Napoleon B81NS Bedienungsanleitung

W415-0808 / D / 11.04.16

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.33A

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)720-9081 • www.napoleonﬁreplaces.com • [email protected]

SAFETY INFORMATION

!WARNING

If the information in these instructions are

not followed exactly, a ﬁre or explosion

may result causing property damage,

personal injury or loss of life.

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier from

a neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier,

call the ﬁre department.

- Installation and service must be performed by a

qualiﬁed installer, service agency or the supplier.

$10.00

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

CERTIFIED

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.50 FOR VENTED GAS FIREPLACES.

HD81-1

RIVER ROCK / STONE

BURNER ASSEMBLY

B81NS

NATURAL GAS

B81PS

PROPANE

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

WARNING

W415-0808 / D / 11.04.16

A. Attach the burner assembly to the ﬁrebox base

with the screws supplied, making sure the pilot

assembly is closest to the valve access opening.

1.0 GENERAL INFORMATION

2.0 INSTALLATION

NOTE: Changes, other than editorial, are denoted by a line in the margin.

TABLE OF CONTENTS

BURNER

ASSEMBLY

PILOT

ASSEMBLY

This rock burner assembly is approved for use in the HD81-1 gas appliance only. It is not approved for use as

a stand alone appliance or in conjunction with any other appliance.

1.0 GENERAL INFORMATION 2

2.0 INSTALLATION 2

2.1 ACCESS PANEL 2

2.2 BURNER ASSEMBLY 2

2.3 BULKHEADS 3

2.4 NIGHT LIGHT™ INSTALLATION 3

2.5 PORCELAIN BASE INSTALLATION 4

2.6 BURNER COVER INSTALLATION 4

2.7 ROCK INSTALLATION 5

3.0 ADJUSTMENT 6

3.1 FLAME CHARACTERISTICS 6

3.2 VENTURI ADJUSTMENT 6

4.0 REPLACEMENTS 6

5.0 B81S OVERVIEW 7

NOTE: The camera icon indicates video tutorials are available as additional reference, visit

http://mynapoleon.napoleonproducts.com/download/index/44/1

2.1 ACCESS PANEL

2.2 BURNER ASSEMBLY

A. Once either door is removed (refer to the “DOOR REMOVAL/INSTALLATION” section of the HD81-1

manual), remove the air manifold by removing the two retaining brackets located at the top of the

ﬁrebox, see Figure 1.

B. Remove the valve access panel and gasket by removing the 8 screws, see Firgure 2.

Fig. 1 Fig. 2

W415-0808 / D / 11.04.16

2.3 BULKHEADS

NOTE: Bulkhead covers need to be removed.

A. Connect the gas ﬂex lines and the pilot line

to the gas bulkheads located under the valve

access opening. Be sure to match up the gas

manifold marked with a dot with the center

bulkhead, also marked with a dot. Care must be

taken to ensure the pilot line isn’t damaged and

ensuring gas tight connections are made.

NOTE: The middle tube is the primary burner

and cannot be turned off. The outside burner

can be turned on and off with the remote. If

this isn’t the case then switch the ﬂex lines.

B. Connect the pilot electrode leads to the

bulkhead. The leads can only ﬁt one way. You

need to match the 1/4” ﬂag with the 1/4” bulkhead

spade and the 3/16” ﬂag with the 3/16” spade.

C. Ensure the 2 venturi tubes are over the oriﬁces

before lighting. NOTE: It is recommended at

this stage to do an operational check before

ﬁnishing installation.

D. Check for gas leaks by brushing on a soap and

water solution. Do not use open ﬂame.

E. After leak test has been performed re-install

access panel with gasket. (If removed) VENTURI

TUBE

ORIFICE

GAS

BULKHEADS

PILOT

BULKHEADS

DOTS

PRIMARY

BURNER

PILOT

ELECTRODE

PILOT

ELECTRODE

LEADS

2.4 NIGHT LIGHT™ INSTALLATION

The HD81-1 comes equipped with two “Night Lights™”. The lights have been pre-wired and are controlled

from the remote control.

If in the event the lamps or lens need replacing, follow the instructions below:

A. Shut off breaker at main power supply

B. Remove the four screws that secure the lens frame to the ﬁrebox sides. This frame retains the glass lens.

C. The lamp can now be accessed.

NOTE: Do not handle the lamp (bulb) with bare ﬁngers, protect with a clean dry cloth.

The lamp will pull straight out of the socket. Replace with Wolf Steel parts only, as lamp and lens are special

“high temperature” products. When re-installing, ensure integrity of gasket seal.

THE FIREBOX MUST BE SEALED.

Over tightening the screws could break the lens. “Light Leakage” from the holes in the housing lamp may be

observed. The holes in the lamp housing are necessary for ventilation and must not be covered.

GASKET

LENS

FRAME

COLOURED SIDE UP

NIGHT LIGHTS

W415-0808 / D / 11.04.16

INSTALL IN THE FOLLOWING ORDER:

A. Side porcelain panels or brick panels must

be installed prior to porcelain base cover

plates. For side porcelain panel installation

see “PRP81 PORCELAIN REFLECTIVE

RADIANT PANEL” leaﬂet and for brick panel

installation see “GD844KT DECORATIVE

BRICK PANEL - SANDSTONE” leaﬂet.

B. Slide the porcelain cover plates through

the front opening being careful not to

scratch the porcelain panels. The cover

plates must slide under the burner cover

as shown. Secure to the burner base with

the screws provided and repeat on other

side. Porcelain wire shields sit on the cover

plates as illustrated.

A. Lower the burner cover down onto the

burner tray and porcelain base, making

sure the pilot is properly seated through

the slot on the right side.

B. Attach burner cover with four screws as

illustrated.

C. Empty the sand into the burner tray.

Spread the sand evenly over the burner

tray.

2.5 PORCELAIN BASE INSTALLATION

PORCELAIN

COVER PLATE

PORCELAIN

WIRE SHIELD

2.6 BURNER COVER INSTALLATION

W415-0808 / D / 11.04.16

2.7 ROCK INSTALLATION

WARNING

REAL ROCKS MUST NOT BE USED IN THIS APPLIANCE. HEAT WILL CAUSE THEM TO EXPLODE.

A. Position the rocks in front of the center burner

tube, ensure not to cover burner ports.

B. Position a few large rocks randomly along the

front, making sure not to cover burner ports.

C. Place a few rocks randomly between the other

rocks, ensure not to cover burner ports.

D. Position the remaining rocks randomly,

ensure not to cover burner ports.

E. Repeat on other side.

W415-0808 / D / 11.04.16

It is important to periodically perform a visual check of the pilot

and burner ﬂames. Compare them to the illustration provided. If

any ﬂames appear abnormal, call a service person.

FLAME MUST ENVELOP

UPPER 3/8” (9.5mm) TO 1/2”

(12.7mm) OF FLAME SENSOR

PILOT

BURNER

ELECTRODE

FLAME

SENSOR

3/8” - 1/2”

(9.5mm - 12.7mm)

54.1B

3.0 ADJUSTMENT

3.1 FLAME CHARACTERISTICS

3.2 VENTURI ADJUSTMENT

This appliance has an air shutter that has been factory set open according

to the chart below:

Regardless of venturi orientation, closing the air shutter will cause a more

yellow ﬂame, but can lead to carbonization. Opening the air shutter will

cause a more blue ﬂame, but can cause ﬂame lifting from the burner ports.

The ﬂame may not appear yellow immediately; allow 15 to 30 minutes for

the ﬁnal ﬂame colour to be established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED

INSTALLER!

AIR

SHUTTER

OPENING

VENTURI

BURNER

ORIFICE

49.1

VENTURI ADJUSTMENT CHART

NG 3/16” (4.8mm)

P 7/16” (11mm)

41.1C

Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts

can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE

REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

PARTS, PART NUMBERS AND AVAILABILITY ARE SUBJECT TO CHANGE WITHOUT NOTICE.

PARTS IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN 2 TO 5 BUSINESS DAYS FOR MOST

DELIVERY DESTINATIONS.

PARTS NOT IDENTIFIED AS STOCKED WILL BE DELIVERED WITHIN A 2 TO 4 WEEK PERIOD, FOR

MOST CASES.

PARTS IDENTIFIED AS ‘SO’ ARE SPECIAL ORDER AND CAN TAKE UP TO 90 DAYS FOR DELIVERY.

FAILURE TO POSITION THE PARTS IN ACCORDANCE WITH THIS MANUAL OR FAILURE TO USE

ONLY PARTS SPECIFICALLY APPROVED WITH THIS APPLIANCE MAY RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

WARNING

4.0 REPLACEMENTS

W415-0808 / D / 11.04.16

REF. NO. PART NUMBER DESCRIPTION

ITEMS MAY NOTAPPEAR EXACTLY AS ILLUSTRATED

W010-2863 PILOTASSEMBLY (NG)

W335-0039 PILOT HOOD

BURNER ASSEMBLY

STOCKED STOCKED

W455-0068 PILOT ORIFICE #35 (P)

W455-0070 PILOT ORIFICE #62 (NG)

W010-2900 PILOTASSEMBLY (P)

W750-0335 ELECTRODE

W750-0336 FLAME SENSOR

W100-0113

W456-0034 INSIDE BURNER ORIFICE #34 (NG)

W456-0054 INSIDE BURNER ORIFICE #54 (P)

W456-0034 OUTSIDE BURNER ORIFICE #34 (NG)

W456-0052 OUTSIDE BURNER ORIFICE #52 (P)

W200-0274-BK2GL-SER ROCK BURNER COVER

REK ROCK KIT

YES

W550-0009 WHITE SAND (8LBS)

3/8” FLEX CONNECTOR (24”)

W175-0289 3/8” FLEX CONNECTOR

W175-0227

W565-0109 BURNER SCREEN

W350-0460-BK2GL-SER ROCK BURNER HOUSING

YES

5.0 B81S OVERVIEW

Other Napoleon

Products

'JSFQMBDF*OTFSUTt$IBSDPBM(SJMMT t(BT'JSFQMBDFTt8BUFSGBMMTt8PPE4UPWFT

)FBUJOH$PPMJOHt&MFDUSJD'JSFQMBDFTt0VUEPPS'JSFQMBDFTt(BT(SJMMT

'JSFQMBDFT)FBUJOH$PPMJOHDBMMt(SJMMTDBMM

napoleonproducts.com

/BQPMFPO3PBE#BSSJF0OUBSJP$BOBEB-.(

#BZWJFX%SJWF#BSSJF0OUBSJP$BOBEB-/:

.JMMFS%SJWF$SJUUFOEFO,FOUVDLZ64"

5SBOT$BOBEB)JHIXBZ.POUSFBM2VFCFD$BOBEB)5"

W415-0808 / D / 11.04.16

INSTALLATEUR : LAISSEZ CE MANUEL AVEC L’APPAREIL.

PROPRIÉTAIRE : CONSERVEZ CE MANUEL POUR CONSULTATION ULTÉRIEURE.

NE LAISSEZ PAS LES ENFANTS OU AUTRES INDIVIDUS À RISQUE SEULS À PROXIMITÉ DE L’APPAREIL.

1.33A

CONSIGNES DE SÉCURITÉ

$10.00

Cet appareil peut être installé dans une maison

préfabriquée (mobile) déjà instalée à demeure si les

règlements locaux le permettent.

Cet appareil doit être utilisé uniquement avec le type de

gaz indiqué sur la plaque signalétique. Cet appareil ne

peut être converti à d’autres gaz, sauf si une trousse de

conversion est utilisée.

CERTIFIED

INSTRUCTIONS

D’INSTALLATION ET

D’OPÉRATION

AVERTISSEMENT

Si ces instructions ne sont pas suivies à la

lettre, un incendie ou une explosion pourraient

s’ensuivre, causant des dommages matériels,

des blessures corporelles ou des pertes de vie.

- N’entreposez pas et n’utilisez pas d’essence ou autres

liquides et vapeurs inﬂammables à proximité de cet

appareil ou tout autre appareil.

- QUE FAIRE SI VOUS DÉTECTEZ UNE ODEUR DE GAZ :

• N’allumez aucun appareil.

• Ne touchez à aucun interrupteur électrique;

n’utilisez aucun téléphone dans votre immeuble.

• Appelez immédiatement votre fournisseur de gaz

d’un téléphone voisin. Suivez ses instructions.

• Si vous ne pouvez pas rejoindre votre fournisseur

de gaz, appelez le service des incendies.

- L’installation et l’entretien doivent être faits par un

installateur qualiﬁé, une agence d’entretien ou le

fournisseur.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Téléphone 705-721-1212 • Télécopieur 705-720-9081 • www.napoleonfoyers.com • [email protected]

HOMOLOGUÉ SELON LES NORMES NATIONALES CANADIENNES ETAMÉRICAINES CSA 2.33 ET ANSI Z21.50 POUR LES APPAREILS À GAZ VENTILÉS.

B81NS

GAZ NATUREL

B81PS

PROPANE

HD81-1

ASSEMBLAGE DU

BRÛLEUR POUR ROCHES

DE RIVIÈRE

LA VITRE CHAUDE CAUSERA

DES BRÛLURES.

NE PAS TOUCHER LA VITRE

AVANT QU’ELLE AIT REFROIDI.

NE JAMAIS LAISSER LES

ENFANTS TOUCHER LA VITRE.

AVERTISSEMENT

W415-0808 / D / 11.04.16

1.0 INFORMATION GÉNÉRALE 12

2.0 INSTALLATION 12

2.2 PANNEAU D’ACCÈS 12

2.1 ASSEMBLAGE DU BRÛLEUR 12

2.3 RACCORDS 13

2.4 INSTALLATION DE LA LUMIÈRE DE VEILLE 13

2.5 INSTALLATION DE LA PLAQUE DE RECOUVRMENT EN PORCELAINE 14

2.6 INSTALLATION DU COUVERCLE DU BRÛLEUR 14

2.7 INSTALLATION DES ROCHES 15

3.0 RÉGLAGES 16

3.1 CARACTÉRISTIQUES DE LA FLAMME 16

3.2 RÉGLAGE DU VENTURI 16

4.0 RECHANGES 16

5.0 VUE D’ENSEMBLE DU B81S 17

1.0 INFORMATION GÉNÉRALE

2.0 INSTALLATION

2.1 ASSEMBLAGE DU BRÛLEUR

NOTE : Les modiﬁcations, autres qu’éditoriales, sont indiquées par une ligne verticale dans la marge.

TABLE DES MATIÈRES

Cet assemblage de brûleur pour braises vitriﬁées est approuvé pour utilisation dans l’appareil au gaz HD81

seulement. Il n’est pas approuvé pour utilisation comme appareil autonome ou avec n’importe quel autre appareil.

2.2 PANNEAU D’ACCÈS

NOTE: L'icône du camera indique que les vidéos sont disponibles comme une référence

supplémentaire, visitez http://mynapoleon.napoleonproducts.com/download/index/44/1

A. Fixez le brûleur à la base de la chambre

de combustion à l’aide des vis fournies,

en vous assurant que l’assemblage de

veilleuse est placé du côté de l’ouverture

d’accès de la soupape.

Brûleur Assemblage

de veilleuse

A. Une fois que vous avez enlevé une des portes (voir la section “INSTALLATION / ENLÈVEMENT DE LA

PORTE” dans votre manuel d’instructions d’installation du HD81-1), retirer le collecteur d’air en enlever

les deux supports de ﬁxation dans la partie supérieure de la chambre de combustion, voir Figure 1.

B. Retirez le panneau d’accès de la soupape et le joint d’étancheité en enlever les 8 vis, voir Firgure 2.

Fig. 1 Fig. 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Napoleon Kamin im Innenbereich Handbücher

Napoleon

Napoleon BGD42CFN Bedienungsanleitung

Napoleon

Napoleon EF38H Bedienungsanleitung

Napoleon

Napoleon GD33NR Bedienungsanleitung

Napoleon

Napoleon Park Avenue GD82NT-PA Bedienungsanleitung

Napoleon

Napoleon fireplaces Bedienungsanleitung

Napoleon

Napoleon GD36NTR Bedienungsanleitung

Napoleon

Napoleon NEFE33-0614 Bedienungsanleitung

Napoleon

Napoleon GI3014-N Bedienungsanleitung

Napoleon

Napoleon BGD40-N Bedienungsanleitung

Napoleon

Napoleon Roxbury GI3600-4NSB Bedienungsanleitung

Napoleon

Napoleon Element NEFB42H-BS Bedienungsanleitung

Napoleon

Napoleon High Country 5000 Bedienungsanleitung

Napoleon

Napoleon NEFE30-3620RLB Bedienungsanleitung

Napoleon

Napoleon NEFP42-1715BW Bedienungsanleitung

Napoleon

Napoleon GX70NTE Bedienungsanleitung

Napoleon

Napoleon GDS 50-N Betriebsanleitung

Napoleon

Napoleon Ascent 42 B42NTR Bedienungsanleitung

Napoleon

Napoleon CLEARion Elite NEFBD60HE Bedienungsanleitung

Napoleon

Napoleon WHD48N Bedienungsanleitung

Napoleon

Napoleon B36NT Bedienungsanleitung

Napoleon

Napoleon GVFS60-P Bedienungsanleitung

Napoleon

Napoleon TriVista Series Bedienungsanleitung

Napoleon

Napoleon NEFP32-5320BW-EU Bedienungsanleitung

Napoleon

Napoleon BGD48N Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Regency Fireplace Products

Regency Fireplace Products Pro Series Kurzanleitung