Napoleon SDO1000 Montageanleitung

Sectional and Tilting Door Opener

Installation Instructions and User Guide

SDO 800

SDO1000

S/N

WARNING

Please read the manual carefully before installation and use. The installation of your

new door opener must be carried out by a technically qualified or licensed person.

Attempting to install or repair the door opener without suitable technical qualification

may result in severe personal injury, death and / or property damage.

CONTENTS

Important Safety Recommendations...…………………………….……………………………..1-2

Basic function introduction……………………………………………………………………….....2

Special function introduction………….……………………..……………………………………..2

Installation (aluminum track)………………………………………….…………………………..3-4

Installation (steel track)………………………………………….…………………………….…….5

Installation recommendations……………………………………………………………………..6

Basic function setting and applying………………………………………………………………7-8

Special function introduction and application………………………………………….……….9-10

PCB structure………………..…………………………………………………………..……….... 10

Aluminum, steel & sectional steel accessory list…………………..…………………….……...11

Manual disengagement…………………………………………………………………………….12

Maintenance………………………………………………………………………………………...12

Technical specifications…………………………………………………………………………….13

Final note….………………………………………………………………………………………...13

Important information for the user………………………………………………………………...13

Important safety recommendations

FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY

RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE.

1. PLEASE READ CAREFULLY AND ADHERE TO ALL SAFETY AND INSTALLATION

RECOMMENDATIONS.

2. The opener is designed and manufactured tomeet local regulations. The installer must be

familiar with local regulations required in respect of the installation of the opener.

3. Unqualified personnel or those persons who do not know the occupational health and

safety standards being applicable to automatic gates and other doors, must in no

circumstances carry out installations or implement systems.

4. Persons who install or service the equipment without observing all the applicable safety

standards will be responsible for any damage, injury, cost, expense or claim whatsoever

any person suffered as a result of failure to install the system correctly and in accordance

with the relevant safety standards and installation manual whether directly or indirectly.

5. For additional safety we strongly recommend the inclusion of Photo Beam. Although the

opener incorporates a pressure sensitive Safety Obstruction Force system the addition of

Photo Beam will greatly enhance the operating safety of an automatic garage door and

provide additional peace of mind.

6. Make sure that the garage door is fully open & stationary before driving in or out of the

garage.

7. Make sure the garage door is fully closed & stationary before leaving.

8. Keep hands and loose clothing off the opener and garage door all the time.

9. The Safety Obstruction System is designed to work on STATIONARY objects only.

Serious personal injury, death and / or property damage may occur if the garage door

comes into contact with a moving object

10. This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety. Children should be supervised

to ensure that they do not play with the appliance.

11. Waste electrical products should not be disposed of with household waste.

Please recycle where facilities exist. Check with your local authority or retailer for

recycling advice.

12. If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualified persons in order to avoid a hazard.

- WARNING: Important safety instructions. It is important for the safety of persons to

follow all instructions. Save these instructions.

- Do not allow children to play with door controls. Keep remote controls away from

children.

- Watch the moving door and keep people away until the door is completely opened

or closed.

- Take care when operating the manual release since an open door may fall rapidly

due to weak or broken springs, or being out of balance.

- Frequently examine the installation, in particular check cables, springs and

mountings for signs of wear, damage or imbalance. Do not use if repair or

adjustment is needed since a fault in the installation or an incorrectly balanced door

may cause injury.

- Each month check that the drive reverses when the door contacts a 50 mm high

object placed on the floor. Adjust if necessary and recheck since an incorrect

adjustment may present a hazard, for drives incorporating an entrapment

protection system depending on contact with the bottom edge of the door.

- Details on how to use the manual release.

- Information concerning the adjustment of the door and drive.

- Disconnect the supply when cleaning or carrying out other maintenance.

- The installation instructions shall include details for the installation of the drive and

its associated components.

Basic function introduction

1. Soft start, soft stop Minimize start-up load on garage door opener and garage door

2. Opening & closing force self-learning

3. Overloading force detecting, the door will reverse more than 15 cm automatically when

it is overloaded when closing.

4. Safety resistance adjustable, with a wide range, sensitive and reliable.

5. L.E.D light for caution

6. Wall switch interface available.

7. Photo beam, the door will change to open when obstruction is detected while closing.

8. Low-voltage protection, the process will not perform any action of opening and closing

when voltage is too low, door panel and controller won’t be damaged.

9. We adopt rolling code transmitter, with billions of codes, won’t be coincident code or

pirated code.

10. Back up battery interface available, in case of power failure.

11. Keypad interface available.

12. With auto-closing feature.

13. Metal bottom plate, stronger and security.

14. O/S/C button B, make adjustment, maintenance and emergent opening or closing

convenient. (Below picture)

15. External fuse A. (Below picture)

Referring to Fig. 2 for recommended installation

1) Sectional door rail 5) O/S/C button

2) 24V DC flash light (optional part ) 6) Power socket

3) Wall switch(optional part ) 7) Door opener

4) Photo beam (RX/TX Type)

CHAIN SHUTTLE ASSEMBLY

As for the ease of the chain, it is delivered with the

chain and chain shuttle already assembled in the

track. If you need to assemble it yourself, connect

the chain shuttle to the chain with screw C tightened

firmly. Move shuttle B to half way along the rail

section; grease the chain and sprocket (Fig.3) with

a lithium type grease or equivalent. Do not use oil

type lubricants.

Fig. 6

Fig. 7

Before attaching the motor brackets

(E) (FIG 4) screw an inverted nut

(6mm) (D) on each stud then position

the brackets (E) on the studs and

secure them in-place using a second

6mm-nut and then lock the brackets to

the rail by tightening the inverted lock

nuts (D). Connect the opener edge (G)

to the doorframe or to the ceiling iron

angle (F) (Fig.5), maintaining a

minimum gap of 30mm from the top

panel’s maximum height (Fig. 6).

