Napoleon B52NTL Bedienungsanleitung

W415-1632 / C / 10.21.16

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.22D

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁreplaces.com • hearth@napoleonproducts.com

SAFETY INFORMATION

!WARNING

If the information in these instructions are

not followed exactly, a ﬁre or explosion

may result causing property damage,

personal injury or loss of life.

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by a

qualiﬁed installer, service agency, or the supplier.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

$10.00

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

AVERTISSEMENT

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

Une barriére conçu à réduire le risque de brûlures

causées par le verre chaud est fourni avec l’appareil

et sera installé pour la protection des enfants et

d’autres personnes à risque.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁed kit is used.

Decorative Product: Not for use as a heating appliance.

CERTIFIED TO CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22 AND ANSI Z21.50 FOR VENTED GAS FIREPLACES.

HDX52

LOG BURNER

ASSEMBLY

B52NTL

NATURAL GAS

B52PTL

PROPANE

A. Remove the door,

refer to installation

instructions. Remove

the 8 securing screws

and lift the plate

up and out of the

appliance. Gasket will

need to be replaced if

damaged.

A. Attach the burner assembly to the ﬁrebox

base with the 2 screws supplied.

This burner and log assembly are approved for use in the HDX52 gas ﬁreplace only. They are not approved for

use as a stand alone appliance or in conjunction with any other appliance.

1.0 GENERAL INFORMATION

2.0 INSTALLATION

2.1 ACCESS PANEL

2.2 BURNER ASSEMBLY

1.0 GENERAL INFORMATION 2

2.0 INSTALLATION 2

2.1 ACCESS PANEL 2

2.2 BURNER ASSEMBLY 2

2.3 BULKHEADS 3

2.4 HEARTH PANEL INSTALLATION 4

2.5 HEARTH LOG & LOG PLACEMENT 5

2.6 CHARCOAL LUMPS 7

2.7 CHARCOAL EMBERS 7

2.8 VERMICULITE 7

2.9 GLOWING EMBERS 7

3.0 ADJUSTMENT 8

3.1 FLAME CHARACTERISTICS 8

4.0 REPLACEMENTS 9

4.1 LOG BURNER ASSEMBLY (NG) 10

4.2 LOG BURNER ASSEMBLY (P) 11

5.0 NOTES 12

INSIDE UNIT

OUTSIDE UNIT

W415-1632 / C / 10.21.16

NOTE: Changes, other than editorial, are denoted by a line in the margin.

TABLE OF CONTENTS

NOTE: Bulkhead covers need to be removed.

A. Connect the main burner gas ﬂex line

and the pilot line to the gas ﬁttings on the

bulkheads located under the valve access

opening.Care must be taken to ensure the

pilot line isn’t damaged and ensuring gas

tight connections are made.

Main

Burner Gas

Connection

Pilot Tube

Gas Connection

Pilot

Electrode

Lead

Bulkhead

2.3 BULKHEADS

B. Connect the pilot electrode lead to the

bulkhead matching the 3/16" ﬂag with the

3/16" bulkhead spade. Do the same with the

1/4” spark lead to the 1/4” bulkhead spade.

C. Ensure the venturi tubes are over the oriﬁce

before lighting.

D. Check for gas leaks by brushing on a soap

and water solution. Do not use open ﬂame.

E. After leak test has been performed re-install

access panel with gasket.

W415-1632 / C / 10.21.16

Hearth ﬂoor panels are shipped separate from the appliance and are included with the mandatory brick panel

kits. Due to the brittle material of the panels, care must be taken not to bend or force them into place.

When shipped, the hearth panels range in varying shades of Sandstone / New Port. During initial use, the panels

will darken temporarily. The appearance of the panels will permanently lighten in color with use.

INSTALL HEARTH FLOOR PANELS ACCORDING TO THE INSTALLATION LEAFLET.

2.4 HEARTH PANEL INSTALLATION

NOTE: It is recommended to remove the grate assembly prior to panel installation.

W415-1632 / C / 10.21.16

2.5 HEARTH LOG & LOG PLACEMENT

A. Align the 2 holes in the bottom of the

bottom rear log with the studs located

on the rear log support.

B. Align the 2 pins in the bottom of the top

rear log with the holes in the top of the

bottom rear log.

C. Align the 2 holes in the bottom in the

middle log with the studs located on

the front log support.

D. Align the hole in the rear left log with the

left pin of the top rear log.

E. Line the notches in the bottom of the

front right log with the 4th and 5th grate

posts. Make sure not to cover ports.

F. Line the notch in the front left log with

the front left corner of the burner.

W415-1632 / C / 10.21.16

G. Align the 2 holes located in the bottom

of the front left crossover log with the

2 studs on the left hand side of the

burner.

H. Align the 2 holes in the bottom of the

right middle log with the 2 studs on the

right hand side of the burner.

I. Place the top right log on the notches

in the bottom rear log and the front

right log pushing back against the rear

panel.

J. Align the hole and the pin in the right

crossover log with the pin in the top rear

log and the hole in the top right log.

K. Place the notch in the front charcoal

log over the second grate post. Make

sure not to cover any ports.

L. Align the pin in the bottom of the

middle crossover with the hole in the

middle of the middle log resting it on

the front left crossover log.

W415-1632 / C / 10.21.16

2.6 CHARCOAL LUMPS

34.1

Place the lumps in front of the logs in a realistic manner taking care not to block any of the burner ports.

WARNING

CHARCOAL EMBERS, VERMICULITE AND CHARCOAL LUMPS ARE NOT TO BE PLACED ON THE

BURNER.

2.7 CHARCOAL EMBERS

32.1

Randomly place the charcoal embers along the front and sides of the log support tray in a realistic manner.

Fine dust found in the bottom of the bag should not be used.

NOTE:

Charcoal embers are not to be placed on the burner.

2.8 VERMICULITE

33.1

Sprinkle vermiculite around the charcoal embers.

NOTE: Vermiculite is not to be placed on the burner

2.9 GLOWING EMBERS

Tear the embers into pieces and place along the front row of ports covering all of the burner area. Care should

be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the ﬁbre hairs will

glow. The ember material will only glow when exposed to direct ﬂame; however, care should be taken to not

block the burner ports.

Blocked burner ports can cause an incorrect ﬂame pattern, carbon deposits and delayed ignition. Phazer™

logs glow when exposed to direct ﬂame. Use only certiﬁed “glowing embers” and Phazer™ logs available

from your authorized dealer.

W415-1632 / C / 10.21.16

Air Shutter Openings both Burners

LP F 7/16" R 1/4”

NG F 1/16" R 1/16”

3.0 ADJUSTMENT

3.1 FLAME CHARACTERISTICS

This appliance has an air shutter that has been factory set open according

to the chart below:

Regardless of venturi orientation, closing the air shutter will cause a more

yellow ﬂame, but can lead to carbonization. Opening the air shutter will

cause a more blue ﬂame, but can cause ﬂame lifting from the burner ports.

The ﬂame may not appear yellow immediately; allow 15 to 30 minutes for

the ﬁnal ﬂame colour to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED

INSTALLER!

AIR

SHUTTER

OPENING

VENTURI

BURNER

ORIFICE

49.1

It’s important to periodically perform a visual check of the pilot and burner ﬂ ames. Compare them to the

illustration provided. If any ﬂ ames appear abnormal call a service person.

3/8” - 1/2”

(9,5mm - 12,7mm)

FLAME MUST ENVELOP

UPPER 3/8” (9.5mm) TO 1/2”

(12.7mm) OF FLAME SENSOR

PILOT

BURNER

ELECTRODE

FLAME

SENSOR

LA FLAMME DOIT

ENVELOPPER LA PARTIE

SUPÉRIEURE DE LA SONDE

DE FLAMME DE 3/8” (9,5mm)

À 1/2” (12,7mm)

ÉLECTRODE

LA SONDE

DE FLAMME

VEILLEUSE

3/8” - 1/2”

(9.5mm - 12.7mm)

54.1B

W415-1632 / C / 10.21.16

4.0 REPLACEMENTS

41.1C

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts

can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE

REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

•

Model & Serial Number of appliance

•

Installation date of appliance

•

Part number

•

Description of part

•

Finish

PARTS, PART NUMBERS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PARTS IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN 2 TO 5 BUSINESS DAYS FOR MOST

DELIVERY DESTINATIONS.

PARTS NOT IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN A 2 TO 4 WEEK PERIOD, FOR

MOST CASES.

PARTS IDENTIFIED AS ‘SO’ ARE SPECIAL ORDER AND CAN TAKE UP TO 90 DAYS FOR DELIVERY.

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE

ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

** THIS IS A FAST ACTING THERMOCOUPLE. IT IS AN INTEGRAL SAFETY COMPONENT. REPLACE ONLY WITH

A FAST ACTING THERMOCOUPLE SUPPLIED BY WOLF STEEL LTD.

WARNING

W135-0630

W135-0631

W135-0634

W135-0635

W135-0632

W135-0633

W135-0636

W135-0638

W135-0639

W135-0637

W135-0640

W135-0629

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

REF. NO.

PART NUMBER

DESCRIPTION

LOG, REAR TOP

LOG, MIDDLE

LOG, FRONT RIGHT

LOG, FRONT LEFT

LOG, FRONT LEFT CROSSOVER

LOG, REAR LEFT

LOG, RIGHT MIDDLE

LOG, TOP RIGHT

LOG, RIGHT CROSSOVER

LOG, FRONT CHARCOAL

LOG, MIDDLE CROSSOVER

LOG, REAR BOTTOM

4.1 LOG BURNER ASSEMBLY (NG)

W415-1632 / C / 10.21.16

W010-3822-SER

ASSY, GRATE

YES

W100-0205-SER

BURNER, COMPLETE

W010-3818

ASSY, PILOT HIGH TEMP 3-WAY

W080-1645

BRACKET, PILOT SHIELD

W010-3849-SER

ASSY, TUBE BURNER WELDMENT

N255-0002

-SER

FITTING, UNION BULKHEAD

3/8 MF TO 3/8MF

W432-0540-SER

MANIFOLD

W456-0031

FRONT BURNER ORIFICE

W456-0026

REAR BURNER ORIFICE

REF. NO. PART NUMBER DESCRIPTION STOCKED

Andere Handbücher für B52NTL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Napoleon Kamin im Innenbereich Handbücher

Napoleon

Napoleon Ascent 42 B42NTR Bedienungsanleitung

Napoleon

Napoleon Continental Fireplaces CHDX40NT-1 Bedienungsanleitung

Napoleon

Napoleon Oakville GDI3N-1 Bedienungsanleitung

Napoleon

Napoleon BGD42N Bedienungsanleitung

Napoleon

Napoleon PLAZMAFIRE WHVF31 Bedienungsanleitung

Napoleon

Napoleon GDS25N Bedienungsanleitung

Napoleon

Napoleon High Country 7000 Bedienungsanleitung

Napoleon

Napoleon Lambert NEFP27-0519RW Bedienungsanleitung

Napoleon

Napoleon Plazmafire 31 Bedienungsanleitung

Napoleon

Napoleon LHD45P Bedienungsanleitung

Napoleon

Napoleon TORCH GT8N Bedienungsanleitung

Napoleon

Napoleon Vittoria GD19N Bedienungsanleitung

Napoleon

Napoleon HDX52NT Bedienungsanleitung

Napoleon

Napoleon NEFB24H Bedienungsanleitung

Napoleon

Napoleon NEFM33-0414 Bedienungsanleitung

Napoleon

Napoleon Element NEFB36H-BS Bedienungsanleitung

Napoleon

Napoleon ASCENT Bedienungsanleitung

Napoleon

Napoleon NEFE33-0614AM-1 Bedienungsanleitung

Napoleon

Napoleon WHD31N Bedienungsanleitung

Napoleon

Napoleon BGD36CFNTR Bedienungsanleitung

Napoleon

Napoleon EPA 1450 Bedienungsanleitung

Napoleon

Napoleon GVFL24N Bedienungsanleitung

Napoleon

Napoleon BGD36CFNTR Bedienungsanleitung

Napoleon

Napoleon GL22N Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch