National Instruments GPIB-PCII Bedienungsanleitung

Getting Started with Your

GPIB-PCII/IIA and

the NI-488.2™Software

for MS-DOS/Windows Graphics

Applications

October 1994 Edition

Part Number 320269B-01

National Instruments Corporate Headquarters

6504 Bridge Point Parkway

Austin, TX 78730-5039

(512) 794-0100

Technical support fax: (800) 328-2203

(512) 794-5678

Branch Offices:

Australia (03) 879 9422, Austria (0662) 435986, Belgium 02/757.00.20,

Canada (Ontario) (519) 622-9310, Canada (Québec) (514) 694-8521,

Denmark 45 76 26 00, Finland (90) 527 2321, France (1) 48 14 24 24,

Germany 089/741 31 30, Italy 02/48301892, Japan (03) 3788-1921,

Mexico 95 800 010 0793, Netherlands 03480-33466, Norway 32-84 84 00,

Singapore 2265886, Spain (91) 640 0085, Sweden 08-730 49 70,

Switzerland 056/20 51 51, Taiwan 02 377 1200, U.K. 0635 523545

Limited Warranty

The GPIB-PCII/IIA is warranted against defects in materials and

workmanship for a period of two years from the date of shipment, as

evidenced by receipts or other documentation. National Instruments will, at

its option, repair or replace equipment that proves to be defective during the

warranty period. This warranty includes parts and labor.

The media on which you receive National Instruments software are

warranted not to fail to execute programming instructions, due to defects in

materials and workmanship, for a period of 90 days from date of shipment,

as evidenced by receipts or other documentation. National Instruments will,

at its option, repair or replace software media that do not execute

programming instructions if National Instruments receives notice of such

defects during the warranty period. National Instruments does not warrant

that the operation of the software shall be uninterrupted or error free.

A Return Material Authorization (RMA) number must be obtained from the

factory and clearly marked on the outside of the package before any

equipment will be accepted for warranty work. National Instruments will

pay the shipping costs of returning to the owner parts which are covered by

warranty.

National Instruments believes that the information in this manual is

accurate. The document has been carefully reviewed for technical accuracy.

In the event that technical or typographical errors exist, National

Instruments reserves the right to make changes to subsequent editions of

this document without prior notice to holders of this edition. The reader

should consult National Instruments if errors are suspected. In no event

shall National Instruments be liable for any damages arising out of or

related to this document or the information contained in it.

EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO

WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. CUSTOMER'S RIGHT TO RECOVER DAMAGES

CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF NATIONAL

INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE

PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE

LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA, PROFITS,

USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES,

EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the

liability of National Instruments will apply regardless of the form of action,

whether in contract or tort, including negligence. Any action against

National Instrument must be brought within one year after the cause of

action accrues. National Instruments shall not be liable for any delay in

performance due to causes beyond its reasonable control. The warranty

provided herein does not cover damages, defects, malfunctions, or service

failures caused by owner's failure to follow the National Instruments

installation, operation, or maintenance instructions; owner's modification of

the product; owner's abuse, misuse, or negligent acts; and power failure or

surges, fire, flood, accident, actions of third parties, or other events outside

reasonable control.

Under the copyright laws, this book may not be copied, photocopied,

reproduced, or translated, in whole or in part, without the prior written

consent of National Instruments Corporation.

Trademarks

NAT4882®and NI-488.2™are trademarks of National Instruments

Corporation.

Product and company names listed are trademarks or trade names of their

respective companies.

WARNING REGARDING MEDICAL AND

CLINICAL USE OF NATIONAL

INSTRUMENTS PRODUCTS

National Instruments products are not designed with components and testing

intended to ensure a level of reliability suitable for use in treatment and

diagnosis of humans. Applications of National Instruments products

involving medical or clinical treatment can create a potential for accidental

injury caused by product failure, or by errors on the part of the user or

application designer. Any use or application of National Instruments

products for or involving medical or clinical treatment must be performed by

properly trained and qualified medical personnel, and all traditional medical

safeguards, equipment, and procedures that are appropriate in the particular

situation to prevent serious injury or death should always continue to be

used when National Instruments products are being used. National

Instruments products are NOT intended to be a substitute for any form of

established process, procedure, or equipment used to monitor or safeguard

human health and safety in medical or clinical treatment.

FCC/DOC Radio Frequency

Interference Compliance

This equipment generates and uses radio frequency energy and, if not

installed and used in strict accordance with the instructions in this manual,

may cause interference to radio and television reception. This equipment

has been tested and found to comply with the following two regulatory

agencies:

Federal Communications Commission

This device complies with Part 15 of the Federal Communications

Commission (FCC) Rules for a Class B digital device. A Class B device is

distinguishable from a Class A device by the appearance of an FCC ID

number located on the Class B device.

Canadian Department of Communications

This device complies with the limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications (DOC).

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de classe B

prescrites dans le règlement sur le brouillage radioélectrique édicté par le

ministère des communications du Canada.

Instructions to Users

These regulations are designed to provide reasonable protection against

interference from the equipment to radio and television reception in

residential areas.

There is no guarantee that interference will not occur in a particular

installation. However, the chances of interference are much less if the

equipment is installed and used according to this instruction manual.

If the equipment does cause interference to radio or television reception,

which can be determined by turning the equipment on and off, one or more

of the following suggestions may reduce or eliminate the problem.

• Operate the equipment and the receiver on different branches of your

AC electrical system.

• Move the equipment away from the receiver with which it is interfering.

• Reorient or relocate the receiver’s antenna.

• Be sure that the equipment is plugged into a grounded outlet and that

the grounding has not been defeated with a cheater plug.

Notice to user: Changes or modifications not expressly approved by

National Instruments could void the user’s authority to

operate the equipment under the FCC Rules.

If necessary, consult National Instruments or an experienced radio/television

technician for additional suggestions. The following booklet prepared by

the FCC may also be helpful: How to Identify and Resolve Radio-TV

Interference Problems. This booklet is available from the U.S. Government

Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4.

Contents

About This Manual ..........................................................................xiii

Organization of This Manual......................................................xiii

Conventions Used in This Manual.............................................xiv

Related Documentation ..............................................................xv

Customer Communication..........................................................xv

Chapter 1

Introduction and Hardware Installation.................................1-1

What You Need to Get Started...................................................1-1

Optional Equipment....................................................................1-2

Hardware Description.................................................................1-2

Software Description..................................................................1-3

Installing the GPIB-PCII/IIA .....................................................1-3

Chapter 2

NI-488.2 Software Files...................................................................2-1

NI-488.2 Software Programs and Files for MS-DOS.................2-1

NI-488.2 Software Programs and Files for Windows ...............2-2

Chapter 3

Software Installation .......................................................................3-1

Installing the NI-488.2 Software for MS-DOS...........................3-1

Step 1. Run INSTALL...............................................3-1

Step 2. Test the Software Installation ........................3-2

Installing the NI-488.2 Software for Windows ..........................3-3

Step 1. Run INSTALL...............................................3-3

Step 2. Set Up the Windows Applications.................3-4

Step 3. Test the Software Installation ........................3-5

Appendix A

Hardware Specifications................................................................A-1

Appendix B

Changing Board and Device Characteristics.........................B-1

Board and Device Characteristics...............................................B-1

Characteristics of the Graphics Devices.......................B-1

Characteristics of Each GPIB-PCII/IIA ......................B-2

Contents

GPIB-PCII/IIA for Graphics x © National Instruments Corp.

Default Configurations...............................................................B-2

Primary Default Characteristics...................................B-3

Repeat Addressing (Device Characteristic Only) ........B-4

Changing Board and Device Characteristics..............................B-4

Changing Characteristics for MS-DOS........................B-4

Running IBCONF..........................................B-4

Changing Characteristics for Windows .......................B-5

Running WIBCONF ......................................B-5

Appendix C

Hardware and Software Configuration...................................C-1

Verifying the GPIC-PC Mode Setting........................................C-2

Verifying the Hardware Configuration Settings.........................C-3

Changing Hardware Configuration Settings...............................C-4

Step 1. Configure the Hardware.................................C-4

Base I/O Address Selection...........................C-4

GPIC-PCII Mode.............................C-5

GPIC-PCIIA Mode..........................C-7

Possible Conflicts............................C-9

Interrupt Selection .........................................C-11

Shared Interrupts in GPIC-PCIIA

Mode................................................C-12

Possible Conflicts............................C-16

DMA Channel Selection................................C-17

Possible Conflicts............................C-19

Shield Ground Configuration.........................C-19

Step 2. Run the IBDIAG Diagnostic Program...........C-20

Step 3. Configure the Software..................................C-20

Configuring the Software for MS-DOS.........C-21

Configuring the Software for Windows.........C-22

Appendix D

Interactive Software Installation................................................D-1

INSTALL for MS-DOS..............................................................D-1

Installing the Software for MS-DOS ...........................D-2

Running IBDIAG for MS-DOS...................................D-3

Exiting INSTALL ........................................................D-3

INSTALL for Windows .............................................................D-4

Installing the Software for Windows ...........................D-4

Running IBDIAG for Windows...................................D-5

Exiting INSTALL ........................................................D-5

Contents

Appendix E

Customer Communication............................................................E-1

Glossary.................................................................................................G-1

Figures

Figure 1-1. Installing the GPIB-PCII/IIA...........................................1-4

Figure C-1. GPIC-PCII/IIA Parts Locator Diagram...........................C-1

Figure C-2. GPIC-PC Mode Selection Settings..................................C-2

Figure C-3. Base I/O Address Switch Settings for GPIC-PCII

Mode................................................................................C-6

Figure C-4. Base I/O Address Switch Settings for GPIC-PCIIA

Mode................................................................................C-7

Figure C-5. Default Interrupt Jumper Setting for GPIC-PCII Mode ..C-12

Figure C-6. Default Interrupt Jumper Setting for GPIC-PCIIA

Mode................................................................................C-13

Figure C-7. Interrupt Jumper Settings for GPIC-PCIIA Mode...........C-14

Figure C-8. DMA Channel Jumper Setting for DMA Channel 1.......C-18

Figure C-9. Ground Configuration Jumper Settings...........................C-20

Tables

Table A-1. Electrical Characteristics.................................................A-1

Table A-2. Environmental Characteristics.........................................A-1

Table A-3. Physical Characteristics...................................................A-2

Table C-1. Factory Default Settings and Available Configurations

for GPIC-PCII Mode .......................................................C-3

Table C-2. Factory Default Settings and Available Configurations

for GPIC-PCIIA Mode.....................................................C-3

Table C-3. I/O Addresses Used by Other Devices.............................C-10

Table C-4. Interrupt Levels Used by Other Devices .........................C-16

Table C-5. DMA Channels for the GPIC-PCII/IIA...........................C-18

About This Manual

This manual contains instructions for installing and configuring the

National Instruments GPIB-PCII/IIA interface board and the NI-488.2

software handler for MS-DOS/Windows graphics applications.

Organization of This Manual

This manual is organized as follows:

• Chapter 1, Introduction and Hardware Installation, lists what you need

to get started and optional equipment you can order, gives a brief

description of the hardware and the NI-488.2 software, and contains

instructions for installing your GPIB-PCII/IIA.

• Chapter 2, NI-488.2 Software Files, describes the software files

contained on your NI-488.2 distribution diskette.

• Chapter 3, Software Installation, contains instructions for installing the

NI-488.2 software files.

• Appendix A, Hardware Specifications, describes the electrical,

environmental, and physical characteristics of the GPIB-PCII/IIA and

the recommended operating conditions.

• Appendix B, Changing Board and Device Characteristics, contains

instructions for changing the default board and device characteristics of

the NI-488.2 handler for MS-DOS/Windows.

• Appendix C, Hardware and Software Configuration,contains

instructions for changing the configuration settings of your

GPIB-PCII/IIA.

• Appendix D, Interactive Software Installation, contains instructions for

running the interactive version of INSTALL.

• Appendix E, Customer Communication, contains forms you can use to

request help from National Instruments or to comment on our products

and manuals.

Andere Handbücher für GPIB-PCII

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Computerhardware Handbücher

National Instruments

National Instruments NI PXIe-8130 Bedienungsanleitung

National Instruments

National Instruments NI PXI-8221 Bedienungsanleitung

National Instruments

National Instruments Network Adapter NI PXIe-1075 Bedienungsanleitung

National Instruments

National Instruments Data Acquisition Device NI USB-621x Bedienungsanleitung

National Instruments

National Instruments 9260 Bedienungsanleitung

National Instruments

National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Bedienungsanleitung

National Instruments

National Instruments sbRIO-9607 Bedienungsanleitung

National Instruments

National Instruments USB-6501 Bedienungsanleitung

National Instruments

National Instruments NI 6612 Bedienungsanleitung

National Instruments

National Instruments PCI-1407 Bedienungsanleitung

National Instruments

National Instruments Compact FieldPoint Mounting Accessories... Bedienungsanleitung

National Instruments

National Instruments GPIB-ENET-1000 Bedienungsanleitung

National Instruments

National Instruments MXIbus VME-AT2000 Bedienungsanleitung

National Instruments

National Instruments DAQPad-6020E Bedienungsanleitung

National Instruments

National Instruments VXI-AT2000 Bedienungsanleitung

National Instruments

National Instruments NI 9472 Bedienungsanleitung

National Instruments

National Instruments PXI Express PXIe-1075 Bedienungsanleitung

National Instruments

National Instruments GPIB-PCIIB Bedienungsanleitung

National Instruments

National Instruments NI-9260 Bedienungsanleitung

National Instruments

National Instruments ExpressCard Strain-Relief Bedienungsanleitung

National Instruments

National Instruments AT-GPIB Bedienungsanleitung

National Instruments

National Instruments NI 5401 Bedienungsanleitung

National Instruments

National Instruments NI PXIe-8105 Bedienungsanleitung

National Instruments

National Instruments Multifunction RIO PXI-7830 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung