National Semiconductor DS15BA101 Bedienungsanleitung

January 2008

Rev. 0.3

150 – 1500 Mbps Cable Extender

Chipset

(DS15BA101/DS15EA101)

Evaluation Kit

USER MANUAL

Part Number: DriveCable02EVK NOPB

For the latest documents concerning these products and evaluation kit, visit lvds.national.com. Schematics

and gerber files are also available at lvds.national.com.

DriveCable02EVK User Manual

Table of Contents

Overview................................................................................................................................................ 3

Board Description................................................................................................................................... 4

Setting Up the DriveCable02EVK Evaluation Kit ................................................................................. 5

Evaluation with the 100-ohm Differential Balanced Cables .................................................................. 6

Evaluation with the 50-ohm Coaxial Cables ........................................................................................ 10

Page 2 of 12

DriveCable02EVK User Manual

Overview

The DriveCable02EVK is an evaluation kit designed for demonstrating performance of the DS15BA101

and DS15EA101, a cable extender chipset. The kit enables evaluation of the chipset with 100-ohm

differential cables such as twin-axial and low cost CAT5e/6/7 twisted pair cables and 50-ohm coaxial

cables.

The purpose of this document is to: familiarize you with the DriveCable02EVK, suggest the test setup

procedures and instrumentation, and guide you through some typical measurements that demonstrate

performance of the chipset in typical applications.

Page 3 of 12

DriveCable02EVK User Manual

Board Description

Figure 1 shows a drawing of the board. It is a 3 inch x 4 inch 6-layer PCB with a two-device layout that is

capable of demonstrating performance and all features of the DS15BA101 and DS15EA101.

VDD

Vbias

GND

Figure 1. DriveCable02EVK Board

Connector Device Function

JP1 U1 Select output amplitude

JP2 U2 Output enable

JP3 U1 Set input common mode

voltage (Optional)

Table 1. DriveCable02EVK Connector-Device-Function Cross Reference

Page 4 of 12

DriveCable02EVK User Manual

Setting Up the DriveCable02EVK

Evaluation Kit

This section provides a quick reference for setting up some typical test configurations using the

DriveCable02EVK that will enable you to evaluate the solution with 100-ohm differential cables (twin-

axial and twisted pair cables) as well as 50-ohm coaxial cables.

Page 5 of 12

DriveCable02EVK User Manual

Evaluation with 100-ohm Differential Balanced Cables

The DriveCable02EVK can be used to evaluate the chipset with 100-ohm differential cables (twin-axial

and twisted pair cables). Examples are CAT5e/6/7 cable assemblies such as Belden 1500A, Belden 1700A,

Siemon CAT7 Tera, Belden 89207 and Amphenol SKEWCLEAR series of cables. Figure 2 is a simplified

block diagram of the configuration.

Advantest D3186

Pattern Generator

Connector

Adapter

Connector

Adapter

Cable

Tektronix

TDS 6154C

Oscilloscope

Cable Extender Chipset Evaluation Board

P/N: DriveCable02EVK, Rev. 2.0

Gigabits@ManyMeters

Figure 2. Test Setup for 100-ohm Differential Cable Evaluation

Note: Connector Adapters are NOT included in this kit. Currently, RJ45-SMA adapters are

available and can be ordered separately. The part number is DS91C176EVK NOPB. If cable

assemblies have other than RJ-45 connectors, it is recommended to obtain/develop an adapter board

similar to the RJ45-SMA adapter to ensure good impedance control of the signal path. For more

information about the RJ45-SMA Adapter check:

http://www.national.com/appinfo/lvds/ds91c176evk.html

Page 6 of 12

DriveCable02EVK User Manual

Follow these steps to set up the DriveCable02EVK for evaluation with 100-ohm differential balanced

cables:

1. Configure DriveCable02EVK board:

a) Provide 3.3 V between the J2 (VDD) and J1 (GND). This powers all devices on the board.

b) Set DS15BA101 (U1) output voltage amplitude to 0.4 V by using JP1.

c) Enable DS15EA101 (U2) outputs by setting its EN* pin to low. This is accomplished by

placing a jumper across the GND and SIG pins of the connector JP2.

2. Connect the DS15BA101 inputs to a signal source (e.g. Pattern Generator or Serializer output).

a) Note the AC-coupling capacitors on the inputs (SMA1 and SMA2)

b) Adjust the signal parameters (VOH, VOL, VCM) so that they comply with the DS15BA101

input requirements.

c) If DC-coupled interface is desired, use 0-ohm SM0402 resistors in place of the C1 and C2.

d) There is a provision to add an optional resistor divider network (R12 and R13) on the

DS15BA101 inputs in case one desires biasing the input signal externally (note: there is

already an internal biasing network on the DS15BA101 inputs). In addition, the JP3

connector provides signal biasing provision for a voltage source.

3. Attach the connector adapters (if available) to the DS15BA101 outputs (SMA3 and SMA4) and

DS15EA101 inputs (SMA5 and SMA6).

4. Connect a 100-ohm cable assembly with corresponding plugs on its ends.

5. The LED1 will illuminate if the DS15EA101 (U2) detects a valid signal.

6. Connect the DS15EA101 (U2) outputs directly to an oscilloscope, a bit error rate tester (BERT)

receiver or a deserializer using good quality coaxial cables. Note that the equalizer outputs have

internal 50-ohm pull-ups and that there are on-board AC-coupling capacitors.

7. Observe the results on the oscilloscope or BERT receiver.

Page 7 of 12

DriveCable02EVK User Manual

Figure 3 presents typical maximum data rate as a function of CAT5e cable length. The data was

collected on four chipsets (A, B, C and D). The data in red was taken with the 0.5 UI jitter criteria

while the data in blue was taken with the 0.25 UI jitter criteria.

0.00

0.25

0.50

0.75

1.00

1.25

1.50

1.75

2.00

2.25

2.50

0 25 50 75 100 125

Cable Length [m]

Maximum Data Rate [Gbps]

A B C D A B C D

Figure 3. DS15BA101 and DS15EA101 Performance with CAT5e Cable

Page 8 of 12

DriveCable02EVK User Manual

Figure 4 presents maximum data rate as a function of CAT7 cable length. The data was collected on four

chipsets (A, B, C and D). The data in red was taken with the 0.5 UI jitter criteria while the data in blue was

taken with the 0.25 UI jitter criteria.

0.00

0.25

0.50

0.75

1.00

1.25

1.50

1.75

2.00

2.25

2.50

2.75

3.00

0 25 50 75 100

Cable Length [m]

Maximum Data Rate [Gbps]

A B C D A B C D

Figure 4. DS15BA101 and DS15EA101 Performance with CAT7 Cable

Page 9 of 12

DriveCable02EVK User Manual

Evaluating 50-ohm Coaxial Cables

The DriveCable02EVK can be used to evaluate 50-ohm coaxial cables. Examples of 50-ohm coaxial

cables are Belden 9914 and Andrew FSJ-50B. Figure 5 is a simplified block diagram of the configuration.

Advantest D3186

Pattern Generator

Cable

Tektronix

TDS 6154C

Oscilloscope

Cable Extender Chipset Evaluation Board

P/N: DriveCable02EVK, Rev. 2.0

Gigabits@ManyMeters

Figure 5. Test Setup for 50-ohm Coaxial Cable Evaluation

Page 10 of 12

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere National Semiconductor Hauptplatine Handbücher

National Semiconductor

National Semiconductor ADC122S655 Bedienungsanleitung

National Semiconductor

National Semiconductor LM5072 Bedienungsanleitung

National Semiconductor

National Semiconductor TAS2557 Bedienungsanleitung

National Semiconductor

National Semiconductor LM48555 Bedienungsanleitung

National Semiconductor

National Semiconductor ADC14DC105 Bedienungsanleitung

National Semiconductor

National Semiconductor TPS65132S Bedienungsanleitung

National Semiconductor

National Semiconductor LM49250 Bedienungsanleitung

National Semiconductor

National Semiconductor LMX2531LQ2820E Bedienungsanleitung

National Semiconductor

National Semiconductor LMX2531LQ3010E Bedienungsanleitung

National Semiconductor

National Semiconductor LM5072 Bedienungsanleitung

National Semiconductor

National Semiconductor CLINK3V28BT-85 Bedienungsanleitung

National Semiconductor

National Semiconductor SD303EVK Bedienungsanleitung

National Semiconductor

National Semiconductor POEPHYTEREV-E Bedienungsanleitung

National Semiconductor

National Semiconductor LMX2324 Bedienungsanleitung

National Semiconductor

National Semiconductor LMX2531LQ1910E Bedienungsanleitung

National Semiconductor

National Semiconductor ADC08200 Bedienungsanleitung

National Semiconductor

National Semiconductor ADC081500DEV Bedienungsanleitung

National Semiconductor

National Semiconductor TPS65132L Bedienungsanleitung

National Semiconductor

National Semiconductor LMK03002C Bedienungsanleitung

National Semiconductor

National Semiconductor LP3972 Bedienungsanleitung

National Semiconductor

National Semiconductor ADS54J69EVM Bedienungsanleitung

National Semiconductor

National Semiconductor LMX2531LQ1226E Bedienungsanleitung

National Semiconductor

National Semiconductor ADC14071 Bedienungsanleitung

National Semiconductor

National Semiconductor TSW3070EVM Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung