National Instruments NI 9209 Handbuch

CALIBRATION PROCEDURE

NI 9209

16-Channel Differential/32-Channel Single-Ended, ±10 V, 24-Bit

Analog Input Module

This document contains the verification and adjustment procedures for the NI 9209. For more

information about calibration solutions, visit ni.com/calibration.

Contents

Software.................................................................................................................................... 1

Documentation.......................................................................................................................... 2

Test Equipment......................................................................................................................... 3

Test Conditions......................................................................................................................... 3

Initial Setup............................................................................................................................... 3

Verification ............................................................................................................................... 4

Differential Voltage Accuracy Verification ..................................................................... 4

Single-Ended Voltage Accuracy Verification .................................................................. 6

Adjustments .............................................................................................................................. 7

Voltage Accuracy Adjustment.......................................................................................... 7

EEPROM Update ..................................................................................................................... 8

Reverification ........................................................................................................................... 8

Accuracy Under Calibration Conditions .................................................................................. 9

Worldwide Support and Services ............................................................................................. 9

Software

Calibrating the NI 9209 requires the installation of NI-DAQmx 15.1 or later on the calibration

system. You can download NI-DAQmx from ni.com/downloads. NI-DAQmx supports

LabVIEW, LabWindows™/CVI™, C/C++, C#, and Visual Basic .NET. When you install

NI-DAQmx you only need to install support for the application software that you intend to use.

2|ni.com |NI 9209 Calibration Procedure

Documentation

Consult the following documents for information about the NI 9209, NI-DAQmx, and your

application software. All documents are available on ni.com and help files install with the

software.

NI cDAQ-9174/9178 USB Chassis Quick Start

NI-DAQmx installation and hardware setup

NI 9209 Getting Started Guide

NI 9209 specific information.

NI 9209 Datasheet

NI 9209 specifications and calibration interval.

NI DAQmx Help

Information about creating applications that use the NI-DAQmx driver

LabVIEW Help

LabVIEW programming concepts and reference information about NI-DAQmx

VIs and functions

NI-DAQmx C Reference Help

Reference information for NI-DAQmx C functions and NI-DAQmx C properties

NI-DAQmx .NET Help Support for Visual Studio

Reference information for NI-DAQmx .NET methods and NI-DAQmx .NET

properties, key concepts, and a C enum to .NET enum mapping table

NI 9209 Calibration Procedure |© National Instruments |3

Test Equipment

Table 1 lists the equipment recommended for the performance verification and adjustment

procedures. If the recommended equipment is not available, select a substitute using the

requirements listed in Table 1.

Test Conditions

The following setup and environmental conditions are required to ensure the NI 9209 meets

published specifications.

• Keep connections to the device as short as possible. Long cables and wires act as antennas,

picking up extra noise that can affect measurements.

• Verify that all connections to the device are secure.

• Use shielded copper wire for all cable connections to the device. Use twisted-pairs wire to

eliminate noise and thermal offsets.

• Maintain an ambient temperature of 23 ± 5 °C. The device temperature will be greater than

the ambient temperature.

• Keep relative humidity below 80%.

• Allow a warm-up time of at least 10 minutes to ensure that the NI 9209 measurement

circuitry is at a stable operating temperature.

Initial Setup

Complete the following steps to set up the NI 9209.

1. Install NI-DAQmx.

2. Make sure the NI cDAQ-9178 power source is not connected.

3. Install the module in slot 8 of the NI cDAQ-9178 chassis. Leave slots 1 through 7 of the

NI cDAQ-9178 chassis empty.

4. Connect the NI cDAQ-9178 chassis to your host computer.

5. Connect the power source to the NI cDAQ-9178 chassis.

Table 1. Recommended Equipment

Equipment

Recommended

Model Minimum Requirements

Source Fluke 5500A Use a source with gain error ≤260 ppm and an

offset error ≤70 uV.

cDAQ Chassis NI cDAQ-9178 —

Connection

Accessory

NI 9923 —

4|ni.com |NI 9209 Calibration Procedure

6. Launch Measurement & Automation Explorer (MAX).

7. Right-click the device name and select Self-Test to ensure that the module is working

properly.

Verification

The following performance verification procedures describe the sequence of operation and test

points required to verify the NI 9209 and assumes that adequate traceable uncertainties are

available for the calibration references.

Differential Voltage Accuracy Verification

Complete the following procedure to determine the As-Found status of the NI 9209.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9209 to the calibrator as shown in Figure 1.

Figure 1. Differential Voltage Accuracy Connections

Note If the calibrator outputs are truly floating, connect the negative output to a

quiet earth ground as well as COM to give the entire system a ground reference.

3. Set the calibrator voltage to a Test Point value indicated in Table 4.

4. Set the calibrator to Operate mode (OPR).

5. Acquire and average samples.

a. Create and configure an AI voltage task on the NI 9209 according to Table 2.

1 Connections when using a calibrator with a guard connection.

2 Connections when using a calibrator with no guard connection.

Table 2. NI 9209 Configuration for Voltage Accuracy Verification

Input Range

Scaled Units Terminal ConfigurationMin Max

-10 10 Volts Differential

NI 9209Calibrator

AIx–

AIx+

COM

Guard

NI 9209Calibrator

AIx–

AIx+

COM

NI 9209 Calibration Procedure |© National Instruments |5

b. Configure the AI voltage task according to Table 3. Set the ADC timing mode to

high-resolution.

c. Start the task.

d. Average the readings.

e. Stop and clear the task.

6. Compare the average to the limits in Table 4.

Note The test limits listed in Table 4 are derived using the values in Table 8.

Note The uncertainty of the calibration standard is not included in these limits.

7. Repeat step 5 and 6 with the ADC timing mode on the NI 9209 set to high-speed.

8. Set the calibrator to Standby mode (STBY).

9. Repeat steps 3 through 8 for each test point listed in Table 4.

10. Disconnect the calibrator from the device.

11. Repeat steps 1 through 10 for each voltage channel on the NI 9209.

Table 3. NI 9209 Voltage Timing Configuration

ADC Timing

Mode Sample Mode Samples to Read Sample Rate

High-Resolution N Samples 519 S/s

High-Speed N Samples 75 500 S/s

Table 4. NI 9209 Verification Test Limits for Differential Voltage Accuracy

Range (V) Test Point 2-Year Limits

Minimum Maximum Location

Value

(V)

Lower Limit

(V)

Upper Limit

(V)

-10.00000 10.00000 Pos FS 10.00000 9.98972 10.01028

-10.00000 10.00000 Mid 0.00000 -0.00058 0.00058

-10.00000 10.00000 Neg FS -10.00000 -10.01028 -9.98972

6|ni.com |NI 9209 Calibration Procedure

Single-Ended Voltage Accuracy Verification

Complete the following procedure to determine the As-Found status of the NI 9209.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9209 to the calibrator as shown in Figure 2.

Figure 2. Single-Ended Voltage Accuracy Connections

Note If the calibrator outputs are truly floating, connect the negative output to a

quiet earth ground as well as COM to give the entire system a ground reference.

3. Set the calibrator voltage to a Test Point value indicated in Table 6.

4. Set the calibrator to Operate mode (OPR).

5. Acquire and average samples.

a. Create and configure an AI voltage task on the NI 9209 according to Table 5.

b. Configure the AI voltage task according to Table 3 on page 5. Set the ADC timing

mode to high-resolution.

c. Start the task.

d. Average the readings.

e. Clear the task.

1 Connections when using a calibrator with a guard connection.

2 Connections when using a calibrator with no guard connection.

Table 5. NI 9209 Configuration for Voltage Accuracy Verification

Input Range

Scaled Units Terminal ConfigurationMin Max

-10 10 Vo l t s Single-Ended/RSE

NI 9209Calibrator

COM

AIx

Guard

NI 9209Calibrator

COM

AIx

1 2

NI 9209 Calibration Procedure |© National Instruments |7

6. Compare the average to the limits in Table 6.

Table 6. NI 9209 Verification Test Limits for Single-Ended Voltage Accuracy

Note The test limits listed in Table 6 are derived using the values in Table 8.

Note The uncertainty of the calibration standard is not included in these limits.

7. Repeat step 5 and 6 with the ADC timing mode on the NI 9209 set to high-speed.

8. Set the calibrator to Standby mode (STBY).

9. Repeat steps 3 through 8 for each test point listed in Table 6.

10. Disconnect the calibrator from the device.

11. Repeat steps 1 through 10 for each voltage channel on the NI 9209.

Adjustments

The following performance adjustment procedures describe the sequence of operation required

to adjust the NI 9209.

Voltage Accuracy Adjustment

Complete the following procedure to adjust the voltage accuracy performance of the NI 9209.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9209 to the calibrator as shown in Figure 1.

3. Adjust the NI 9209 voltage accuracy.

a. Initialize a calibration session on the NI 9209. The default password is NI.

b. Input the external temperature in degrees Celsius.

c. Call the DAQmx Get 9209 Calibration Adjustment Points function to obtain an array

of recommended calibration voltages for the NI 9209.

d. Set the calibrator to a reference value determined by the array of recommended

calibration voltages.

e. Set the calibrator to Operate mode (OPR).

Range (V) Test Point 2-Year Limits

Minimum Maximum Location

Value

(V)

Lower Limit

(V)

Upper Limit

(V)

-10.00000 10.00000 Pos FS 10.00000 9.99014 10.00986

-10.00000 10.00000 Mid 0.00000 -0.00056 0.00056

-10.00000 10.00000 Neg FS -10.00000 -10.00986 -9.99014

8|ni.com |NI 9209 Calibration Procedure

f. Call and configure the NI 9209 gain instance of the adjustment function according to

Table 7 with the input terminal configuration set to Differential.

g. Set the calibrator to Standby mode (STBY).

h. Repeat steps d through g for each calibration voltage in the array.

i. Repeat steps d through h for each channel.

j. Repeat steps d through i with the input terminal configuration set to

Single-Ended/RSE as shown in Figure 2.

k. Disconnect the calibrator from the NI 9209.

l. Short the voltage channels to the NI 9209 AIGND.

m. Call the DAQmx Adjust 9209 Offset Calibration for the physical channel(s) adjusted

in the RSE and Differential sections. For example, if you adjusted all the channels,

then the physical channels should be cDAQ1Mod8/ai0:31.

Note If adjusting the channel(s) in differential and single-ended mode, the physical

channel(s) should be a union of the channels specified in both configurations.

n. Close and commit the calibration session.

4. Remove the connections from the NI 9209.

EEPROM Update

When an adjustment procedure is completed, the NI 9209 internal calibration memory

(EEPROM) is immediately updated.

If you do not want to perform an adjustment, you can update the calibration date and onboard

calibration temperature without making any adjustments by initializing an external calibration,

setting the C Series calibration temperature, and closing the external calibration.

Reverification

Repeat the Verification section to determine the As-Left status of the device.

Note If any test fails Reverification after performing an adjustment, verify that you

have met the Test Conditions before returning your device to NI. Refer to Worldwide

Support and Services for assistance in returning the device to NI.

Table 7. Gain Adjustment Configuration

Physical Channel Reference Value

cDAQMod8/aixThe reference value from the array of adjustment points

NI 9209 Calibration Procedure |© National Instruments |9

Accuracy Under Calibration Conditions

The values in the following table are based on calibrated scaling coefficients, which are stored

in the onboard EEPROM.

The following accuracy table is valid for calibration under the following conditions:

• Ambient temperature 23 °C ± 5 °C

• NI 9209 installed in slot 8 of an NI cDAQ-9178 chassis

• Slots 1 through 7 of the NI cDAQ-9178 chassis are empty

Note For operational specifications, refer to the most recent NI 9209 Datasheet

online at ni.com/manuals.

Worldwide Support and Services

The National Instruments website is your complete resource for technical support. At ni.com/

support you have access to everything from troubleshooting and application development

self-help resources to email and phone assistance from NI Application Engineers.

Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and

other services.

Visit ni.com/register to register your National Instruments product. Product registration

facilitates technical support and ensures that you receive important information updates from NI.

National Instruments corporate headquarters is located at 11500 North Mopac Expressway,

Austin, Texas, 78759-3504. National Instruments also has offices located around the world. For

telephone support in the United States, create your service request at ni.com/support or dial

1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the

Worldwide Offices section of ni.com/niglobal to access the branch office websites, which

provide up-to-date contact information, support phone numbers, email addresses, and current

events.

Table 8. NI 9209 Accuracy Under Calibration Conditions

Input Channels Percentage of Reading Percentage of Range*

Differential 0.097% 0.0055%

Single-Ended 0.093% 0.0053%

* Range equals 10.4 V for voltage.

376908B-01 Jul16

Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on National Instruments trademarks. Other

product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National

Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the

National Instruments Patents Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party

legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance

for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES

NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR

ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

Andere Handbücher für NI 9209

Inhaltsverzeichnis

Andere National Instruments Steuereinheit Handbücher

National Instruments

National Instruments SCXI-1120/D Handbuch

National Instruments

National Instruments PXIe-8238 Bedienungsanleitung

National Instruments

National Instruments NI USB-9201 Bedienungsanleitung

National Instruments

National Instruments SCXI-1160 Bedienungsanleitung

National Instruments

National Instruments 9775 Handbuch

National Instruments

National Instruments SCXI-1000 Bedienungsanleitung

National Instruments

National Instruments SCXI-1104 Bedienungsanleitung

National Instruments

National Instruments NI 9512 Bedienungsanleitung

National Instruments

National Instruments PXIe-8861 Bedienungsanleitung

National Instruments

National Instruments SCC-DO01 Bedienungsanleitung

National Instruments

National Instruments SCXI-1502 Bedienungsanleitung

National Instruments

National Instruments NI DCM-23 Series Bedienungsanleitung

National Instruments

National Instruments 9266 Bedienungsanleitung

National Instruments

National Instruments SCC-CTR01 Bedienungsanleitung

National Instruments

National Instruments PXIe-5693 Handbuch

National Instruments

National Instruments NI 9381 Bedienungsanleitung

National Instruments

National Instruments NI 9269 Bedienungsanleitung

National Instruments

National Instruments NI 9870 Bedienungsanleitung

National Instruments

National Instruments NI 9251 Bedienungsanleitung

National Instruments

National Instruments 9756 Bedienungsanleitung

National Instruments

National Instruments Network Adapter NI PXIe-6672 Bedienungsanleitung

National Instruments

National Instruments 9477 Bedienungsanleitung

National Instruments

National Instruments NI 9203 Handbuch

National Instruments

National Instruments VXI-8340 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung