National Instruments 8260 Bedienungsanleitung
USER GUIDE
SATA Hard Drive Removal and
Replacement Procedure for
NI 8260 4-Drive Storage Module
This document provides instructions for removing and replacing a SATA
hard drive with your NI 8260 4-Drive Storage Module.
Cautions Before you handle the NI 8260 or the hard drive, discharge any built-up static
charge that may have accumulated. Electrostatic discharge may damage the NI 8260 and/or
the hard drive.
Avoid mounting the hard drive near strong magnetic sources such as loud speakers. Ensure
that the hard drive is not affected by external magnetic fields.
Protect the hard drive and NI 8260 from hard contact with other objects. Impacts may
damage the equipment.
Do not press the cover of the hard drive. Pressing it too hard may cause cover and spindle
motor contact, which would damage the hard drive.
When handling the hard drive, do not touch the printed circuit board. Hold the hard drive
by its edges.
Removing a Hard Drive
Notes You will need to remove Drive 1 before you can remove Drive 0 (Drive 0 is the
bottom drive).
If it is difficult to remove the hard drive, loosen all of the screws holding the installed
hard drives.
SATA Hard Drive Procedure for NI 8260 Storage Module 2 ni.com
Complete the following steps to remove a hard drive from the
NI 8260 4-Drive Storage Module.
1. Place the module on its side and locate the screws holding the hard
drive in place, as shown in Figure 1.
Figure 1. Hard Drive Screws
2. Hold the module firmly in place as you remove the four screws from
the drive to be replaced.
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.
Refer to the Terms of Use section on ni.com/legal for more information about National
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade
names of their respective companies. For patents covering National Instruments products/technology,
refer to the appropriate location: Help»Patents in your software, the patents.txt file on your
media, or the National Instruments Patent Notice at ni.com/patents.
© 2009 National Instruments Corporation. All rights reserved. 372900A-01 May09
Installing the Hard Drive
Complete the following instructions to install a hard drive in the
NI 8260 4-Drive Storage Module.
1. Turn the module on its side and insert the hard drive straight into the
open slot by aligning the screw holes on the hard drive as shown in
Figure 3.
Figure 3. Inserting a Hard Drive
2. When the hard drive is fully inserted into the SATA connector, install
all four screws to secure the hard drive in place, as indicated in
Figure 4.
Figure 4. Securing the Hard Drive in the Module
3. Check to see if the screws on all installed hard drives are tightened.
If you experience issues during the removal or installation of a hard drive,
please contact National Instruments.
For more information on these tools, refer to ni.com/support.
Inhaltsverzeichnis
Andere National Instruments Lagerung Handbücher
National Instruments
National Instruments HDD-8261 Bedienungsanleitung
National Instruments
National Instruments PXIe-8267 Bedienungsanleitung
National Instruments
National Instruments HDD-8263 Bedienungsanleitung
National Instruments
National Instruments USB-622 Series Bedienungsanleitung
National Instruments
National Instruments PA5080L Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung