Napoleon B52NL-1 Bedienungsanleitung

FRENCH PG. 13

W415-2745 / A / 11.04.19

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

- Installation and service must be

performed by a qualiﬁed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

B52NL-1

B52PL-1

INSTALLATION AND

OPERATION MANUAL

HDX52-2

Burner Assembly,

Log Set Conﬁguration

A. Remove the door

(refer to installation

instructions). Remove

the 8 securing

screws and lift the

plate up and out of

the appliance. The

gasket will need to be

replaced if damaged.

A. Attach the burner assembly to the ﬁrebox

base with the 4 screws supplied.

This burner and log assembly are approved for use in the HDX52-1 gas appliance only. They are not approved for

use as a stand alone appliance or in conjunction with any other appliance.

1.0 general information

2.0 installation

2.1 access panel

2.2 burner assembly

1.0 general information 2

2.0 installation 2

2.1 access panel 2

2.2 burner assembly 2

2.3 bulkheads 3

2.4 hearth panel installation 4

2.5 hearth log & log placement 5

2.6 charcoal lumps 7

2.7 charcoal embers 7

2.8 vermiculite 7

2.9 glowing embers 7

3.0 adjustment 8

3.1 ﬂame characteristics 8

3.2 venturi adjustment 8

4.0 replacement parts 9

4.1 overview 10

4.2 B52NL-1 log burner 11

INSIDE APPLIANCE OUTSIDE APPLIANCE

W415-2745 / A / 11.04.19

table of contents

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial are denoted by a vertical line in the margin.

note:

A. Connect the main burner gas ﬂex line and the

pilot line to the gas ﬁttings on the bulkheads

located under the valve access opening. Care

must be taken to ensure the pilot line is not

damaged and gas tight connections are made.

B. Connect the pilot electrode lead to the

bulkhead, matching the 3/16" ﬂag with the

3/16" bulkhead spade. Do the same with

the 1/4” spark lead, matching it with the 1/4”

bulkhead spade.

C. Check for gas leaks by brushing on a soap

and water solution. Do not use open ﬂame.

D. After leak test has been performed, re-install

access panel with gasket.

2.3 bulkheads

note:

Bulkhead covers need to be removed before

beginning installation.

note:

Ensure the venturi tube is over the oriﬁce before

lighting.

Ori ce

Venturi

Tube

Pilot

Electrode

Lead

Bulkhead

Main

Burner Gas

Connection

Pilot Tube

Gas Connection

W415-2745 / A / 11.04.19 3

installation

Hearth ﬂoor panels are shipped separately from the appliance and are included with the mandatory brick panel kits.

As the panels are made with brittle material, care must be taken not to bend or force them into place. When shipped,

the hearth panels are varying shades of Sandstone / New Port. During initial use, the panels will darken in colour;

however with time and use, they will lighten permanently.

2.4 hearth panel installation

note:

It is recommended to remove the grate assembly prior to panel installation.

note:

Install hearth ﬂoor panels according to the installation leaﬂet.

W415-2745 / A / 11.04.19

installation

2.5 hearth log & log placement

PHAZERTM logs and glowing embers are exclusive to Napoleon. They provide a realistic glowing effect that is unique

in every installation. Take time to carefully position the glowing embers for a maximum glowing effect. Log colours

may vary. As a result of the heat-activated curing process, the colours will become more uniform during the appli-

ance's initial use as pigments burn in.

note:

All logs are stamped with a part number.

A. Align the hole in the bottom of the rear

left log (marked #1) with the stud on the

left of the burner. Ensure no ports are

covered.

B. Align the hole in the bottom of the rear

right log (marked #2) with the stud on the

right of the burner. Ensure no ports are

covered.

C. Place the front left log (marked #3) over

the front left part of the burner so that

the notch is around the center grate

post. Ensure no ports are covered.

D. Place the front right log (marked #4) over

the front right part of the burner so that

the notch is around the center grate post.

Ensure no ports are covered.

E. Align the slots in the bottom left rear log

(W135-0566) with the left and center

tabs of the rear log support.

F. Place the bottom right rear log (W135-

0567) onto the right tab of the rear log

support.

W415-2745 / A / 11.04.19 5

installation

G. Place the locating block (W135-0573)

into the hollow of the left and right

bottom rear logs as shown.

H. Place the top rear log (W135-0565) over

the locating block.

I. Place the notch of the left log (W135-

0568) over the second-from-the-left

grate post.

J. Place the notch of the right log (W135-

0569) over the second-from-the-right

grate post.

K. Place the notch in the left crossover log

(W135-0570) over the left locating stud in

the top rear log. Let it rest in the notch of

the left log.

L. Place the notch in the right crossover log

(W135-0571) over the right locating stud

in the top rear log. Let it rest in the notch

of the right log.

W415-2745 / A / 11.04.19

installation

2.6 charcoal lumps

2.7 charcoal embers

2.9 glowing embers

2.8 vermiculite

Place the lumps in front of the logs in a realistic manner taking care not to block or close off any of the burner ports.

!WARNING

• Do not block or close off the burner ports. Blocked ports can cause an incorrect ﬂame pattern, carbon

deposits and delayed ignition.

• When supplied, charcoal embers, charcoal lumps and vermiculite are not to be placed on the burner.

Randomly place the charcoal embers along the front and sides of the log support in a realistic manner.

Fine dust found in the bottom of the bag should not be used.

!WARNING

• Do not block or close off the burner ports. Blocked ports can cause an incorrect ﬂame pattern, carbon

deposits and delayed ignition.

• When supplied, charcoal embers, charcoal lumps and vermiculite are not to be placed on the burner.

note:

Charcoal embers are not to be placed on the burner.

Sprinkle vermiculite around the charcoal embers.

!WARNING

• Do not block or close off the burner ports. Blocked ports can cause an incorrect ﬂame pattern, carbon

deposits and delayed ignition.

• When supplied, charcoal embers, charcoal lumps and vermiculite are not to be placed on the burner.

note:

Vermiculite is not to be placed on the burner.

ear the embers into pieces and loosely layer above the burner ports covering the burner area. Care should be

taken to shred the embers into thin, small irregular pieces as only the exposed edges of the ﬁbre hairs will glow.

The ember material will only glow when exposed to direct ﬂame; however, care should be taken to not

lock off the burner ports.

Blocked burner ports can cause an incorrect ﬂame pattern, carbon deposits and delayed ignition. PHAZER™

logs glow when exposed to direct ﬂame. Use only certiﬁed “glowing embers” and PHAZER™logs available from

your local authorized dealer / distributor.

!WARNING

• Completely blocking the burner ports can cause an incorrect ﬂame pattern, carbon deposits and delayed

ignition.

W415-2745 / A / 11.04.19 7

installation

3.0 adjustment

3.1 ﬂame characteristics

3.2 venturi adjustment

AIR SHUTTER OPENINGS

(BOTH BURNERS)

NG 3/8” (9.5mm)

P 7/16” (11.1mm)

It’s important to periodically perform a visual check of

the pilot and burner ﬂames. Compare them to the

illustration provided. If any ﬂames appear abnormal,

call a service person.

Flame must envelop

upper

3/8" to 1/2"

(12.7mm - 9.5mm) of

Flame sensor

3/8” - 1/2”

(9.5mm - 12.7mm)

This appliance has an air shutter that has been factory set open according to

the chart below:

Regardless of venturi orientation, closing the air shutter will cause a more

yellow ﬂame, but can lead to carbonization. Opening the air shutter will cause

a more blue ﬂame, but can cause ﬂame lifting from the burner ports. The ﬂame

may not appear yellow immediately; allow 15 to 30 minutes for the ﬁnal ﬂame

colour to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED

INSTALLER.

AIR

SHUTTER

OPENING

VENTURI

BURNER

ORIFICE

It is important that the oriﬁce is securely inserted into the venturi.

note:

W415-2745 / A / 11.04.19

W415-2745 / A / 11.04.19 9

4.0 replacement parts

!WARNING

• Failure to position the parts in accordance with this manual or failure to use only parts speciﬁcally approved

with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can

be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the

claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

Parts, part numbers, and availability are subject to change without notice.

Parts identiﬁed as stocked will be delivered within 2 to 5 business days for most delivery

destinations.

Parts not identiﬁed as stocked will be delivered within a 2 to 4 week period, for most cases.

Parts identiﬁed as ‘SO’ are special order and can take up to 90 days for delivery.

4.1 overview

W415-2745 / A / 11.04.19

replacement parts

Items may not appear exactly as illustrated.

Ref. Stocked

Log burner assembly

B52NL/PL-1

W135-0568 Left log (GL-695)

W135-0565

W135-0566

W135-0567

W135-0569

W135-0570

W135-0571

For replacement parts,

see “B52NL-1 log

burner” section.

W585-0834 Vent pipe shield

GL-695

Top rear log (GL-695)

Bottom left rear log (GL-695)

Right crossover log (GL-695)

Bottom right rear log (GL-695)

Right log (GL-695)

Left crossover log (GL-695)

W135-0585

W135-0584

W135-0586

Rear left, charcoal (GL-695)

Rear right, charcoal (GL-695)

Front left, charcoal (GL-695)

W135-0583

16 Front right, charcoal (GL-695)

GL-695

13 14

12 W135-0573 Block log (GL-695)

11 W550-0001 Charcoal embers (GL-695)

10 W361-0016 Glowing embers (GL-695)

Yes

tockedPart Number Description

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Napoleon Kaminzubehör Handbücher

Napoleon

Napoleon GD851KT Bedienungsanleitung

Napoleon

Napoleon CFF Bedienungsanleitung

Napoleon

Napoleon NEFI27H-CTC Bedienungsanleitung

Napoleon

Napoleon DBPAX36 Bedienungsanleitung

Napoleon

Napoleon ZEX42CH Bedienungsanleitung

Napoleon

Napoleon B19NL-2 Bedienungsanleitung

Napoleon

Napoleon B36NTREA-1 Service-Handbuch

Napoleon

Napoleon BTAX36 Bedienungsanleitung

Napoleon

Napoleon Allure Vertical Series Bedienungsanleitung

Napoleon

Napoleon DBPEX36 Bedienungsanleitung

Napoleon

Napoleon high country nz3000h Bedienungsanleitung

Napoleon

Napoleon LHD45 Bedienungsanleitung

Napoleon

Napoleon LHD45 Bedienungsanleitung

Napoleon

Napoleon BKGDIX3 Bedienungsanleitung

Napoleon

Napoleon Woodland HEFI27H Bedienungsanleitung

Napoleon

Napoleon D42 Bedienungsanleitung

Napoleon

Napoleon PRP81-1 Bedienungsanleitung

Napoleon

Napoleon NCEX36 Bedienungsanleitung

Napoleon

Napoleon DBPO36 Bedienungsanleitung

Napoleon

Napoleon MKE50 Bedienungsanleitung

Napoleon

Napoleon GD861KT Bedienungsanleitung

Napoleon

Napoleon FPGI30 Bedienungsanleitung

Napoleon

Napoleon DBPB36 Bedienungsanleitung

Napoleon

Napoleon BHD4 PENINSULA Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung