3344
Operation of buttons Operation of buttons
NOTE Temperaturecontol is notavailable
in Fan mode.
TIMER ON Button
10
Press this button to initiate the auto-on
time sequence. Each press will increase
the auto-timed setting in 30 minutes
increments. When the setting time displays
10.0, each press will increase the auto-
timed setting 60 minutes increments.
To cancel the auto-timed program, simply
adjust the auto-on time to 0.0.
TEMP
TEMP
AUTO
COOL
DRY
HEAT
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
FAN
HIGH
MED
LOW
MODE
MODE
FAN SPEED
FAN SPEED
TIMER ON
TIMER ON
ECO
ECO
ON/OFF
ON/OFF
TIMER OFF
TIMER OFF
RESET LOCK
RESET LOCK
1
12
2
4
4
5
5
66
77
8
8
3
3
10
10
9
9
11
11
12
12
13
13
14
14
O
SET TEMPERATURE( F)
O
SET TEMPERATURE( F)
SWING
SWING
SWING
LED
DISPLAY
LED
DISPLAY
CLEAN
AIR
TURBO
TURBO
1
TEMP UP Button
Push this button to increase the indoor temper-
OO
ature setting in 1 F increments to 86 F.
2
TEMP DOWN Button
Push this button to decrease the indoor temper-
OO
ature setting in 1 F increments to 62 F.
3
MODE Button
4
SWING/SWING Button
6
7
5
RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled and
the controller will return to the initial settings.
AUTO
COOL
DRY
HEAT FAN
Used to stop or start horizontal louver move-
ment or set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press. If keep pushing more
than 2 seconds, the louver will swing up and
down automatically.
Press this button to modify the air conditioner
mode in a sequence of following:
NOTE Please do notselect HEAT mode if the
machine you purchasedis cooling only type.
Heat mode isnot supported by the cooling
only appliance.
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
8
9
ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
Used to select the fan speed in four steps:
Auto Low Med High
FAN SPEED Button
11
Used to enter the energy efficient mode.
Under cooling mode, press this button, the
remote controller will adjust the temperature
O
automatically to 75 F, fan speed of Auto to
save energy(but only if the set temperature
O
is less than 75 F). If the set temperature is
OO
between 75 F and 86 F, press the ECO
button, the fan speed will change to Auto,
the set temperature will remain unchanged.
NOTE:
Pressing the TURBO and SLEEP button,
modifying the mode or adjusting the set
O
temperature to less than 75 F will stop
ECO operation.
ECO Button:
Swing Button(applicable to RG51F1)
CLEAN AIR Button(applicable to RG51F3)
Used to stop or start vertical louver
movement and set the desired left/right air
flow direction. The vertical louver changes
6 degree in angle for each press.
RG51F/EU1(This model does
not have clean air button)
Model: RG51F3/EU1 Model : RG51F1/EU1
Disable/Active clean air function. When the
clean air function is initiated, the Ionizer/
Plasma Dust Collector(depending on models)
is energized and will help to remove pollen
and impurities from the air.
NOTE: Press and hold UP and DOWN buttons
together for 3 seconds will alternate the temper-
OO
ature display between the C & F scale.
Under ECO operation, the set temperature
O
should be 75 F or more. it may result in
insufficient cooling. If you feel uncomfortable,
just press the ECO button again to stop it.
