Napoleon B52NTL Bedienungsanleitung

FRENCH PG. 13

W415-2746 / A / 11.04.19

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

- Installation and service must be

performed by a qualiﬁed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

B52NTL

B52PTL

INSTALLATION AND

OPERATION MANUAL

HDX52-2

Burner Assembly,

Oak Log Set Conﬁguration

A. Remove the door,

refer to installation

instructions.

Remove the 8

securing screws

and lift the plate

up and out of

the appliance.

Gasket will need

to be replaced if

damaged.

A. Attach the burner assembly to the ﬁrebox

base with the 2 screws supplied.

This burner and log assembly are approved for use in the HDX52 gas appliance only. They are not approved for

use as a stand alone appliance or in conjunction with any other appliance.

1.0 general information

2.0 installation

2.1 access panel

2.2 burner assembly

1.0 general information 2

2.0 installation 2

2.1 access panel 2

2.2 burner assembly 2

2.3 bulkheads 3

2.4 hearth panel installation 4

2.5 hearth log & log placement 5

2.6 charcoal lumps 7

2.7 charcoal embers 7

2.8 vermiculite 7

2.9 glowing embers 7

3.0 adjustment 8

3.1 ﬂame characteristics 8

3.2 venturi adjustment 8

4.0 replacement parts 9

4.1 log overview 9

4.2 log burner assembly (NG) 10

4.3 log burner assembly (P) 11

INSIDE APPLIANCE

OUTSIDE APPLIANCE

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial are denoted by a vertical line in the margin.

note:

W415-2746 / A / 11.04.19

table of contents

A. Connect the main burner gas ﬂex line and the

pilot line to the gas ﬁttings on the bulkheads

located under the valve access opening.Care

must be taken to ensure the pilot line isn’t

damaged and ensuring gas tight connections

are made.

2.3 bulkheads

B. Connect the pilot electrode lead to the

bulkhead matching the 3/16" ﬂag with the

3/16" bulkhead spade. Do the same with the

1/4” spark lead to the 1/4” bulkhead spade.

C. Ensure the venturi tubes are over the oriﬁce

before lighting.

D. Check for gas leaks by brushing on a soap

and water solution. Do not use open ﬂame.

E. After leak test has been performed re-install

access panel with gasket.

note:

Bulkhead covers need to be removed before

beginning installation.

Main

Burner Gas

Connection

Pilot Tube

Gas Connection

Pilot

Electrode

Lead

Bulkhead

W415-2746 / A / 11.04.19 3

installation

Hearth ﬂoor panels are shipped separate from the appliance and are included with the mandatory brick panel kits.

Due to the brittle material of the panels, care must be taken not to bend or force them into place.

When shipped, the hearth panels range in varying shades of Sandstone / New Port. During initial use, the panels will

darken temporarily. The appearance of the panels will permanently lighten in color with use.

INSTALL HEARTH FLOOR PANELS ACCORDING TO THE INSTALLATION LEAFLET.

2.4 hearth panel installation

note:

It is recommended to remove the grate assembly prior to panel installation.

W415-2746 / A / 11.04.19

installation

2.5 hearth log & log placement

A. Align the 2 holes in the bottom of the

bottom rear log with the studs located on

the rear log support.

B. Align the 2 pins in the bottom of the top

rear log with the holes in the top of the

bottom rear log.

C. Align the 2 holes in the bottom in the

middle log with the studs located on the

front log support.

D. Align the hole in the rear left log with the

left pin of the top rear log.

E. Line the notches in the bottom of the

front right log with the 4th and 5th grate

posts. Make sure not to cover ports.

F. Line the notch in the front left log with the

front left corner of the burner.

W415-2746 / A / 11.04.19 5

installation

G. Align the 2 holes located in the bottom

of the front left crossover log with the 2

studs on the left hand side of the burner.

H. Align the 2 holes in the bottom of the

right middle log with the 2 studs on the

right hand side of the burner.

I. Place the top right log on the notches in

the bottom rear log and the front right log

pushing back against the rear panel.

J. Align the hole and the pin in the right

crossover log with the pin in the top rear

log and the hole in the top right log.

K. Place the notch in the front charcoal log

over the second grate post. Make sure

not to cover any ports.

L. Align the pin in the bottom of the middle

crossover with the hole in the middle of

the middle log resting it on the front left

crossover log.

W415-2746 / A / 11.04.19

installation

2.6 charcoal lumps

2.7 charcoal embers

2.8 vermiculite

2.9 glowing embers

Place the lumps in front of the logs in a realistic manner taking care not to block or close off any of the burner ports.

!WARNING

• Do not block or close off the burner ports. Blocked ports can cause an incorrect ﬂame pattern, carbon

deposits and delayed ignition.

• When supplied, charcoal embers, charcoal lumps and vermiculite are not to be placed on the burner.

Randomly place the charcoal embers along the front and sides of the log support in a realistic manner.

Fine dust found in the bottom of the bag should not be used.

!WARNING

• Do not block or close off the burner ports. Blocked ports can cause an incorrect ﬂame pattern, carbon

deposits and delayed ignition.

• When supplied, charcoal embers, charcoal lumps and vermiculite are not to be placed on the burner.

note:

Charcoal embers are not to be placed on the burner.

Sprinkle vermiculite around the charcoal embers.

!WARNING

• Do not block or close off the burner ports. Blocked ports can cause an incorrect ﬂame pattern, carbon

deposits and delayed ignition.

• When supplied, charcoal embers, charcoal lumps and vermiculite are not to be placed on the burner.

note:

Vermiculite is not to be placed on the burner.

ear the embers into pieces and loosely layer above the burner ports covering the burner area. Care should be

taken to shred the embers into thin, small irregular pieces as only the exposed edges of the ﬁbre hairs will glow.