Check measurements for drilling insert

and lock the brackets F and fix the

opener to the ceiling with the correct

fixings (Fig. 7). Cut off any hanging

brackets excess.

Warning: Make sure the opener is

affixed to noggins in ceiling and not to

plasterboard. Failure to have a safe

and secure fixing will lead to opener

falling, and cause serious persons and

/or property damage.

Installation (steel track)

Fig. 1

1. Fixing the track bracket. Fixing the track bracket to the wall 2cm-15cm over the shaft or

intermediate bracket (depend on the actual installation space).

2. Fixing the steel track to the bracket with copper pin. (Fig. 1)

3. Fixing garage door opener to the track by U hanging bracket. It’s enough for 2 Nm

fastening force.

4. Fixing the opener on ceiling by iron angle. Notice: Make sure the track is horizontal and

vertical to the shaft. Make sure the connection of iron angle and ceiling is firm enough.

5. The connection of panel bracket and panel connector refers to the installation of aluminum

track. Fix the clutch cord.

6. Release the clutch, try to open and close the door by hand. Make sure there is no

resistance between door panel and track.

7. Connecting the opener with power and adjusting the operation.

Notice: Make sure the opener’s voltage is in accordance with the local voltage. Connect

the opener to a properly earthed power supply.

Installation recommendations

Remember there are specific standards that have to be strictly followed regarding the safety

rules of electrical installations and automatic gates and doors.

As for the legal requirements and standards that must be adhered to, please take notice of the

following points to ensure maximum safety and reliability of your installation.

1. Before installing check the surrounding environment. Carefully evaluate any hazards which

could be physical damage (transiting vehicles, parts of trees falling etc.), possible contact with

persons’bodies (insects, leaves, etc.), flooding hazards, or any others exceptional events.

2. Check the main voltage numbers is the same as the numbers that are given on the rating

plate and in this manual.

3. Check and make sure if there is suitable electrical protection against short circuits/power

spikes and proper earthed on the main supply.

Remember the unit having main voltage running through it (electrocution hazard, fire

hazard).

4. Take care with the control unit; the parts may be subject to damage if the control unit is

abused.

5. Make sure that you have all the necessary materials, and they are suitable for this kind of

use.

6. Read all the instructions thoroughly, and make sure they are understood before attempting

to install the opener.

7. Before starting the installation carefully analyze all the risks relating to automating the door.

Verify that the door is automated in a sound condition and that the mechanisms are in good

working order. Observe the safety margins and minimum distances.

8. Carefully evaluate the safety devices to be installed and the right place to install them; always

install an emergency stop device for power interruption to the opener if it is required.

9. Once the risks have been analyzed, install the opener and relative safety devices,

emergency stop and/or photoelectric cells.

Important note: As for additional safety rules, we strongly recommends the fitting of Photo

Electric safety beams on all installations.

10.While installing the opener,strictly follow all the instructions given in the instructionmanual.

If some points or procedures in this manual are not very clear do not install the unit until all

doubts have been cleared up with our technical department.

Basic function setting and applying

1. Travel limit setting Opening & closing force self-learning

2. Matching the receiver and transmitter

Fig. A

Fig. B

1. Press ‘SET’button and hold on until the LED

displays figure ‘1’,

2. Then adjust the up limit by pressing ‘LIM-1’

button. Fine-tuning ‘LIM-1’ or ‘LIM-2’ button to

determine the final up limit position then press

‘set’ button the display turn into ‘2’ automatically.

3. Adjust the down limit by pressing ‘LIM-2’ button.

Fine-tuning ‘LIM-1’ or ‘LIM-2’ button to

determine the final down limit position then

press ‘set’ button.

4. The opener will operate a cycle automatically to

remember the limit positions and the opening &

closing force.

1. Press ‘CODE’ button and hold on until the LED dot

is on. (Fig. A)

2. Then press any button on the transmitter once, the

dot will be off; press the button again the dot will

fast flash then LED displays ‘11’(Fig. B). After that

the transmitter will be available.

Press ‘CODE’ button more than 8 seconds until the

LED displays ‘C’, all the stored codes will be deleted.

3. Safety reverse force adjustment

4. Auto-close setting

4．Photo beam setting

5. O/S/C Button

1. Press ‘SET’ button and hold on until the LED

displays ‘3’. It’s under force adjustment mode.

2. Press ‘LIM-1’ button to increase the force and

‘LIM-2’ button to decrease the force.

3. The maximum force is 9 and the minimum is 1.

Press ‘SET’ button to confirm.

1. Press ‘LIM-1’ button and hold on until the LED displays

‘-’.

2. Press ‘LIM-1’ button once, the auto-close time will

increase 1 minute, the maximum time is 9 minutes.

Press ‘LIM-2’ button the auto-close time decrease 1

minute. The auto-close function will be turned off when

LED displays 0.

3. Press ‘SET’ button to confirm.

1. Press ‘LIM-2’ button and hold on until the LED

displays’11’,

2. Press ‘LIM-1’ button the LED displays ‘H’, photo beam

function is available. Press ‘DOWN’ button the LED

displays ‘11’ to cancel this function.

3. When setting is finished, press ‘SET’ to confirm.

When connecting pulsed quantity control infrared

sensor, wiring as Fig. 3. When infrared sensor is

controlled by switch value, wiring as Fig. 1

Notice: Close the photo beam function when you hasn’t

connected any photo beam sensor, otherwise the door can

not been closed.

Make adjustment, maintenance and emergent opening or

closing convenient

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Napoleon Garagentoröffner Handbücher

Napoleon

Napoleon SDO800 Montageanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung