National Instruments AT-GPIB Bedienungsanleitung

Getting Started with Your AT-GPIB

and the NI-488M™Software for

SCO UNIX System V/386

October 1993 Edition

Part Number 320374-01

National Instruments Corporate Headquarters

6504 Bridge Point Parkway

Austin, TX 78730-5039

(512) 794-0100

Technical support fax: (800) 328-2203

(512) 794-5678

Branch Offices:

Australia (03) 879 9422, Austria (0662) 435986, Belgium 02/757.00.20,

Canada (Ontario) (519) 622-9310, Canada (Québec) (514) 694-8521,

Denmark 45 76 26 00, Finland (90) 527 2321, France (1) 48 14 24 24,

Germany 089/741 31 30, Italy 02/48301892, Japan (03) 3788-1921,

Mexico 95 800 010 0793, Netherlands 03480-33466, Norway 32-84 84 00,

Singapore 2265886, Spain (91) 640 0085, Sweden 08-730 49 70,

Switzerland 056/20 51 51, Taiwan 02 377 1200, U.K. 0635 523545

Limited Warranty

The AT-GPIB is warranted against defects in materials and workmanship

for a period of two years from the date of shipment, as evidenced by

receipts or other documentation. National Instruments will, at its option,

repair or replace equipment that proves to be defective during the warranty

period. This warranty includes parts and labor.

The media on which you receive National Instruments software are

warranted not to fail to execute programming instructions, due to defects in

materials and workmanship, for a period of 90 days from date of shipment,

as evidenced by receipts or other documentation. National Instruments will,

at its option, repair or replace software media that do not execute

programming instructions if National Instruments receives notice of such

defects during the warranty period. National Instruments does not warrant

that the operation of the software shall be uninterrupted or error free.

A Return Material Authorization (RMA) number must be obtained from the

factory and clearly marked on the outside of the package before any

equipment will be accepted for warranty work. National Instruments will

pay the shipping costs of returning to the owner parts which are covered by

warranty.

National Instruments believes that the information in this manual is

accurate. The document has been carefully reviewed for technical accuracy.

In the event that technical or typographical errors exist, National

Instruments reserves the right to make changes to subsequent editions of

this document without prior notice to holders of this edition. The reader

should consult National Instruments if errors are suspected. In no event

shall National Instruments be liable for any damages arising out of or

related to this document or the information contained in it.

EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO

WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. CUSTOMER'S RIGHT TO RECOVER DAMAGES

CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF NATIONAL

INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE

PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE

LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA, PROFITS,

USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES,

EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the

liability of National Instruments will apply regardless of the form of action,

whether in contract or tort, including negligence. Any action against

National Instruments must be brought within one year after the cause of

action accrues. National Instruments shall not be liable for any delay in

performance due to causes beyond its reasonable control. The warranty

provided herein does not cover damages, defects, malfunctions, or service

failures caused by owner's failure to follow the National Instruments

installation, operation, or maintenance instructions; owner's modification of

the product; owner's abuse, misuse, or negligent acts; and power failure or

surges, fire, flood, accident, actions of third parties, or other events outside

reasonable control.

Under the copyright laws, this publication may not be reproduced or

transmitted in any form, electronic or mechanical, including photocopying,

recording, storing in an information retrieval system, or translating, in

whole or in part, without the prior written consent of National Instruments

Corporation.

Trademarks

NI-488M™is a trademark of National Instruments Corporation.

Product and company names listed are trademarks or trade names of their

respective companies.

WARNING REGARDING MEDICAL AND

CLINICAL USE OF NATIONAL

INSTRUMENTS PRODUCTS

National Instruments products are not designed with components and testing

intended to ensure a level of reliability suitable for use in treatment and

diagnosis of humans. Applications of National Instruments products

involving medical or clinical treatment can create a potential for accidental

injury caused by product failure, or by errors on the part of the user or

application designer. Any use or application of National Instruments

products for or involving medical or clinical treatment must be performed by

properly trained and qualified medical personnel, and all traditional medical

safeguards, equipment, and procedures that are appropriate in the particular

situation to prevent serious injury or death should always continue to be

used when National Instruments products are being used. National

Instruments products are NOT intended to be a substitute for any form of

established process, procedure, or equipment used to monitor or safeguard

human health and safety in medical or clinical treatment.

FCC/DOC Radio Frequency

Interference Compliance

This equipment generates and uses radio frequency energy and, if not

installed and used in strict accordance with the instructions in this manual,

may cause interference to radio and television reception. This equipment

has been tested and found to comply with the following two regulatory

agencies:

Federal Communications Commission

This device complies with Part 15 of the Federal Communications

Commission (FCC) Rules for a Class B digital device. A Class B device is

distinguishable from a Class A device by the appearance of an FCC ID

number located on the Class B device.

Canadian Department of Communications

This device complies with the limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications (DOC).

Le présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de classe B

prescrites dans le règlement sur le brouillage radioélectrique édicté par le

ministère des communications du Canada.

Instructions to Users

These regulations are designed to provide reasonable protection against

interference from the equipment to radio and television reception in

residential areas.

There is no guarantee that interference will not occur in a particular

installation. However, the chances of interference are much less if the

equipment is installed and used according to this instruction manual.

If the equipment does cause interference to radio or television reception,

which can be determined by turning the equipment on and off, one or more

of the following suggestions may reduce or eliminate the problem.

• Operate the equipment and the receiver on different branches of your

AC electrical system.

• Move the equipment away from the receiver with which it is interfering.

• Reorient or relocate the receiver’s antenna.

• Be sure that the equipment is plugged into a grounded outlet and that

the grounding has not been defeated with a cheater plug.

Notice to user: Changes or modifications not expressly approved by

National Instruments could void the user’s authority to

operate the equipment under the FCC Rules.

If necessary, consult National Instruments or an experienced radio/television

technician for additional suggestions. The following booklet prepared by

the FCC may also be helpful: How to Identify and Resolve Radio-TV

Interference Problems. This booklet is available from the U.S. Government

Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4.

Bescheinigung des Herstellers/Importeurs

Hiermit wird bescheinigt, daß die AT-GPIB in Übereinstimmung mit den

Bestimmungen der Vfg. 1046/1984 funk entstört ist.

Der Detuschen Bundespost wurde das Inverkehrbringen dieses Gerätes

angezeigt und die Berechtigung zur Überprüfung der Serie auf

Bestimmungen eingeräumt.

Contents

About This Manual ..........................................................................xiii

Organization of This Manual......................................................xiii

Conventions Used in This Manual .............................................xiv

Related Documentation ..............................................................xv

Customer Communication ..........................................................xv

Chapter 1

Introduction.........................................................................................1-1

What You Need to Get Started...................................................1-1

Software Description ..................................................................1-1

Chapter 2

Hardware Configuration and Installation..............................2-1

Step 1. Configure the Hardware...............................................2-1

Switch and Jumper Settings .........................................2-2

Base I/O Address Selection..........................................2-3

Possible Conflicts...........................................2-6

Interrupt Selection ........................................................2-8

Possible Conflicts...........................................2-11

DMA Channel Selection ..............................................2-13

Shield Ground Configuration.......................................2-18

Step 2. Install the Hardware .....................................................2-19

Chapter 3

Software Installation and Configuration ................................3-1

Step 1. Prepare for Software Installation .................................3-1

Step 2. Install the NI-488M Software ......................................3-2

A. Set Up a Working Directory...................................3-2

B. Install the Utility Files ............................................3-3

C. Install the C Library ...............................................3-3

Step 3. Load the NI-488M Driver ............................................3-3

A. Change the Software Settings.................................3-4

DMA Channel................................................3-4

Base I/O Address and Interrupt Vector

Number ..........................................................3-5

B. Install the Driver.....................................................3-5

Automatic Installation ...................................3-5

Manual Installation ........................................3-6

Contents

AT-GPIB for SCO UNIX x © National Instruments Corp.

Step 4. Configure the Software ................................................3-7

Running ibconf.............................................................3-7

Exiting ibconf...............................................................3-7

System Configuration Information...............................3-8

Step 5. Verify the Installation...................................................3-8

Removing the Driver ..................................................................3-9

Developing Your Application..................................................... 3-10

Appendix A

New NI-488M Functions ................................................................A-1

IBDEV(3) ...................................................................................A-2

IBLINES(3) ................................................................................A-4

IBLN(3) ......................................................................................A-6

Appendix B

Special Instructions for Changing the

Software Settings...............................................................................B-1

Using a Base I/O Address Different from the Software

Default Setting ............................................................................B-1

Using Interrupt Vector Number 11 or DMA Channel 5.............B-2

Appendix C

Hardware Specifications................................................................C-1

Appendix D

Customer Communication............................................................D-1

Glossary.................................................................................................G-1

Contents

Figures

Figure 2-1. AT-GPIB Parts Locator Diagram ....................................2-1

Figure 2-2. Base I/O Address Switch Settings ...................................2-4

Figure 2-3. Interrupt Jumper Settings................................................. 2-10

Figure 2-4. DMA Channel Jumper Setting......................................... 2-15

Figure 2-5. DMA Jumper Setting for No DMA Channel...................2-16

Figure 2-6. Ground Configuration Jumper Settings ...........................2-18

Tables

Table 2-1. Software and Hardware Default Settings and Available

Hardware Configurations.................................................2-2

Table 2-2. Software Default AT-GPIB Base I/O Addresses.............2-3

Table 2-3. Possible Base I/O Address Switch Settings for the

AT-GPIB..........................................................................2-5

Table 2-4. PC AT I/O Address Map .................................................2-7

Table 2-5. Software Default AT-GPIB Interrupt Request Line ........2-9

Table 2-6. PC AT Interrupt Assignment Map...................................2-11

Table 2-7. Software Default AT-GPIB DMA Channel.....................2-13

Table 2-8. DMA Channels for the AT-GPIB ....................................2-14

Table 2-9. PC AT 16-Bit DMA Channel Assignment Map ..............2-17

Table 3-1. Software Default Settings ................................................3-4

Table C-1. Electrical Characteristics .................................................C-1

Table C-2. Environmental Characteristics.........................................C-1

Table C-3. Physical Characteristics ...................................................C-1

Andere Handbücher für AT-GPIB

Inhaltsverzeichnis

Andere National Instruments Aufnahmegeräte Handbücher

National Instruments

National Instruments GPIB-PCII Bedienungsanleitung

National Instruments

National Instruments VXI-USB Bedienungsanleitung

National Instruments

National Instruments Multisystem eXtension Interface NI PCIe-836x Bedienungsanleitung

National Instruments

National Instruments FieldPoint FP-1000 Bedienungsanleitung

National Instruments

National Instruments GPIB-MAC Bedienungsanleitung

National Instruments

National Instruments UMI-7774 Bedienungsanleitung

National Instruments

National Instruments MXI PCIe-8371 Bedienungsanleitung

National Instruments

National Instruments 8234 Bedienungsanleitung

National Instruments

National Instruments PCMCIA-232 Bedienungsanleitung

National Instruments

National Instruments NI 951x Bedienungsanleitung

National Instruments

National Instruments GPIB-SCSI-A Bedienungsanleitung

National Instruments

National Instruments DAQ Series Bedienungsanleitung

National Instruments

National Instruments NI PCIe-8233 Bedienungsanleitung

National Instruments

National Instruments VXI-AT2023 Bedienungsanleitung

National Instruments

National Instruments VXI-SB2020 Bedienungsanleitung

National Instruments

National Instruments ENET-232 Series Bedienungsanleitung

National Instruments

National Instruments GPIB-COM Bedienungsanleitung

National Instruments

National Instruments PXIe-8240 Bedienungsanleitung

National Instruments

National Instruments SC-2043-SG Bedienungsanleitung

National Instruments

National Instruments NI PCIe-8255R Bedienungsanleitung

National Instruments

National Instruments VXI-AT2022 Bedienungsanleitung

National Instruments

National Instruments UMI-7664 Bedienungsanleitung

National Instruments

National Instruments NI VISION PCI-8254R Bedienungsanleitung

National Instruments

National Instruments PXI-PCI 8330 Series Bedienungsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch