual thoroughly before

using the unit.

INSPECTION

Your NADY AUDIO GTA-1260 was carefully packed at the factory in packaging designed to protect the units in shipment.

Before installing and using your unit, carefully examine the packaging and all contents for any signs of physical damage

that may have occurred in transit.

[Please note: Nady Systems is not responsible for shipping damage. If your unit is damaged, do not return to Nady, but

notify your dealer and the shipping company (if shipped to you) immediately to make a claim. Such claims must be made

by the consignee in a timely manner.]

CONTENTS

•Instruction manual

•GTA-1260 (verify that the unit’s serial number is same as shown on shipping carton)

•AC Power cord

•Warranty Card

POWER CONNECTION

The GTA-1260 has an internal power supply and is designed to operate from an external AC source. Power requirements

for electrical equipment differ from area to area. Be sure to confirm that the voltage selected by the voltage selector switch

on the back panel is proper for your area (120VAC/60 Hz or 230VAC/50Hz) per the information below:

Europe (except UK): 230V, 50Hz

UK and Australia: 240V, 50Hz

USA and Canada: 120V, 60 Hz

For other areas, please check with local authorities.When ready to operate, plug the AC cord into the power source. Make

sure that the unit is turned off before connecting to the AC power source to avoid possible loud transients that can

damage your speakers or your ears, especially when monitoring with headphones.

NOTICE

The information in this document is subject to change, as the Company may make changes to product in order to improve

reliability, design, or function, without prior written notice. No part of this manual may be reproduced or transmitted in any form

or by any means without the written permission of the company.

IN NO EVENT WILL THE COMPANY BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES,

WHETHER ARISING DIRECTLY OR INDIRECTLY, SUCH AS LOSS OF PROFIT OR GOOD WILL, THAT MAY BE

SUFFERED IN CONNECTION WITH THE PURCHASE OF THIS PRODUCT OR FROM THE BREACH OF ANY

REPRESENTATION OR WARRANTY.

LICENSE

The Company grants the customer a non-exclusive, non-transferable license to use the software, if any, accompanying this

product for internal use on a single computer system. The end user may make a single copy of the software solely for backup

purposes; otherwise, no copies may be made of the software or any part thereof. No other license of any kind is granted to

any part of the product or any of the intellectual property therein.

LEGAL INFORMATION

FRONT CONTROLS AND CONNECTIONS

(1)

1. POWER SWITCH

This switch turns the main power on and off. Flipping the

toggle switch up to the ON+ position will turn on the amp

“in phase”with the main AC line voltage. Flipping the

switch down to the ON- position will reverse the polarity.

In some cases, AC hum (caused by ground loops) can be

reduced by reversing the polarity. Select the On position

which has the least amount of AC hum.

2. POWER INDICATOR LIGHT

Lights when the unit is powered on.

3. STANDBY SWITCH

Flipping this toggle switch to ON/OFF (STBY) will

respectively enable/disable the audio to the amplifier and

the outputs. This allows for proper warm-up of the tubes

before applying signal to them, and allows the amp to stay

warm when not in immediate use. To extend the life of

the tubes, always turn the Main Power Switch on first, for

1-2 minutes, before flipping ON the Standby Switch.

4. INPUT JACK

Input for instrument outputs —guitar, keyboard, high-

output mics for harmonicas, and other effects devices.

5. DISTORTION SELECTOR

This three-way switch selects the input sensitivity and

amount of overdrive distortion. Position 1 offers the

cleanest signal with least amount of distortion. Position 3

has the maximum amount of distortion.

Note: The VOLUME and MASTER controls also affect

the final signal level and the amount of distortion.

• For cleanest operation (least distortion) adjust the

VOLUME to a very low setting, the MASTER to

maximum, and the DISTORTION to Position 1.

• For medium distortion ( or crunch) adjust the

VOLUME to past the mid position, the MASTER to

mid, and the DISTORTION to Position 2.

• For maximum distortion adjust the VOLUME to

maximum, the MASTER to a very low setting, and

the DISTORTION to Position 3.

6. VOLUME CONTROL

This adjusts the level of the input signal to the amp.

Increasing this level will create distortion dependent on

the DISTORTION setting.

7. MASTER VOLUME CONTROL

Adjusts overall loudness of the amp.

8. TREBLE CONTROL

Adjusts the level of treble/Hi frequencies.

9. MID CONTROL

Adjusts the level of mid-range frequencies.

10. BASS CONTROL

Adjusts the level of bass frequencies.

11. PRESENCE CONTROL

Adjusts the high overtones, texture, and feel of the amp.

12. REVERB CONTROL

Adjusts the level of reverb mixed with the dry signal.

(2)(3)

(4) (5) (6) (7) (8) (9) (10) (11) (12)

REAR CONTROLS AND CONNECTIONS

1. POWER CONNECTION

A standard IEC AC power socket for connecting to the

main AC supply. The IEC power socket has an integral

fuse holder that takes a 20mm fuse.

NOTE:

• Always replace a blown fuse with the same type as

specified on the rear panel and under

SPECIFICATIONS (pg. 7) for the AC voltage being

used to power the amp

• Before you connect your GTA-1260 to the AC,

please make sure that your local voltage matches

the voltage required by the unit!

• Do not remove the center ground conductor.

2. VOLTAGE SELECTOR SWITCH

For selecting the proper voltage (115/230VAC) to match

the power supply in your area.

3. REVERB FOOTSWITCH JACK

For connecting an optional external footswitch to turn the

reverb on and off. See your dealer for ordering the Nady

FS-1 footswitch, or order directly from Nady with the

included ordering form.

If reverb footswitch jack is not used for switching. a pure

reverb line level signal is present at the jack. This may be

used for stereo effects with an outboard amp and speaker

or plugged into mixing consoles and tape machines for

recording. The output at F.S. Jack is sleeve GND, TIP

HOT +

4. SPEAKER JACK

This jack is connected to the internal speaker using a “L”

shaped plug and speaker cable. The internal speaker can

be disconnected if you wish to only use external speakers.

5. EXTERNAL SPEAKER

Jack for connecting external speakers. For optimum output

power, these should be 8Ωminimum.

6. LINE OUT

This line level output signal is derived from the output of

the power amp to incorporate all the characteristics, color

and tonal response of the output tubes. This signal can be

input into any device, such as an audio mixer or another

amplifier, and can be useful in many lives sound or

recording applications.

(1) (2) (3) (5) (6)

(4)

SPECIFICATIONS

The specifications above are correct at the time of printing of this manual. For improvement purposes, all specifications for this unit, including design

and appearance, are subject to change without prior notice.

Power Amp Section ..............................................................................................................................Tubes: 2 ea 6L6GC

Power Output........................................................................................60 Watts @ 8Ω5% THD; 40 Watts @ 4Ω5% THD

Speaker ....................................................................................................Nady PowerDrive™PD-12i by Celestion, 12”8Ω

Preamp Section....................................................................................................................................Tubes: 3 ea 12AX7A

Input Imp. .................................................................................................................................................................. 200KΩ

Input Sens. .................................................................................................. Max clean 800Mv 1KHz; Max dist. 8Mv. 1KHz

Line Out Inp. ................................................................................................................................................................ 600Ω

Line Out Level.................................................................................................................................................... 1V Nominal

Power Requirements ............................................................................................................ 115VAC/60Hz; 230VAC/50Hz

Fuse ............................................................................ For 115 VAC: 3 AMP S.B. 250V; For 230 VAC: 1.5 AMP S.B. 250V

Dimension .......................................................................................................... 18.3”x 9”x 17.5”(46.5 x 22.9 x 44.5 cm)

Weight ...................................................................................................................................................... 45.6 lbs. (20.7 kg)

TUBE REPLACEMENT

Preamp Tubes 12AX7A —No adjustment required