National Instruments NI 9426 Bedienungsanleitung
NI-9426 Getting
Started
2022-07-06
Contents
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Guidelines for Hazardous Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety Guidelines for Hazardous Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Special Conditions for Marine Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
NI 9426 Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connecting a Sinking-Output Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Where to Go Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
NI Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ni.com
2
NI-9426 Getting Started
Before You Begin
Read the NI-9426 Safety, Environmental, and Regulatory Information and
complete the soware and hardware installation procedures in your chassis
documentation.
Safety Guidelines
Caution Observe all instructions and cautions in the user documentation.
Using the product in a manner not specified can damage the product and
compromise the built-in safety protection.
Attention Suivez toutes les instructions et respectez toutes les mises
en garde de la documentation d'utilisation. L'utilisation du produit de
toute autre façon que celle spécifiée risque de l'endommager et de
compromettre la protection de sécurité intégrée.
Safety Voltages
Connect only voltages that are within the following limits:
Vsup-to-channel 30 VDC maximum
Isolation
Channel-to-channel None
Channel-to-earth ground
Continuous 60 VDC, Measurement Category I
Withstand 1,000 Vrms, verified by a 5 s dielectric withstand test
© National Instruments 3
NI-9426 Getting Started
Measurement Category I
Caution Do not connect the product to signals or use for measurements
within Measurement Categories II, III, or IV.
Attention Ne pas connecter le produit à des signaux dans les catégories
de mesure II, III ou IV et ne pas l'utiliser pour eectuer des mesures dans
ces catégories.
Warning Do not connect the product to signals or use for measurements
within Measurement Categories II, III, or IV, or for measurements on MAINs
circuits or on circuits derived from Overvoltage Category II, III, or IV which
may have transient overvoltages above what the product can withstand.
The product must not be connected to circuits that have a maximum
voltage above the continuous working voltage, relative to earth or to
other channels, or this could damage and defeat the insulation. The
product can only withstand transients up to the transient overvoltage
rating without breakdown or damage to the insulation. An analysis of
the working voltages, loop impedances, temporary overvoltages, and
transient overvoltages in the system must be conducted prior to making
measurements.
Mise en garde Ne pas connecter le produit à des signaux dans les
catégories de mesure II, III ou IV et ne pas l'utiliser pour des mesures dans
ces catégories, ou des mesures sur secteur ou sur des circuits dérivés de
surtensions de catégorie II, III ou IV pouvant présenter des surtensions
transitoires supérieures à ce que le produit peut supporter. Le produit
ne doit pas être raccordé à des circuits ayant une tension maximale
supérieure à la tension de fonctionnement continu, par rapport à la
terre ou à d'autres voies, sous peine d'endommager et de compromettre
l'isolation. Le produit peut tomber en panne et son isolation risque
d'être endommagée si les tensions transitoires dépassent la surtension
transitoire nominale. Une analyse des tensions de fonctionnement, des
ni.com
4
NI-9426 Getting Started
impédances de boucle, des surtensions temporaires et des surtensions
transitoires dans le système doit être eectuée avant de procéder à des
mesures.
Measurement Category I is for measurements performed on circuits not directly
connected to the electrical distribution system referred to as MAINS voltage. MAINS
is a hazardous live electrical supply system that powers equipment. This category is
for measurements of voltages from specially protected secondary circuits. Such
voltage measurements include signal levels, special equipment, limited-energy
parts of equipment, circuits powered by regulated low-voltage sources, and
electronics.
Note Measurement Categories CAT I and CAT O are equivalent. These test
and measurement circuits are for other circuits not intended for direct
connection to the MAINS building installations of Measurement Categories
CAT II, CAT III, or CAT IV.
Safety Guidelines for Hazardous Voltages
Caution Ensure that hazardous voltage wiring is performed only by
qualified personnel adhering to local electrical standards.
Caution Do not mix hazardous voltage circuits and human-accessible
circuits on the same module.
Caution Ensure that devices and circuits connected to the module are
properly insulated from human contact.
Caution When module terminals are hazardous voltage LIVE (>42.4 Vpk/60
V DC), you must ensure that devices and circuits connected to the module
are properly insulated from human contact.
© National Instruments 5
NI-9426 Getting Started
Safety Guidelines for Hazardous Locations
The NI-9426 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous
locations; Class I, Zone 2, AEx nA IIC T4 Gc and Ex nA IIC T4 Gc hazardous locations;
and nonhazardous locations only. Follow these guidelines if you are installing the
NI-9426 in a potentially explosive environment. Not following these guidelines may
result in serious injury or death.
Caution Do not disconnect I/O-side wires or connectors unless power has
been switched o or the area is known to be nonhazardous.
Caution Do not remove modules unless power has been switched o or
the area is known to be nonhazardous.
Caution Substitution of components may impair suitability for Class I,
Division 2, or Zone 2.
Caution The system must be installed in an enclosure certified for the
intended hazardous (classified) location, having a tool secured cover/door,
where a minimum protection of at least IP54 is provided.
Special Conditions for Hazardous Locations Use in Europe and
Internationally
The NI-9426 has been evaluated as Ex nA IIC T4 Gc equipment under
DEMKO 07ATEX 0626664X and is IECEx UL 14.0089X certified. Each NI-9426 is marked
II 3G and is suitable for use in Zone 2 hazardous locations, in ambient
temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI-9426 in Gas Group IIC
hazardous locations, you must use the device in an NI chassis that has been
evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.
ni.com
6
NI-9426 Getting Started
Caution Transient protection shall be provided that is set at a level not
exceeding 140% of the peak rated voltage value of 85 V at the supply
terminals to the equipment.
Caution The system shall only be used in an area of not more than
Pollution Degree 2, as defined in IEC/EN 60664-1.
Caution The system shall be mounted in an ATEX/IECEx-certified
enclosure with a minimum ingress protection rating of at least IP54 as
defined in IEC/EN 60079-15.
Caution The enclosure must have a door or cover accessible only by the
use of a tool.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits
for electromagnetic compatibility (EMC) stated in the product specifications. These
requirements and limits provide reasonable protection against harmful interference
when the product is operated in the intended operational electromagnetic
environment.
This product is intended for use in industrial locations. However, harmful
interference may occur in some installations, when the product is connected to a
peripheral device or test object, or if the product is used in residential or
commercial areas. To minimize interference with radio and television reception and
prevent unacceptable performance degradation, install and use this product in strict
accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved
by National Instruments could void your authority to operate it under your local
regulatory rules.
© National Instruments 7
NI-9426 Getting Started
Special Conditions for Marine Applications
Some products are approved for marine (shipboard) applications. To verify marine
approval certification for a product, visit ni.com/product-certifications, search by
model number, and click the appropriate link.
Notice In order to meet the EMC requirements for marine applications,
install the product in a shielded enclosure with shielded and/or filtered
power and input/output ports. In addition, take precautions when
designing, selecting, and installing measurement probes and cables to
ensure that the desired EMC performance is attained.
Preparing the Environment
Ensure that the environment in which you are using the NI-9426 meets the following
specifications.
Operating temperature (IEC 60068-2-1, IEC 60068-2-2) -40 °C to 70 °C
Operating humidity (IEC 60068-2-78) 10% RH to 90% RH, noncondensing
Pollution Degree 2
Maximum altitude 2,000 m
Indoor use only.
Note Refer to the device datasheet on ni.com/manuals for complete
specifications.
NI 9426 Pinout
ni.com
8
NI-9426 Getting Started
DI16
DI17
DI18
DI19
DI20
DI21
DI22
DI23
Vsup
Vsup
DI24
DI25
DI26
DI27
DI28
DI29
DI30
DI31
DI0
DI1
DI2
DI3
DI4
DI5
DI6
DI7
Vsup
Vsup
DI8
DI9
DI10
DI11
DI12
DI13
DI14
DI15
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Signal Description
DI Digital input signal connection
NC No connection
Vsup Voltage supply connection
Table 1. Signal Descriptions
Connecting a Sinking-Output Device
You can connect 2- and 3-wire sinking-output devices to the NI-9426.
NI 9426
+
_DI
Vsup
Sinking-Output
Device
External
Power
Supply
The NI-9426 channel registers as ON when the sinking-output device drives the
input below Vsup and meets the input ON range. If no device is connected to DI, the
channel registers as OFF.
Where to Go Next
© National Instruments 9
NI-9426 Getting Started
NI Services
Visit ni.com/support to find support resources including documentation,
downloads, and troubleshooting and application development self-help such as
tutorials and examples.
Visit ni.com/services to learn about NI service oerings such as calibration options,
repair, and replacement.
Visit ni.com/register to register your NI product. Product registration facilitates
technical support and ensures that you receive important information updates from
NI.
NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX,
78759-3504, USA.
ni.com
10
NI-9426 Getting Started
© 2022 National Instruments Corporation.
Andere Handbücher für NI 9426
2
Inhaltsverzeichnis
Andere National Instruments Steuereinheit Handbücher
National Instruments
National Instruments 7340 PCI Bedienungsanleitung
National Instruments
National Instruments FP-AI-102 Bedienungsanleitung
National Instruments
National Instruments Module SCXI-1125 Handbuch
National Instruments
National Instruments FieldPoint FP-1001 Bedienungsanleitung
National Instruments
National Instruments PC/104-GPIB Bedienungsanleitung
National Instruments
National Instruments NI-9244 Bedienungsanleitung
National Instruments
National Instruments FieldPoint FP-1001 Bedienungsanleitung
National Instruments
National Instruments BNC-208X Series Bedienungsanleitung
National Instruments
National Instruments NI 6520 Bedienungsanleitung
National Instruments
National Instruments NI 9269 Bedienungsanleitung
National Instruments
National Instruments NI 9401 Bedienungsanleitung
National Instruments
National Instruments NI 9246 Bedienungsanleitung
National Instruments
National Instruments NI 9881 Bedienungsanleitung
National Instruments
National Instruments NI 9474 Bedienungsanleitung
National Instruments
National Instruments SCC-DO01 Bedienungsanleitung
National Instruments
National Instruments NI PXI/e-4000 Series Bedienungsanleitung
National Instruments
National Instruments 9266 Bedienungsanleitung
National Instruments
National Instruments PXIe-8521 Bedienungsanleitung
National Instruments
National Instruments PXIe-5693 Handbuch
National Instruments
National Instruments PXIe-8238 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
