Napoleon HDX52NT-1 Bedienungsanleitung

W415-1371 / 09.15.14

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE

INSTALLATION AND

OPERATING INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁreplaces.com • [email protected]

1.28E

$10.00

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with the appliance and

shall be installed.

SAFETY INFORMATION

!WARNING

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by a

qualiﬁed installer, service agency or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

If the information in these instructions

are not followed exactly, a ﬁre or

explosion may result causing property

damage, personal injury or loss of life.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

Decorative Product: Not for use as a heating appliance.

BARRIER

SAFETY BARRIER

HDX52NT-1

NATURAL GAS

HDX52PT-1

PROPANE

CONFORMS TO AMERICAN NATIONAL STANDARDS: ANSI Z21.50, CERTIFIED TO CANADIAN CSA 2.22 FOR VENTED GAS FIREPLACES.

W415-1371 / 09.15.14

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

TABLE OF CONTENTS

1.0 INSTALLATION OVERVIEW 3

2.0 INTRODUCTION 4

2.1 DIMENSIONS 5

2.2 GENERAL INSTRUCTIONS 5

2.3 GENERAL INFORMATION 6

2.4 RATING PLATE INFORMATION 7

3.0 VENTING 8

3.1 VENTING LENGTHS AND COMPONENTS 8

3.2 TYPICAL VENT INSTALLATION 9

3.3 VENT TERMINAL CLEARANCES 10

3.4 VENT APPLICATION FLOW CHART 11

3.5 DEFINITIONS 11

3.6 ELBOW VENT LENGTH VALUES 11

3.7 HORIZONTAL TERMINATION 12

3.8 VERTICAL TERMINATION 14

4.0 INSTALLATION 16

4.1 WALL AND CEILING PROTECTION 16

4.1.1 HORIZONTAL INSTALLATION 17

4.1.2 VERTICAL INSTALLATION 17

4.2 USING FLEXIBLE VENT COMPONENTS 18

4.2.1 HORIZONTAL AIR TERMINAL INSTALLATION 18

4.2.2 VERTICAL AIR TERMINAL INSTALLATION 19

4.2.3 APPLIANCE VENT CONNECTION 20

4.3 MOBILE HOME INSTALLATION 20

4.4 GAS INSTALLATION 21

5.0 FRAMING 22

5.1 INSTALLING NON-COMBUSTIBLE BOARD 25

5.2 MINIMUM CLEARANCE TO COMBUSTIBLE ENCLOSURES 27

5.3 MINIMUM COMBUSTIBLE MANTEL CLEARANCES 29

5.4 NON-COMBUSTIBLE FACING MATERIAL 30

6.0 FINISHING 31

6.1 SAFETY SCREEN REMOVAL / INSTALLATION 31

6.2 LATCH DOOR ENGAGING / DISENGAGING 32

6.3 GLASS DOOR REMOVAL / INSTALLATION 33

6.4 BURNER INSTALLATION 34

6.5 LOGO PLACEMENT 34

7.0 ELECTRICAL INFORMATION 35

7.1 HARD WIRING CONNECTION 35

7.2 RECEPTACLE WIRING DIAGRAM 35

7.3 BATTERY HOLDER INSTALLATION 36

7.4 WIRING DIAGRAM 37

8.0 OPERATION 38

8.1 GENERAL TRANSMITTER LAYOUT 38

8.2 INITIALIZING THE TRANSMITTER/BATTERY HOLDER FOR THE FIRST TIME 38

8.3 TEMPERATURE DISPLAY 39

8.4 FLAME HEIGHT 39

8.5 NIGHT LIGHT DIMMER CONTROL 39

8.6 CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTION 40

8.7 KEY LOCK 40

8.8 LOW BATTERY / MANUAL BYPASS 40

9.0 OPERATING INSTRUCTIONS 41

9.1 RESTRICTING VERTICAL VENTS 42

9.2 PILOT BURNER ADJUSTMENT 42

9.3 VENTURI ADJUSTMENT 43

9.4 FLAME CHARACTERISTICS 43

10.0 MAINTENANCE 44

10.1 ANNUAL MAINTENANCE 45

10.2 CONTROL ACCESS 46

10.3 BURNER REMOVAL 47

10.4 BRICK PANEL REMOVAL 47

10.5 PORCELAIN PANEL REMOVAL 47

10.6 MEDIA TRAY REMOVAL (GLASS ONLY) 47

10.7 NIGHT LIGHT REPLACEMENT 48

10.8 GLASS / DOOR REPLACEMENT 49

10.9 CARE OF GLASS 49

10.10 CARE OF PLATED PARTS 49

11.0 REPLACEMENTS 50

12.0 OVERVIEW 51

13.0 ACCESSORIES 52

14.0 LOG BURNER 54

15.0 GLASS BURNER 55

16.0 TROUBLESHOOTING 58

17.0 WARRANTY 61

18.0 SERVICE HISTORY 62

19.0 NOTES 63

The camera icon indicates video tutorials are available as additional reference,

visit http://www.napoleonﬁreplaces.com/category/product-support/support-centre/

W415-1371 / 09.15.14

1.0 INSTALLATION OVERVIEW

See the section

“FRAMING -

MINIMUM MANTEL

CLEARANCES”

See the section

“FRAMING - MINIMUM

CLEARANCE TO

COMBUSTIBLE

ENCLOSURES” for

drywall (or other

combustible material)”

See the section

“FRAMING”

Side

Wall

See the section

“VENTING - VENTING

LENGTHS AND AIR TERMINAL

LOCATIONS”

See the section

“FRAMING”

See the section

“FRAMING - MINIMUM

CLEARANCE TO

COMBUSTIBLE

ENSLOSURES” for

non-combustible

materials such as tile,

marble, granite, etc.

IMPORTANT: Extra

support may be

required.

See the section

“CONTROLACCESS”

for the control box.

See the section

“BATTERY HOLDER”

See the section

“BURNER INSTALLATION”

SAFETY BARRIER

Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled,

and may be accepted for disposal at your local recycling center. Check with your municipality for recycling

instructions.

W415-1371 / 09.15.14

3.2C

WARNING

• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.

• ANY CHANGES OR ALTERATIONS TO THIS APPLIANCE OR ITS CONTROLS CAN BE DANGEROUS AND IS

PROHIBITED.

• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance

according to operating instructions could cause ﬁre or injury.

• Risk of ﬁre or asphyxiation do not operate appliance with ﬁxed glass removed.

• Do not connect 110 volts to the control valve.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges may

be sharp.

• Do not burn wood or other materials in this appliance.

• Children and adults should be alerted to the hazards of high surface temperature and should stay away to

avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier

is recommended if there are at risk individuals in the house. To restrict access to an appliance, install an

adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and

away from hot surfaces.

• Clothing or other ﬂammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁc and away from furniture and

draperies.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot

surfaces. These screens and guards must be fastened to the ﬂoor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior to operating

the appliance.

• The appliance is a vented gas-ﬁred appliance. Do not burn wood or other materials in the appliance

• It is imperative that the control compartments, burners and circulating blower and its passageway in the appliance

and venting system are kept clean. The appliance and its venting system should be inspected before use and at

least annually by a qualiﬁed service person. More frequent cleaning may be required due to excessive lint from

carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials,

gasoline and other ﬂammable vapors and liquids.

• Under no circumstances should this appliance be modiﬁed.

• This appliance must not be connected to a chimney ﬂue pipe serving a separate solid fuel burning appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁed service technician to inspect

the appliance and to replace any part of the control system and any gas control which has been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be

done by a licensed or qualiﬁed service person.

• Do not strike or slam shut the appliance glass door.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating to prevent

exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of the exhaust escaping

through these openings can also cause the surrounding combustible materials to overheat and catch ﬁre.

• Only doors / optional fronts certiﬁed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic

bags, these are not toys and should be kept away from children and infants.

• As with any combustion appliance, we recommend having your appliance regularly inspected and serviced as well

as having a Carbon Monoxide Detector installed in the same area to defend you and your family against Carbon

Monoxide.

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance.

Elevated temperatures on the wall or in the air above the appliance can cause melting, discolouration or damage of

decorations, a T.V. or other electronic components.

• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and

shall be installed.

• If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier for this

appliance.

• Installation and repair should be done by a qualiﬁed service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments,

burners and circulating air passageways of the appliance be kept clean.

2.0 INTRODUCTION

W415-1371 / 09.15.14

56 7/8"

1445mm

54 13/16"

1392mm 50 3/8"

1280mm

41 7/8"

1064mm

27 1/8"

689mm

29 1/8"

740mm

47 17/32"

1207mm

44 3/4" 1137mm

51mm

38 7/8"

987mm

Ø 10 7/8"

276mm

Ø 7 7/8"

200mm

9 3/16"

233mm

SAFETY BARRIER

2.1 DIMENSIONS

THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to

conform with local codes. Installation practices vary from region to region and it is important to know the

speciﬁcs that apply to your area, for example in Massachusetts State:

• This product must be installed by a licensed plumber or gas ﬁtter when installed within the commonwealth

of Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance

insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂexible connector must not be longer than 36 inches (914mm).

• A Carbon Monoxide detector is required in all rooms containing gas ﬁred appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent

sealed combustion product.

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT,

WITH THE GLASS DOOR OPENED OR REMOVED.

PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.

PROVIDE ADEQUATE VENTILATION.

NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.

OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” (1219mm) FROM

THE FRONT FACE OF THE APPLIANCE.

SURFACES AROUND AND ESPECIALLY ABOVE THE APPLIANCE CAN BECOME HOT. AVOID CONTACT

WHEN THE APPLIANCE IS OPERATING.

FIRE RISK. EXPLOSION HAZARD.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE PRESSURE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG. CLOSE THE MANUAL SHUT-OFF VALVE BEFORE PRESSURE

TESTING GAS LINE AT TEST PRESSURES EQUAL TO OR LESS THAN 1/2 PSIG (35 mb).

USE ONLY WOLF STEEL APPROVED OPTIONAL ACCESSORIES AND REPLACEMENT PARTS WITH THIS APPLIANCE.

USING NON-LISTED ACCESSORIES (BLOWERS, DOORS, LOUVRES, TRIMS, GAS COMPONENTS, VENTING

COMPONENTS, ETC.) COULD RESULT IN A SAFETY HAZARD AND WILL VOID THE WARRANTY AND CERTIFICATION.

WARNING

2.2 GENERAL INSTRUCTIONS

W415-1371 / 09.15.14

This appliance is approved for bathroom, bedroom and bed-sitting room installations and is certiﬁed for mobile

home installation.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁed kit is used.

When the appliance is installed at elevations above 4,500ft (1371m), and in the absence of speciﬁc

recommendations from the local authority having jurisdiction, the certiﬁed high altitude input rating shall be

reduced at the rate of 4% for each additional 1,000ft (305m).

Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected.

Change in ﬂame appearance from “HI” to “LO” is more evident in natural gas than in propane.

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the

appliance and shall be installed.

2.3 GENERAL INFORMATION

4.1B

The installation must conform with local codes or, in

absence of local codes, the National Gas and Propane

Installation Code CSA B149.1 in Canada, or the National

Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United

States. Suitable for mobile home installation if installed in

accordance with the current standard CAN/CSA Z240MH

Series, for gas equipped mobile homes, in Canada or

NSI Z223.1 and NFPA 54 in the United States.

s long as the required clearance to combustibles is

maintained, the most desirable and beneﬁcial location

for an appliance is in the center of a building, thereby

allowing the most efﬁcient use of the heat created. The location of windows, doors and the trafﬁc ﬂow in the

room where the appliance is to be located should be considered. If possible, you should choose a location

where the vent will pass through the house without cutting a ﬂoor or roof joist.

If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood

ﬂooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.

Some appliances have optional fans or blowers. If an optional fan or blower is installed, the junction box must

be electrically connected and grounded in accordance with local codes, use the current CSA C22.1 Canadian

Electrical Code in Canada or the ANSI/NFPA 70 National Electrical code in the United States.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

(NFI) as NFI Gas

Specialists

www.ncertied.org

FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND

QUALITY!

HDX52-1

NG LP

Altitude (FT) 0-4,500 0-4500

Max. Input (BTU/HR) 55,000 55,000

Max. Output Steady State (BTU/HR) 37,391 36,500

Efﬁciency (w/the fan on) 64% 68%

Min. Inlet Gas Supply Pressure 4.5" w.c. (11mb) 11" w.c. (27mb)

Max. Inlet Gas Supply Pressure 7" w.c. (17mb) 13" w.c. (32mb)

Manifold Pressure (Under Flow Conditions) 3.5" w.c. (9mb) 10" w.c. (25mb)

W415-1371 / 09.15.14

2.4 RATING PLATE INFORMATION

NOTE: The protective wrap on plated parts is best removed when

the assembly is at room temperature but this can be improved if

the assembly is warmed, using a hair dryer or similar heat source.

This appliance is equipped with a remote control system, which

requires batteries (supplied) to be installed. The transmitter takes 1

9V battery and in the case of a power failure the receiver takes 4 “AA”

batteries.

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to

the model, venting and gas type of the appliance.

The illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

65%

HDX52

SAMPLE

Both the rating plate and lighting instructions are attached to a cable and inserted along the left side of the ap-

pliance.

WARNING

ALLOW APPLIANCE TO COOL BEFORE PERFORMING ANY MAINTANCE OR CLEANING.

W385-1928 / C

CHDX52N CHDX52P

CONFORMS TO / CONFORMEAUX: ANSI Z21.50-2014, CERTIFIED TO / CERTIFIE CSA2.22-2014 VENTED GAS FIREPLACE / FOYER À GAZ VENTILÉ.

DIRECT VENT GAS FIREPLACE.

NOT FOR USE WITH SOLID FUEL.

FOR USE WITH GLASS DOORS

CERTIFIED WITH THIS UNIT ONLY.

WARNING: DO NOT ADD ANY MATERIAL

TO THE APPLIANCE, WHICH WILLCOME IN

CONTACT WITH THE FLAMES, OTHER THAN

THAT SUPPLIED BY THE MANUFACTURER

WITH THE APPLIANCE

DECORATIVE PRODUCT: NOT FOR USE AS A

HEATING APPLIANCE.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS:

TOP 0"

FLOOR 0"

RECESSED DEPTH 29"

SIDES 0"

BACK 0"

VENT TOP 3"

VENT SIDES & BOTTOM 2"

VERTICAL VENT 1"

MANTEL 6"*

TOP SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING

MATERIALS. FOR FINISHING MATERIALS SEE OWNER’S MANUAL

*MAXIMUM HORIZONTAL EXTENSION 2". SEE INSTRUCTION MANUAL FOR GREATER

EXTENSIONS. SEE OWNER’S INSTRUCTION MANUAL FOR MINIMUMAND

MAXIMUM LENGTHS.

ELECTRICAL RATING: 115V.60HZ. LESS THAN 12 AMPERES

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE, ON, L4M 0G8 CANADA

SPÉCIFICATIONS ÉLECTRIQUES : 115 V,

60HZ. MOINS DE 12 AMPÈRES.

HDX52N HDX52P

MODEL PROPANE /

PROPANE MODÈLE FOYER À D'ÉVENT DIRECT. UN

COMBUSTIBLE SOLIDE NE PAS

ÊTRÉ UTILISÉ AVEC CET

APPAREIL. UTILISER AVEC LES

PORTE VITRÉES HOMOLOGUÉES

SEULEMENT AVEC CETTE UNITÉ.

ADVERTISSEMENT : N’AJOUTEZ PAS

A CETAPPAREIL AUCUN MATÉRIAU DEVANT

ENTRER EN CONTACT AVEC LES FLAMMES

AUTRE QUE CELUI QUI EST FOURNI AVECT

CET APPAREIL PAR LE FABRICANT.

PRODUIT DÉCORATIF: NE PAS UTILISER

COMME APPAREIL DE CHAUFFAGE

DÉGAGEMENTS MINIMAUX DES MATÉRIAUX

COMBUSTIBLES :

DESSUS 0"

PLANCHER 0"

PROFONDEUR DE L’ENCLAVE FACE 29"

CÔTÉS 0"

ARRIÈRE 0"

DESSUS DU CONDUIT D’EVENT 3"

CÔTÉS ET DESSOUS DU CONDUIT

D’EVENT 2"

CONDUIT D’EVENT VERTICAL 1"

TABLETTE 6"*

DESSUS, CÔTÉS & ARRIÈRE : SELON LES ESPACEURS DE

DÉGAGEMENT POUR LES MATERIAUX D’OSSATURE SELON

LA MANUELDE PROPRIÉTAIRE POUR LES MATÉRIAUX DE

FINITION. *L’EXTENSION HORIZONTALE MAXIMALE : 2".

RÉFÉRER AU MANUALD’INSTRUCTION POUR DES

EXTENSIONS PLUS GRANDES. RÉFÉRER AU MANUEL

D’INSTALLATION DE PROPRIÉTAIRE.

MODEL NATURAL GAS /

GAZ NATURAL

0-4500FT (0-1370M) ALTITUDE / ÉLÉVATION 0-4500FT (0-1370M)

55,000 BTU/H

INPUT / ALIMENTATION 55,000 BTU/H

37,000 BTU/H REDUCED INPUT / ALIMENTATION RÉDUITE 36,500 BTU/H

3.5"WATER COLUMN/D’UNE COLONNE D’EAU MANIFOLD PRESSURE / 10"WATER COLUMN/D’UNE COLONNE D’EAU

PRESSION AU COLLECTEUR

4.5"WATER COLUMN/D’UNE COLONNE D’EAU MINIMUM SUPPLY PRESSURE / 11"WATER COLUMN/D’UNE COLONNE D’EAU

PRESSION D’ALIMENTATION MINIMALE

7.0"WATER COLUMN/D’UNE COLONNE D’EAU MAXIMUM SUPPLY PRESSURE 13"WATER COLUMN/D’UNE COLONNE D’EAU

PRESSION D’ALIMENTATION MAXIMALE

65.2% P.4 FE 65.2%

SERIAL NUMBER/ NO. DE SÉRIE: HDX52

L’APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT

L’ENSEMBLE D’ÉVACUATION PROPRE ANAPOLEON. RÉFÉRER

AU MANUEL D’INSTALLATION DE PROPRIÉTAIRE POUR

L’EVACUATION PRECISE. IL EST IMPORTANT DE BIEN

RÉINSTALLER ET RESCELLER L’EVENT APRÉSAVOIR ASSURÉ

LE MAINTIEN DU SYSTÉME DE PRISE D’AIR.

THE APPLIANCE MUST BE VENTED USING THEAPPROPRIATE

NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL

FOR VENTING SPECIFICS. PROPER REINSTALLATIONAND

RESEALING IS NECESSARYAFTER SERVICING THE VENT-AIR

INTAKE SYSTEM.

THIS APPLIANCE MUSTBE INSTALLED IN ACCORDANCE WITH LOCALCODES, IFANY; IF NONE, FOLLOW THE

CURRENTANSI Z223.1 OR CSAB149, INSTALLATION CODES. VENTED GAS FIREPLACE.APPROVED FOR

BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME

INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD CAN/CSA Z240MH SERIES

GAS EQUIPPED MOBILE HOMES, IN CANADA OR INTHE UNITED STATES THE MANUFACTURED HOME

CONSTRUCTION AND SAFETYSTANDARD, TITLE 24 CFR, PART 3280. WHEN THIS US STANDARD IS NOT

APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLA-

TIONS, SITES AND COMMUNITIES,ANSI/NFPA 501A. FOR USE WITH BARRIER W565-0148. FOLLOW THE

INSTALLATION INSTRUCTIONS LOCATED IN THE INSTALLATION MANUAL

INSTALLER L’APPAREIL SELON LES CODES D’INSTALLATION ANSI Z223.1 OU CSA-B149 EN VIGUER.

FOYER À GAZ VENTILÉ. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE

BAIN ET UN STUDIO.APPROPRIÉ POUR INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION

CONFORME AUX EXIGENCES DE LANORME CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉESAU

GAZ EN VIGEUR AU CANADAOU AUX ÉTATS-UNIS DE LA NORME DE SECURITE ET DE CONSTRUCTION DE

MAISONS MANUFACTUREE,TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D’ÉTATS-UNIS NE

PEUT ETREAPPLIQUÉE, SE REFERER ALA NORME RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ

CONTRE L’INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES SITES ET LES

COMMUNAUTÉS, ANSI/NFPA 501A. POUR UNE UTILISERAVEC BARRIÈRE W565-0148. SUIVEZ LES

INSTRUCTIONS D'INSTALLATION SE TROUVENT DANS LE MANUEL D'INSTALLATION.

9700539 (WSL)

4001658 (NAC) 4001657 (NGZ)

4001659 (WUSA)

OPTIONAL FAN KIT: NZ64 ENSEMBLE DE VENTILATEUR FACULTATIF: NZ64

W415-1371 / 09.15.14

3.0 VENTING

3.1 VENTING LENGTHS AND COMPONENTS

This ﬁreplaces uses 8" (203mm) exhaust / 11" (280mm) air intake vent pipe system.

Refer to the section applicable to your installation.

For safe and proper operation of the ﬁreplace follow the venting instruction exactly. Deviation from the minimum

vertical vent length can create difﬁculty in burner start-up and/or carboning. Under extreme vent conﬁgurations,

allow several minutes (5-15) for the ﬂame to stabilize after ignition. Provide a means for visually checking the vent

connection to the ﬁreplace after the ﬁreplace is installed. Use a ﬁrestop, vent pipe shield or attic insulation shield

when penetrating interior walls, ﬂoor or ceiling.

NOTE: If for any reason the vent air intake system is disassembled; reinstall per the instructions provided

for the initial installation. 7.7

WARNING

RISK OF FIRE, MAINTAIN SPECIFIED AIR SPACE CLEARANCES TO VENT PIPE AND APPLIANCE.

IF VENTING IS INCLUDED WITH SPACERS THE VENT SYSTEM MUST BE SUPPORTED EVERY 3FT

(0.9m) FOR BOTH VERTICAL AND HORIZONTAL RUNS. USE SUPPORTS OR EQUIVALENT

NON-COMBUSTIBLE STRAPPING TO MAINTAIN THE REQUIRED CLEARANCE FROM

COMBUSTIBLES. SPACERS ARE ATTACHED TO THE INNER PIPE AT PREDETERMINED INTERVALS

TO MAINTAIN AN EVEN AIR GAP TO THE OUTER PIPE. THIS GAP IS REQUIRED FOR SAFE

OPERATION. A SPACER IS REQUIRED AT THE START, MIDDLE AND END OF EACH ELBOW TO

ENSURE THIS GAP IS MAINTAINED. THESE SPACERS MUST NOT BE REMOVED.

For vent systems that provide seals on the inner exhaust ﬂue, only the outer air intake joints must be sealed

using a red high temperature silicone (RTV). This same sealant may be used on both the inner exhaust and

outer intake vent pipe joints of all other approved vent systems except for the exhaust vent pipe connection to the

ﬁreplace ﬂue collar which must be sealed using the black high temperature sealant Mill Pac.

When using Wolf Steel venting components, use only approved Wolf Steel ﬂexible components with the

following termination kits: wall terminal kit GD622R, or 1/12 to 7/12 pitch roof terminal kit GD610, 8/12 to 12/12

roof terminal kit GD611 or ﬂat roof terminal kit GD612. With ﬂexible venting, in conjunction with the various

terminations, use either the 5 foot (1.5m) vent kit GD620 or the 10 foot (3m) vent kit GD630.

For optimum ﬂame appearance and ﬁreplace performance, keep the vent length and number of elbows to

a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to

verify that it is unobstructed and undamaged.

The minimum allowable vertical vent length is 3 feet (0.9m) maximum allowable vertical vent length is 40 feet

(12m). The maximum number of allowable 8” (203mm) vent connections is three horizontally or vertically

(excluding the ﬁreplace and the air terminal connections).

When venting, the horizontal run must be kept to a minimum of 36” (914mm) or a maximum of 20 feet (6m).

If a 20 foot (6m) horizontal run is required, the ﬁreplace must have a minimum vertical rise immediately off

the ﬁreplace of 57” (1448mm). When terminating vertically, the vertical rise is a minimum 36” (914mm) and a

maximum 40 feet (12m) above the ﬁreplace.

For optimum performance, it is recommended that all horizontal runs have a minimum 1/4” (6mm) rise

per foot/meter. Provide a means for visually checking the vent connection to the ﬁreplace after the

ﬁreplace is installed. Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows.

Keep it pulled tight. A 3/4” (19mm) air gap between the inner and outer liner all around is required for saf

operation. Use a ﬁrestop when penetrating interior walls, ﬂoor or ceiling.

8.4A

vertical rise is

GD822R GD810

GD811 GD812

GD820 GD830

18" (457mm)

W415-1371 / 09.15.14

45.8

18" (457mm)

MAXIMUM

24″(610mm)

MIN.

71 1/2"

(1816mm)

PLUS RISE *

16″(406mm)

MINIMUM

40 FEET

(12m)

MAXIMUM

3 FEET (0.9m)

MINIMUM

47 1/2"

(1207mm)

3.2 TYPICAL VENT INSTALLATION

Refer to “VENTING” section.

47 1/2"

(1207mm)

W415-1371 / 09.15.14

3.3 VENT TERMINAL CLEARANCES

INSTALLATIONS

CANADA U.S.A.

A12” (305mm) 12” (305mm) Clearance above grade, veranda porch, deck or balcony.

B12” (305mm)Δ9”

(229mm)ΔClearance to windows or doors that open.

C12” (305mm)* 12” (305mm) * Clearance to permanently closed windows.

D18”

(457mm)** 18” (457mm)** Vertical clearance to ventilated sofﬁts located above the terminal within a horizontal distance of 2’

(0.6m) from the center line of the terminal.

E12” (305mm)** 12” (305mm)** Clearance to unventilated sofﬁt.

F0” (0mm) 0” (0mm) Clearance to an outside corner wall.

0” (0mm)*** 0”

(0mm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney,

etc.).

2” (51mm)*** 2”

(51mm)***

Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase,

etc.).

H3’(0.9m) 3’ (0.9m)**** Clearance to each side of the center line extended above the meter / regulator assembly to a

maximum vertical distance of 15’ (4.6m).

I3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J12” (305mm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other

appliance.

K6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M12”

(305mm)††

12”

(305mm)**** Clearance under a veranda, porch or deck.

N16” (406mm) 16” (406mm) Clearance above the roof.

O2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P8’ (2.4m) 8’(2.4m) Roof must be non-combustible without openings.

Q3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R6’ (1.8m) 6’ (1.8m) See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an

opening between the terminal and the open side of the structure.

S12” (305mm) 12” (305mm) Clearance under a covered balcony

ΔThe terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂoor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

12.1D

NOTE: Clearances are in accordance with local installation codes and the requirements of the gas supplier.

COVERED BALCONY APPLICATIONS ††*

QMIN RMAX MAX

= 3 feet

(0.9m) = 2 x IHHW

(4.6m)

QACTUAL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Napoleon Gaskamin Handbücher

Napoleon

Napoleon Acies L38N Bedienungsanleitung

Beliebte Gaskamin Handbücher anderer Marken

Heatilator

Heatilator ION-V7 Bedienungsanleitung

Enviro

Enviro westport-steel Bedienungsanleitung

White Mountain Hearth

White Mountain Hearth VFP24FP2(0,1,2,3)L(N,P)-1 Kurzanleitung

Kinder

Kinder Ceasar Bedienungsanleitung

Heat & Glo

Heat & Glo EVEREST-B Bedienungsanleitung

Valor

Valor Ultimate Turbochim BR517R Bedienungsanleitung

HVFL

HVFL 18HVFL Bedienungsanleitung

Enviro

Enviro Berkeley-Nova Bedienungsanleitung

Ekofires

Ekofires eko 5010 Bedienungsanleitung

Flavel

Flavel Regent Bedienungsanleitung

Majestic

Majestic 300DVBLN/PV7 Bedienungsanleitung

Vermont Castings

Vermont Castings 33CFDV(N/P)(V/I)SB Bedienungsanleitung

kozy heat

kozy heat SPRINGFIELD 36 Bedienungsanleitung

Valor

Valor COSYFLAME BR623 Bedienungsanleitung

Wonderfire

Wonderfire sonnet plus br645 VA Bedienungsanleitung

Valor

Valor genesis BR645VA Bedienungsanleitung

Bellfires

Bellfires Corner Bell Large 3 CF Bedienungsanleitung

Kinder

Kinder Oasis Bedienungsanleitung