The ember material will only glow when exposed to direct ﬂame; however, care should be taken to not

lock off the burner ports.

Blocked burner ports can cause an incorrect ﬂame pattern, carbon deposits and delayed ignition. PHAZER™

logs glow when exposed to direct ﬂame. Use only certiﬁed “glowing embers” and PHAZER™logs available from

your local authorized dealer / distributor.

!WARNING

• Completely blocking the burner ports can cause an incorrect ﬂame pattern, carbon deposits and delayed

ignition.

W415-2746 / A / 11.04.19 7

installation

Air Shutter Openings both Burners

P F 7/16" R 1/4”

NG F 1/16" R 1/16”

3.0 adjustment

3.1 ﬂame characteristics

It’s important to periodically perform a visual check of

the pilot and burner ﬂames. Compare them to the

illustration provided. If any ﬂames appear abnormal,

call a service person.

Flame must envelop

upper

3/8" to 1/2"

(12.7mm - 9.5mm) of

Flame sensor

3/8” - 1/2”

(9.5mm - 12.7mm)

3.2 venturi adjustment

This appliance has an air shutter that has been factory set open according to

the chart below:

Regardless of venturi orientation, closing the air shutter will cause a more

yellow ﬂame, but can lead to carbonization. Opening the air shutter will cause

a more blue ﬂame, but can cause ﬂame lifting from the burner ports. The ﬂame

may not appear yellow immediately; allow 15 to 30 minutes for the ﬁnal ﬂame

colour to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED

INSTALLER.

AIR

SHUTTER

OPENING

VENTURI

BURNER

ORIFICE

It is important that the oriﬁce is securely inserted into the venturi.

note:

W415-2746 / A / 11.04.19

4.1 log overview

W415-2746 / A / 11.04.19 9

4.0 replacement parts

!WARNING

• Failure to position the parts in accordance with this manual or failure to use only parts speciﬁcally approved

with this appliance may result in property damage or personal injury.

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can

be ordered through your Authorized dealer / distributor.

For warranty replacement parts, a photocopy of the original invoice will be required to honour the

claim.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

Parts, part numbers, and availability are subject to change without notice.

Parts identiﬁed as stocked will be delivered within 2 to 5 business days for most delivery

destinations.

Parts not identiﬁed as stocked will be delivered within a 2 to 4 week period, for most cases.

Parts identiﬁed as ‘SO’ are special order and can take up to 90 days for delivery.

W135-0630-SER

W135-0631-SER

W135-0634-SER

W135-0635-SER

W135-0632-SER

W135-0633-SER

W135-0636-SER

W135-0638-SER

W135-0639-SER

W135-0637-SER

W135-0640-SER

W135-0629-SER

Items may not appear exactly as illustrated.

Ref. Part Number

Log, rear top

Log, middle

Log, front right

Log, front left

Log, front left crossover

210

Log, rear left

Log, right middle

Log, right top

Log, right crossover

Log, front charcoal

Log, middle crossover

811

Log, rear bottom

Description Stocked

Ref.

art

escr

tocked

4.2 log burner assembly (NG)

W415-2746 / A / 11.04.19

replacement parts

W010-3822-SER

Assembly, grate

Yes

W100-0205-SER

Assembly, complete

W010-3818-SER

Assembly, pilot high temp. 3-way

W080-1645-SER

Bracket, pilot shield

W010-3849-SER

Assembly, tube burner weldement

N255-0002

-SER

Fitting, union bulkhead 3/8 MF to 3/8MF

W432-0540-SER

Manifold

W456-0031-SER

Front burner oriﬁce

W456-0026-SER

Rear burner oriﬁce

Ref. Part Number

Items may not appear exactly as illustrated.

Description Stocked

art

escri

tion

tocke

Yes

Andere Handbücher für B52NTL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Napoleon Kaminzubehör Handbücher

Napoleon

Napoleon GS831C Bedienungsanleitung

Napoleon

Napoleon GD849KT Bedienungsanleitung

Napoleon

Napoleon MKRY Bedienungsanleitung

Napoleon

Napoleon MKRY3 Bedienungsanleitung

Napoleon

Napoleon HDX35 Bedienungsanleitung

Napoleon

Napoleon Ascent DBPX70 Bedienungsanleitung

Napoleon

Napoleon EPK1 Bedienungsanleitung

Napoleon

Napoleon GS67-1 Bedienungsanleitung

Napoleon

Napoleon high country nz3000h Bedienungsanleitung

Napoleon

Napoleon RCHS20 Bedienungsanleitung

Napoleon

Napoleon PRPAX36 Bedienungsanleitung

Napoleon

Napoleon RAK30 Bedienungsanleitung

Napoleon

Napoleon SLF Bedienungsanleitung

Napoleon

Napoleon DBPO36 Bedienungsanleitung

Napoleon

Napoleon S50 Bedienungsanleitung

Napoleon

Napoleon Wolf Steel Silhouette Bedienungsanleitung

Napoleon

Napoleon B19NL-2 Bedienungsanleitung

Napoleon

Napoleon LFG45 Bedienungsanleitung

Napoleon

Napoleon GA-566 Bedienungsanleitung

Napoleon

Napoleon NEFTK30BK-3828 Bedienungsanleitung

Napoleon

Napoleon LHD45 Bedienungsanleitung

Napoleon

Napoleon FF38 Bedienungsanleitung

Napoleon

Napoleon PRP81-1 Bedienungsanleitung

Napoleon

Napoleon GX725WI Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung