National Instruments CompactRIO cRIO-9002 Bedienungsanleitung

National Instruments cRIO-9004 Manual

Get Pricing & Availability at

ApexWaves.com

Call Today: 1-800-915-6216

Email: sales@apexwaves.com

https://www.apexwaves.com/modular-systems/national-instruments/compactrio-controllers/cRIO-9004

USER MANUAL AND SPECIFICATIONS

NI cRIO-9002/9004

Intelligent Real-Time Embedded Controller for CompactRIO

Figure 1. CompactRIO cRIO-9002/9004

INPUT

9–35 V

17 W MAX

---

1. LEDs

2. Power Connector

3. DIP Switches

4. Reset Button

5. RJ-45 Ethernet Port

6. RS-232 Serial Port

This document describes how to connect the cRIO-9002/9004 to a network and how to use the

features of the cRIO-9002/9004. This document also contains specifications for the

controllers.

Safety Guidelines

Caution Do not operate the cRIO-9002/9004 in a manner not specified in this

document. Product misuse can result in a hazard. You can compromise the safety

protection built into the product if the product is damaged in any way. If the product

is damaged, return it to NI for repair.

Safety Guidelines for Hazardous Locations

The cRIO-9002/9004 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4

hazardous locations; Class I, Zone 2, AEx nA IIC T4 and Ex nA IIC T4 hazardous locations;

and nonhazardous locations only. Follow these guidelines if you are installing the

cRIO-9002/9004 in a potentially explosive environment. Not following these guidelines may

result in serious injury or death.

Caution Do not disconnect I/O-side wires or connectors unless power has been

switched off or the area is known to be nonhazardous.

Caution Do not remove modules unless power has been switched off or the area is

known to be nonhazardous.

Caution Substitution of components may impair suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications, install the system in an enclosure

rated to at least IP54 as defined by IEC/EN 60079-15.

Special Conditions for Hazardous Locations Use in Europe and

Internationally

The cRIO-9002/9004 has been evaluated as Ex nA IIC T4 Gc equipment under DEMKO

Certificate No. 03 ATEX 0324020X and is IECEx UL 14.0089X certified. Each device is

marked II 3G and is suitable for use in Zone 2 hazardous locations, in ambient temperatures

of -40 °C ≤ Ta ≤ 70 °C.

Caution You must make sure that transient disturbances do not exceed 140% of

the rated voltage.

Caution The system shall only be used in an area of not more than Pollution

Degree 2, as defined in IEC 60664-1.

Caution The system shall be mounted in an ATEX/IECEx-certified enclosure with

a minimum ingress protection rating of at least IP54 as defined in IEC/EN 60079-15.

Caution The enclosure must have a door or cover accessible only by the use of a

tool.

2| ni.com | NI cRIO-9002/9004 User Manual and Specifications

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for marine (shipboard) applications.

To verify Lloyd’s Register certification for a product, visit ni.com/certification and search for

the LR certificate, or look for the Lloyd’s Register mark on the product.

Caution In order to meet the EMC requirements for marine applications, install the

product in a shielded enclosure with shielded and/or filtered power and input/output

ports. In addition, take precautions when designing, selecting, and installing

measurement probes and cables to ensure that the desired EMC performance is

attained.

Installing the Controller on the Chassis

The following figure shows the dimensions of the cRIO-9002/9004.

NI cRIO-9002/9004 User Manual and Specifications | © National Instruments | 3

Figure 2. cRIO-9002/9004, Front and Bottom View with Dimensions

77.3 mm

(3.04 in.)

90.2 mm

(3.55 in.)

44.2 mm

(1.74 in.)

88.1 mm

(3.47 in.)

44.2 mm

(1.74 in.)

1. M4 Thread

Complete the following steps to install the controller on the chassis.

1. Make sure that no power is connected to the controller or the chassis.

2. Align the controller with the chassis as shown in the following figure.

4| ni.com | NI cRIO-9002/9004 User Manual and Specifications

Figure 3. Installing the cRIO-9002/9004 in the Chassis

1. Controller

2. Captive Screws

3. Controller Slot

4. Reconfigurable Embedded Chassis

3. Slide the controller onto the controller slot on the chassis. Press firmly to ensure the

chassis connector and the controller connector are mated.

4. Using a number 2 Phillips screwdriver, tighten the two captive screws on the front of the

controller to 1.3 N · m (11.5 lb · in.) of torque.

Connecting the Controller to a Network

Connect the controller to an Ethernet network using the RJ-45 Ethernet port on the controller

front panel. Use a standard Category 5 (CAT-5) or better shielded, twisted-pair Ethernet cable

to connect the chassis to an Ethernet hub, or use an Ethernet crossover cable to connect the

chassis directly to a computer.

Caution To prevent data loss and to maintain the integrity of your Ethernet

installation, do not use a cable longer than 100 m. If you are using 100 Mbps

Ethernet, National Instruments recommends using a CAT-5 or better shielded

twisted-pair Ethernet cable.

If you need to build your own cable, refer to the Cabling section for more information about

Ethernet cable wiring connections.

The host computer communicates with the controller over a standard Ethernet connection. If

the host computer is on a network, you must configure the controller on the same subnet as the

NI cRIO-9002/9004 User Manual and Specifications | © National Instruments | 5

host computer. If neither the host computer nor the CompactRIO controller is connected to a

network, you can connect the two directly using a crossover cable.

If you want to use the controller on a subnet other than the one the host computer is on, first

connect the controller on the same subnet as the host computer. Use DHCP to assign an IP

address or reassign a static IP address for the subnet where you want it to be and physically

move it to the other subnet. The first time you configure the controller, you must also install

software on it. Refer to the Measurement & Automation Explorer Help for more information

about configuring the controller in Measurement & Automation Explorer (MAX). Contact

your network administrator if you need assistance configuring the host computer and

controller on the same subnet.

Wiring Power to the Controller

Caution You must install the controller on a CompactRIO chassis and tighten the

captive screws before you apply power to the controller. Installing the controller

while power is applied to it can cause damage to the chassis.

The cRIO-9002/9004 requires an external power supply that meets the specifications in the

Power Requirements section. The cRIO-9002/9004 filters and regulates the supplied power

and provides power for all of the I/O modules in the chassis. You can connect two power

sources to the cRIO-9002/9004. The cRIO-9002/9004 draws power from the power source

with the higher voltage. The cRIO-9002/9004 has one layer of reversed-voltage protection.

The power source you connect to the cRIO-9002/9004 must provide an additional layer of

reversed-current flow protection. Complete the following steps to connect power sources to

the cRIO-9002/9004.

1. Install a ferrite across the negative and positive wires for both the V1 and V2 terminals.

6| ni.com | NI cRIO-9002/9004 User Manual and Specifications

Figure 4. Wiring Power to the cRIO-9002/9004

2. Connect the positive lead of one of the power sources to the V1 terminal and the negative

lead to one of the C terminals.

3. Connect the positive lead of the other power source to the V2 terminal and the negative

lead to one of the C terminals.

Note The controller draws power from either V1 or V2 depending on which

terminal has a higher voltage. It does not draw power from both terminals.

Caution The C terminals are internally connected to each other. Make sure to

use two power sources that have a common ground.

Powering On the cRIO-9002/9004

Plug in each power supply to the CompactRIO system. The controller runs a power-on self test

(POST). During the POST, the Power, Status, and User1 LEDs turn on. The User1 and Status

LEDs turn off, indicating that the POST is complete.

Boot Options

You can configure the controller to launch an embedded stand-alone application each time you

boot the controller. Refer to the LabVIEW Help for more information.

The following table lists the reset options available on CompactRIO backplanes, such as the

cRIO-910x devices. Use these options to determine how the CompactRIO controllers, such as

the cRIO-9002/9004 controllers, are reset in various conditions.

NI cRIO-9002/9004 User Manual and Specifications | © National Instruments | 7

Table 1. CompactRIO Reset Options

Backplane Reset Option Controller Behavior

Do Not Autoload on Reset Does not load the FPGA bit stream from flash memory

Autoload on Power-On Reset Loads the FPGA bit stream from flash memory to the

FPGA when the controller powers on.

Autoload on Any Device Reset Loads the FPGA bit stream from flash to the FPGA when

you reboot the controller either with or without cycling

power.

Connecting Serial Devices to the

cRIO-9002/9004

The cRIO-9002/9004 has an RS-232 serial port to which you can connect devices such as

displays or input devices. Use the Serial VIs to read from and write to the serial port from a

LabVIEW Real-Time application. For more information about the Serial VIs, refer to the

LabVIEW Help.

Figure 5. Controller Serial Port

Pin 1

Pin 5

Pin 6

Pin 9

Table 2. DB-9 Pin Descriptions

Pin Signal

1 DCD

2 RXD

3 TXD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI

8| ni.com | NI cRIO-9002/9004 User Manual and Specifications

Configuring DIP Switches

Figure 6. DIP Switches

SAFE MODE

CONSOLE OUT

IP RESET

NO APP

USER1

ON OFF

All of the DIP switches are in the OFF position when the chassis is shipped from National

Instruments.

SAFE MODE Switch

The position of the SAFE MODE switch determines whether the embedded LabVIEW Real-

Time engine launches at startup. If the switch is in the OFF position, the LabVIEW Real-Time

engine launches. Keep this switch in the OFF position during normal operation. If the switch is

in the ON position at startup, the cRIO-9002/9004 launches only the essential services

required for updating its configuration and installing software. The LabVIEW Real-Time

engine does not launch.

If the software on the controller is corrupted, you must put the controller into safe mode and

reformat the controller drive. You can put the controller into safe mode by powering it up

either with the SAFE MODE switch in the ON position or with no software installed on the

drive. Refer to the Measurement & Automation Explorer Help for more information about

installing software on a controller and reformatting the drive on the controller.

CONSOLE OUT Switch

With a serial-port terminal program, you can use the CONSOLE OUT switch to read the IP

address and firmware version of the controller. Use a null-modem cable to connect the serial

port on the chassis to a computer. Push the switch to the ON position. Make sure that the

serial-port terminal program is configured to the following settings:

• 9,600 bits per second

• Eight data bits

• No parity

• One stop bit

The serial-port terminal program displays the IP address and firmware version. Keep this

switch in the OFF position during normal operation.

IP RESET Switch

Push the IP RESET switch to the ON position and reboot the controller to reset the IP address

and other TCP/IP settings of the controller to the factory defaults. Refer to the Troubleshooting

Network Communication section for more information about resetting the IP address. You also

NI cRIO-9002/9004 User Manual and Specifications | © National Instruments | 9

Andere Handbücher für CompactRIO cRIO-9002

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Instruments Controller Handbücher

National Instruments

National Instruments CompactRIO sbRIO-9603 Montageanleitung

National Instruments

National Instruments PXIe-8840 Quad-Core Bedienungsanleitung

National Instruments

National Instruments Compact FieldPoint cFP-21 Series Bedienungsanleitung

National Instruments

National Instruments cRIO-9032 Bedienungsanleitung

National Instruments

National Instruments PXIe-8100 Bedienungsanleitung

National Instruments

National Instruments GPIB Series Bedienungsanleitung

National Instruments

National Instruments PXI-8820 Bedienungsanleitung

National Instruments

National Instruments NI cRIO-9035 Bedienungsanleitung

National Instruments

National Instruments 9862 Bedienungsanleitung

National Instruments

National Instruments NI RMC-8355 Bedienungsanleitung

National Instruments

National Instruments PXI NI PXI-8105 Bedienungsanleitung

National Instruments

National Instruments NI cRIO-9065 Bedienungsanleitung

National Instruments

National Instruments Two-Slot Embedded Controller NI PXI-8183 Bedienungsanleitung

National Instruments

National Instruments GPIB-SCSI-A Bedienungsanleitung

National Instruments

National Instruments sbRIO-9637 Bedienungsanleitung

National Instruments

National Instruments GPIB GPIB-ENET/100 Bedienungsanleitung

National Instruments

National Instruments MXI-Express Gen-3 x16 Bedienungsanleitung

National Instruments

National Instruments PXIe-8881 Bedienungsanleitung

National Instruments

National Instruments 7330 Bedienungsanleitung

National Instruments

National Instruments cRIO-9023 Bedienungsanleitung

National Instruments

National Instruments Motion Control 7344 Bedienungsanleitung

National Instruments

National Instruments 73 Series Bedienungsanleitung

National Instruments

National Instruments VXIpc 600 Series Bedienungsanleitung

National Instruments

National Instruments NI cRIO-9024 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung