Napoleon HDX35 Bedienungsanleitung

W415-1451 / A / 07.21.15

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.22D

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleonﬁreplaces.com • [email protected]

SAFETY INFORMATION

!WARNING

If the information in these instructions are

not followed exactly, a ﬁre or explosion

may result causing property damage,

personal injury or loss of life.

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by a

qualiﬁed installer, service agency or the supplier.

CERTIFIED FOR CANADAAND UNITED STATES USING ANSI/CSAMETHODS.

$10.00

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

Decorative Product: Not for use as a heating appliance.

BARRIER

CONFORMS TO AMERICAN NATIONAL STANDARDS: ANSI Z21.50, CERTIFIED TO CANADIAN CSA2.22 FOR VENTED GAS FIREPLACES.

HDX35

LOG BURNER

ASSEMBLY

B35NL

NATURAL GAS

B35PL

PROPANE

This burner and log assembly are approved for use in the HDX35 gas ﬁreplace only. They are not approved for

use as a stand alone appliance or in conjunction with any other appliance.

1.0 GENERAL INFORMATION

2.0 INSTALLATION

2.1 ACCESS PANEL

1.0 GENERAL INFORMATION 2

2.0 INSTALLATION 2

2.1 ACCESS PANEL 2

2.2 AIR ADJUSTMENT ROD INSTALLATION 3

2.3 BURNER ASSEMBLY 3

2.4 BULKHEADS 4

2.5 HEARTH PANEL INSTALLATION 5

2.6 HEARTH LOG & LOG PLACEMENT 6

2.7 CHARCOAL LUMPS 7

2.8 CHARCOAL EMBERS 7

2.9 VERMICULITE 7

2.10 GLOWING EMBERS 7

3.0 ADJUSTMENT 8

3.1 FLAME CHARACTERISTICS 8

3.2 VENTURI ADJUSTMENT 8

4.0 REPLACEMENTS 9

5.0 HDX35 LOG BURNER 10

INSIDE UNIT OUTSIDE UNIT

A. Remove the door,

refer to installation

instructions.

Remove the 8

securing screws

and lift the plate

up and out of

the appliance.

Gasket will need

to be replaced if

damaged.

W415-1451 / A / 07.21.15

NOTE: Changes, other than editorial, are denoted by a line in the margin.

TABLE OF CONTENTS

A. Attach the burner assembly to the ﬁrebox

base with the 2 screws supplied.

2.2 AIR ADJUSTMENT ROD INSTALLATION

A. Tilt the burner forward lining the air adjustment cable with the hole in the air control rod.

2.3 BURNER ASSEMBLY

W415-1451 / A / 07.21.15

NOTE: Bulkhead covers need to be removed.

A. Connect the main burner gas ﬂex line

and the pilot line to the gas ﬁttings on the

bulkheads located under the valve access

opening.Care must be taken to ensure the

pilot line isn’t damaged and ensuring gas

tight connections are made.

Main

Burner Gas

Connection

Pilot Tube

Gas Connection

Pilot

Electrode

Lead

Bulkhead

2.4 BULKHEADS

Oriﬁce

Venturi

Tube

B. Connect the pilot electrode lead to the

bulkhead matching the 3/16" ﬂag with the

3/16" bulkhead spade. Do the same with the

1/4" spark lead to the 1/4” bulkhead spade.

C. Ensure the venturi tube is over the oriﬁce

before lighting.

D. Check for gas leaks by brushing on a soap

and water solution. Do not use open ﬂame.

E. After leak test has been performed re-install

access panel with gasket.

NOTE: Air shutter adjustment can be made from

outside the ﬁrebox.

W415-1451 / A / 07.21.15

Hearth ﬂoor panel is shipped separate from unit and are included with the mandatory brick panel kits. Due to

the brittle material of the panels, care must be taken not to bend or force them into place.

When shipped, the hearth panels range in varying shades of Sandstone / New Port. During initial use, the

panels will darken temporarily. The appearance of the panels will permanently lighten in color with use.

INSTALL HEARTH FLOOR PANELS ACCORDING TO THE INSTALLATION LEAFLET.

2.5 HEARTH PANEL INSTALLATION

NOTE: It is recommended to remove the grate assembly prior to panel installation.

W415-1451 / A / 07.21.15

2.6 HEARTH LOG & LOG PLACEMENT

NOTE: All logs are stamped with a part number.

A. Push the rear log (W135-0594) back

ﬂush against the rear panel. B. Place the nochtes in the bottom of the

front right log (W135-0598) over the

right grate posts.

C. Place the notches in the bottom of the

front left log (W135-0597) over the left

grate posts.

D. Place the right crossover log (W135-

0595) into the notch in the top of the

right and rear logs.

E. Place the left crossover log (W135-

0593) into the notch in the top of the left

and rear logs.

W415-1451 / A / 07.21.15

2.7 CHARCOAL LUMPS

34.1

Place the lumps in front of the logs in a realistic manner taking care not to block any of the burner ports.

WARNING

CHARCOAL EMBERS, VERMICULITE AND CHARCOAL LUMPS ARE NOT TO BE PLACED ON THE

BURNER.

2.8 CHARCOAL EMBERS

32.1

Randomly place the charcoal embers along the front and sides of the log support tray in a realistic manner.

Fine dust found in the bottom of the bag should not be used.

NOTE: Charcoal embers are not to be placed on the burner.

2.9 VERMICULITE

33.1

Sprinkle vermiculite around the charcoal embers.

NOTE: Vermiculite is not to be placed on the burner.

2.10 GLOWING EMBERS

Tear the embers into pieces and place along the front row of ports covering all of the burner area. Care should

be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the ﬁbre hairs will

glow. The ember material will only glow when exposed to direct ﬂame; however, care should be taken to not

block the burner ports.

Blocked burner ports can cause an incorrect ﬂame pattern, carbon deposits and delayed ignition. Phazer™

logs glow when exposed to direct ﬂame. Use only certiﬁed “glowing embers” and Phazer™ logs available from

your Authorized dealer.

W415-1451 / A / 07.21.15

3.0 ADJUSTMENT

3.1 FLAME CHARACTERISTICS

It’s important to periodically perform a visual check of the pilot and burner ﬂames. Compare them to the

illustration provided. If any ﬂames appear abnormal call a service person.

FLAME MUST ENVELOP

UPPER 3/8” (9.5mm) TO 1/2”

(12.7mm) OF FLAME SENSO

PILOT

BURNER

ELECTRODE

FLAME

SENSOR

3/8” - 1/2”

(9.5mm - 12.7mm)

54.1B

3.2 VENTURI ADJUSTMENT

OPEN

AIR SHUTTER

ADJUSTMENT

CLOSED

Regardless of venturi orientation, closing the air shutter will cause a more yellow ﬂame, but can lead to

carboning. Opening the air shutter will cause a more blue ﬂame, but can cause ﬂame lifting from the burner

ports. The ﬂame may not appear yellow immediately; allow 15 to 30 minutes for the ﬁnal ﬂame colour to be

established.

AIR SHUTTER ADJUSTMENT MUST ONLY BE DONE BY A QUALIFIED INSTALLER!

49.1

W415-1451 / A / 07.21.15

4.0 REPLACEMENTS

Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally

all parts can be ordered through your Authorized dealer / distributor.

FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE

ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

When ordering replacement parts always give the following information:

• Model & Serial Number of appliance

• Installation date of appliance

• Part number

• Description of part

• Finish

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMATION, CONTACT YOUR

AUTHORIZED DEALER. 41.1

FAILURE TO POSITION THE PARTS

IN ACCORDANCE WITH THIS

MANUAL OR FAILURE TO USE ONLY

PARTS SPECIFICALLY APPROVED

WITH THIS APPLIANCE MAY

RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY.

WARNING

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED

REF. NO. PART NUMBER DESCRIPTION

2LOG BURNER ASSEMBLY

B35NL/P

W135-0597 LEFT LOG (GL-697)

W135-0594

W135-0598

W135-0593

W135-0595

FOR REPLACEMENT

PARTS REFER TO:

“B35NL LOG BURNER”

REAR LOG (GL-697)

RIGHT CROSSOVER LOG (GL-697)

RIGHT LOG (GL-697)

LEFT CROSSOVER LOG (GL-697)

GL-697

W415-1451 / A / 07.21.15

42 48

ITEMS MAY NOTAPPEAR EXACTLYAS ILLUSTRATED

REF. NO. PART NUMBER DESCRIPTION

35 STOCKED STOCKED

YES

W010-3469 GRATE ASSEMBLY

W655-0560 LOG SUPPORT W335-0039 PILOT HOOD YES

W455-0070 PILOT ORIFICE #62 (NG) YES

W455-0068 PILOT ORIFICE #35 (LP)

W240-0006 IGNITOR (w/ WIRE) YES

W245-0025 THERMOSENSOR YES

04.23.15

W720-0062 PILOT TUBE (w/ FITTINGS) YES

W010-2863 PILOTASSEMBLY (NG)

W010-2808 PILOTASSEMBLY (LP)

W500-0816 AIR SHUTTER PLATE

W350-0768 AIR SHUTTER HOUSING

W350-0725 PILOT HOUSING

W100-0183 BURNER ASSEMBLY

W456-0031 BURNER ORIFICE #31 (NG)

W456-0049 BURNER ORIFICE #49 (LP) YES

YES

W010-3646 AIR CONTROL CABLE

5.0 HDX35 LOG BURNER

Andere Handbücher für HDX35

Inhaltsverzeichnis

Sprachen:

Andere Napoleon Kamin im Innenbereich Handbücher

Napoleon

Napoleon Luxuria Series Bedienungsanleitung

Napoleon

Napoleon Electric Fireplace EF30 Bedienungsanleitung

Napoleon

Napoleon Manhattan GE38NT-M Bedienungsanleitung

Napoleon

Napoleon EPI3T Leitfaden

Napoleon

Napoleon EPI3 Leitfaden

Napoleon

Napoleon EFL42 Bedienungsanleitung

Napoleon

Napoleon Vittoria GD19N Bedienungsanleitung

Napoleon

Napoleon BGD36CFNTR Bedienungsanleitung

Napoleon

Napoleon ALLURAVISION NEFL32CHS Bedienungsanleitung

Napoleon

Napoleon GD33NR Bedienungsanleitung

Napoleon

Napoleon EPI3 Bedienungsanleitung

Napoleon

Napoleon HD81 Bedienungsanleitung

Napoleon

Napoleon EFL32H Bedienungsanleitung

Napoleon

Napoleon BGD42P Bedienungsanleitung

Napoleon

Napoleon Ascent X Series Bedienungsanleitung

Napoleon

Napoleon BHD4N Bedienungsanleitung

Napoleon

Napoleon LV50N2 Bedienungsanleitung

Napoleon

Napoleon B42NTREA Bedienungsanleitung

Napoleon

Napoleon ZCVF36 Bedienungsanleitung

Napoleon

Napoleon Oakville GDIG3 Series Bedienungsanleitung

Napoleon

Napoleon XIR3N Bedienungsanleitung

Napoleon

Napoleon GL18N Bedienungsanleitung

Napoleon

Napoleon NEFE27-0815W Bedienungsanleitung

Napoleon

Napoleon GD33NR Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch

Regency Fireplace Products

Regency Fireplace Products Pro Series Kurzanleitung