NAUMANN NM300 TRADITION Bedienungsanleitung

MEAT GRINDER

MASINA DE TOCAT CARNE

МЕСОМЕЛАЧКА

NAUMANN NM300 TRADITION

INSTRUCTION MANUAL

INSTRUCTIUNI DE UTILIZARE

РЪКОВОДСТВО ЗА УПОТРЕБА

Please read carefully and keep the instruction well

Cititi cu atentie instructiunile si pastrati-le pentru consultare ulterioara

Моля прочетете внимателно и запазете инструкцията

ENGLISH

DESCRIPTION

1、Body

9、Cutting blade

2、ON/0/R (ON/OFF/ Reverse)

10、Cutting plate (fine)

3、Fasten button

11、Cutting plate (medium)

4、Tube inlet

12、Cutting plate (coarse)

5、Food pusher

13、Fixing ring

6、Hopper plate

14、Sausage

7、Head Tube

15、Kebbe

8、Snake

This appliance is equipped with a thermostat system. This system will

automatically cut off the power supply to the appliance in case of

overheating.

If you appliance suddenly stops running:

1. Pull the mains plug out of the socket.

2. Press the switch button to turn off the appliance.

3. Let the appliance cool down for 60 minutes.

4. Put the mains plug in the socket.

5. Switch the appliance on again.

Please contact your dealer of an authorized service center if the thermostat

system is activated too often.

If you plug in, the indictor light will be on.

CAUTION: In order toavoida hazardous situation, this appliance must

never be connected to a time switch.

1. Read these instructions for use carefully and look at the illustrations

before using the appliance.

2. Keep these instructions for future reference.

3. Check if the voltage indicated on the appliance corresponds to the local

mains voltage before you connect the appliance.

4. Never use any accessories of parts from other manufacture .Your

guarantee will become invalid if such accessories or parts have been

used.

5. Do not use the appliance if the mains cord, the plug or other parts are

damaged.

6. If the mains cord of this appliance is damaged, it must always be

replaced by manufacture or a service center authorized, in order to

avoid hazardous situations.

7. Thoroughly clean the parts that will come into contact with food before

you use the appliance for the first time.

8. Unplug the appliance immediately after use.

INTRODUCTION

IMPORTANT

9. Never use you finger or an objection to push ingredients down the feed

tube while the appliance is running. Only the pusher is to be used for

this purpose.

10. Keep the appliance out of the reach of children.

11. Never let the appliance run unattended.

12. Switch the appliance off before detaching and install any accessory.

13. Wait until moving parts have stopped running before you remove the

parts of the appliance.

14. Never immerse the motor unit in the water or any other liquid, nor rinse

it under the tap. Use only a moist cloth to clean the motor unit.

15. Do not attempt to grind bones, nuts or other hard items.

16. Never reach into the cutter housing.Always use the pusher.

17. Never operation the appliance continuously for more than 3 minutes at

600W.

18. Accessories shall include instructions for their safe use.

19. It shall warn of potential injury from misuse.

20. This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been give supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

21. Children should be supervised to ensure that they do not play with the

appliance.

22. If the appliance is locked, please press Reversal button (REV). The

meat locked in cutter housing is untrodden, so the appliance can renew

its usual condition.

Assembling

1. Press the fasten button，hold the head and insert it into the inlet when

inserting please pay attention the head must be slanted as per arrow

indicated on the top, see (fig.1), then move the head anticlockwise so

that the head being fastened tightly. (fig.2)

2. Place the snake into the head, long end first, and turn to feed the

screw slightly until it is set into

the motor housing (fig.3).

3. Place the cutting blade onto

the snake shaft with the blade

facing the front as illustrated

(fig.4).If it is not fitted properly,

meat will not be grinded.

4. Place the desired cutting

plate next to the cutting blade,

fitting protrusions in the slot

(fig.5).

5. Support or press the center

of the cutting plate with one

finger then screw the fixing

ring tight with another hand

(fig.6). Do not over tighten.

6. Place the hopper plate on the

head and fix it into position.

7. Locate the unit on a firm

place.

8. The air passage at the bottom and the side of the motor housing

should be kept free and not blocked.

INSTRUCTION FOR USE

Mincer

1. Insert the worm shaft into the cutter housing, the plastic end first.

Place the cutter unit onto the worm shaft. (The cutting edges should

be at the front) Place the medium grinding disc or coarse grinding

disc (depending on the consistency you prefer) onto the worm shaft.

(Make sure the notch of the grinding disc fit onto the projections of

the mincer head.) Turn the screw ring in the direction of the arrow on

the cutter housing until it is properly fastened.

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter housing.

4. Now the appliance is ready for mincing.

Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of

gristle and sinews as much as possible. (Never use frozen meat!)

Put the meat in the tray. Use the pusher to gently push the meat into the

cutter hosing. (For steak tartar, mince the meat with the medium grinding

disc twice.)

Making kebab

1. Insert the worm shaft into the cutter housing,

the plastic end first.(fig.8)

Place the cone in the cutter housing.

Place the former on the cutter housing and screw

the ring on the cutter housing.(fig.9)

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter

housing.

4. Now the appliance is ready for making

kebbe.(fig.10)

Feed the prepared kebbe mixture through the

kebbe maker. Cut the continuous hollow cylinder

into the desired lengths and user as required.

Kebbe is a traditional Middle Eastern dish made

primarily of lamp and bulgur wheat which are

minced together to form a paste the mixture is extruded through the kebbe

maker and cut into short lengths . The tubes can then be stuffed with a

minced meat mixture, the ends pinched together and then deep fried.

Making sausages

1. Mince the meat

Insert the worm shaft into the cutter housing, the plastic end

first.(fig.11)

Place the separator in the cutter housing.

Place the sausage horn on the cutter housing and screw the ring on

the cutter housing.

(Make sure the notches of the separator fit onto the projections of the

mincer head.)

2. Attach the cutter housing to the motor unit.

3. Place the tray on the upright part of the cutter housing.

4. Now the appliance is ready for making sausages.

Put the ingredients in the tray. Use the pusher to gently push the meat into

the cutter housing.

Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet

skin onto the sausage horn. Push the (seasoned) minced meat into the

cutter housing. If the skin gets stuck onto the sausage horn, wet it with

some water.

HOW TO CLEAN YOUR APPLIANCE

Meat left behind in the cutter housing may be removed from the inside of

the appliance by passing a slice of bread through the cutter housing.

1. Before you clean the appliance, switch the appliance off and remove

the plug from the socket.(fig.12)

2. Press the release button and turn the whole cutter housing in the

direction of the arrow. Remove the pusher and the tray.(fig.13)

3. Unscrew the screw ring and remove all parts of the cutter housing. Do

not clean the parts in the dishwasher!

4. Wash all parts that have come into contact with meat in hot soapy

water. Clean them immediately after use.

5. Rinse them with clear hot water and dry them immediately.

6. We advise you to lubricate the cutter unit and the grinding discs with

some vegetable oil.

Disposal of old Electrical & Electronic Equipment (Applicable in the European

Union and other European countries with separate collection systems).

This symbol on the product or on its packaging indicates that this

product shall not be treated as household waste. Instead it shall be

handed over to the applicable collection point for the recycling of

electrical and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be

caused by inappropriate waste handling ofthis product. The recycling of materials will

help to conserve natural resources. For more detailed information about recycling of

this product, please contact your local city office, your household waste disposal service

or the shop where you purchased the product.

ROMANIAN

DESCRIEREA PRODUSULUI

1. Corp motor

9. Cutit de taiere

2. Buton ON/0/R

(Pornit/Oprit/Inapoi)

10. Sita de taiere (fin)

3. Buton insertie

11. Sita de taiere (mediu)

4. Sistem de prindere

12. Sita de taiere (grosier)

5. Element de impingere

13. Inel de fixare

6. Tava suport

14. Accesoriu carnati

7. Tub de introducere

15. Accesoriu chiftele si kebab

8. Melc

Aparatul este echipat cu un sistem de siguranta care opreste aparatul in

caz de supraincalzire.

Daca aparatul se opreste brusc:

1. Scoateti steckerul din priza.

2. Apasati butonul ON/OFF ca sa stingeti aparatul.

3. Lasati aparatul sa se raceasca timp de 60 minute.

4. Reintroduceti steckerul in priza.

5. Porniti aparatul.

Este bine sa contactati un service autorizat daca sistemul de siguranta se

activeaza prea des.

ATENTIE: Acest produs nu a fost creat sa functioneze impreuna cu un

temporizator extern sau sistem cu telecomanda.

Cititi pe indelete acest manual de instructiuni inainte de a folosi produsul, si

pastrati-l pentru referinte ulterioare.

1. Acest produs este destinat numai pentru uz casnic, si in spatii inchise.

2. Acest produs nu a fost conceput pentru a fi folosit cu un termostat extern

sau sistem cu telecomanda.

3. Acest produs nu a fost creat pentru a fi folosit de persoane (inclusiv copii)

cu capacitati fizice si senzoriale reduse, lipsa de experienta sau informatii,

numai in cazul in care sunt supravegheati si instruiti in legatura cu folosirea

produsului de catre o persoana responsabila pentru siguranta lor.

4. Copii trebuiesc supravegheati pentru a fi siguri ca nu se joaca cu

aparatul.

5. Pozitionati aparatul pe o suprafata plata si stabila.

6. Verificati compatibilitatea aparatului, notate pe partea inferioara, cu

reteaua de electrificare inainte de a porni aparatul.

7. Deconectati de la reteaua de electrificare cand nu folositi produsul sau

inainte de a-l curata.

8. Pentru deconectarea steckerului, nu trageti de fir, ci tinand cu o mana de

priza, trageti de stecker.

INTRODUCERE

INSTRUCTIUNI DE SIGURANTA

Inhaltsverzeichnis

Sprachen:

Andere NAUMANN Fleischwolf Handbücher

NAUMANN

NAUMANN NM12 Bedienungsanleitung

Beliebte Fleischwolf Handbücher anderer Marken

Klarstein

Klarstein Mett Max Bedienungsanleitung

Grizzly

Grizzly H7778 Bedienungsanleitung

Hobart

Hobart 4822 Bedienungsanleitung

Tasin

Tasin TS-108 Bedienungsanleitung

Adler Europe

Adler Europe AD 48 Bedienungsanleitung

camry

camry CR 4802 Bedienungsanleitung

Bake Max

Bake Max BMMG001 Bedienungsanleitung

Lumme

Lumme LU-MG2113A Bedienungsanleitung

Weston

Weston 35-3201 Bedienungsanleitung

Lumme

Lumme LU-2101 Bedienungsanleitung

GoWISE USA

GoWISE USA GW88012 Bedienungsanleitung

MPM

MPM MMM-07M Bedienungsanleitung

Weston

Weston 82-0101-W Bedienungsanleitung

BIRO

BIRO 3334SS Service-Handbuch

HOFFEN

HOFFEN MG-0440 Bedienungsanleitung

Scarlett

Scarlett SC-MG45M18 Bedienungsanleitung

Adcraft

Adcraft MG-1 Bedienungsanleitung

Johnson

Johnson tomit Bedienungsanleitung