National Instruments SCXI-1181K Bedienungsanleitung

371063A-01 © 1994 National Instruments Corporation. All rights reserved August 1998

Installation Guide

SCXI-1181K Custom Module Assembly

This guide documents the contents of your SCXI-1181K custom module assembly kit and

includes illustrations of the circuit board specifications and the module assembly.

Introduction

The SCXI-1181K custom module assembly kit includes the unassembled components you need

to build a custom SCXI module, but not the actual circuit board. All of the mechanical

components of an SCXI module, such as the metal enclosure, front and back panels, and

connectors, are included.

The SCXI-1181K is intended for developers of custom SCXI modules who design and lay out

custom circuit boards for modules. For prototyping or building low-volume custom SCXI

modules, the fully assembled SCXI-1181 breadboard moduleis more appropriate.

What Your Kit Should Contain

The SCXI-1181K custom module assembly kit (part number 776572-81K) contains the

components listed in the following table. The reference numbers in the left column of the table

refer to callouts in Figure 1.

Reference

Number Component Quantity

1 Module front panel 1

2

3 Thumb screw, 2.5 mm 2

4 #4 x 5/16 in. Phillips screw, flat head 2

5 Enclosure base 1

6 Module rear panel 1

7 #4 x 5/16 in. Phillips screw, pan head 3

8 Enclosure cover 1

9 Identification label 1

J1 3 x 32 position Deutsche Industrie Norme

connector header 1

J2 50 position connector header 1

P1 4 x 6, 2 mm connector, push-fit 4

— Installation guide 1

1

Module front panel overlay

SCXI-1181K Custom Module Assembly Install. Guide 2 © National Instruments Corporation

Refer to the reference numbers of the components in the previous table and the corresponding

components in Figure 1 for module assembly.

Note: The four P1 connectors have a push-fit peg. Secure the P1 connectors to the printed

wire circuit board (PWB) by pushing the connector onto the PWB so that the middle

peg of the connector presses into the 0.081 in. hole in the PWB. National Instruments

recommends using the push-fit peg hand tool (part number CTHT-200) manufactured

by ITT Cannon for this installation. You can contact ITT Cannon at (800) 845-7000.

Figure 2 shows the SCXI module PWB outline.

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere National Instruments Steuereinheit Handbücher

National Instruments

National Instruments ELVIS RIO CM Bedienungsanleitung

National Instruments

National Instruments CFP-TC-120 Bedienungsanleitung

National Instruments

National Instruments SCC-LP Series Bedienungsanleitung

National Instruments

National Instruments 2591 Bedienungsanleitung

National Instruments

National Instruments PXI Terminal Block NI TB-2708 Bedienungsanleitung

National Instruments

National Instruments 9853 Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-1001 Bedienungsanleitung

National Instruments

National Instruments NI 9930 Bedienungsanleitung

National Instruments

National Instruments CompactRIO cRIO-FRC Bedienungsanleitung

National Instruments

National Instruments NI 9759 Bedienungsanleitung

National Instruments

National Instruments NI PXI-6682 Bedienungsanleitung

National Instruments

National Instruments Isolated Analog Output Module SCC-AO10 Bedienungsanleitung

National Instruments

National Instruments SCC-TC Series Bedienungsanleitung

National Instruments

National Instruments NI R Series Bedienungsanleitung

National Instruments

National Instruments PXIe-6674T Bedienungsanleitung

National Instruments

National Instruments PXIe-8238 Bedienungsanleitung

National Instruments

National Instruments SET-1415 Stücklistenhandbuch

National Instruments

National Instruments SCXI-1141 Bedienungsanleitung

National Instruments

National Instruments 6587 Bedienungsanleitung

National Instruments

National Instruments PXIe-5693 Handbuch

National Instruments

National Instruments NI 9401 Bedienungsanleitung

National Instruments

National Instruments NI-9208 Bedienungsanleitung

National Instruments

National Instruments Isolated Current Output Module SCC-CO20 Bedienungsanleitung

National Instruments

National Instruments ISM-7400 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung