NAUTICA Q-CLASS NAE22700 Bedienungsanleitung

EN USER MANUAL

NAE22700

ELECTRICALLY OPERATED PRODUCT

Not for children under 16 years of age. As with all electrical products, precautions should be observed

during handling to reduce the risk of electric shock.

CAUTION

User manual is also available in PDF format, contact your local distributor

to a copy if needed.

INTRODUCTION 1

WARNING 2

PARTS DIAGRAM 4

BATTERY INSTRUCTION 6

GETTING STARTED 7

BUILT-IN CARRY HANDLE 8

CARE & MAINTENANCE 9

CAMERA ASSEMBLY 10

TECHNICAL SPECIFICATIONS 11

CONTENTS

Discarded electrical appliances are recyclable and

should not be discarded in the domestic waste!

Please actively support us in conserving resources

and protecting the environment by returning this

appliance to the collection centers (if available).

FCC Statement

(For USA Regulation Only)

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired

operation.

Warning: Changes or modifications to this unit not

expressly approved by the party responsible for

compliance could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy,if

not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

INTRODUCTION

The single thruster NAUTICA Q-CLASS is a full-featured Seascooter that

gets you cruising underwater with a top speed of up to 5.3mph (8.5km/h).

Easily shift between 3 rotational speeds as you conserve your energy for more bottom time.

Use appropriate equipment such as wetsuit, approved life jacket,

mask & snorkel etc. when using Seascooter.

Only operate the Seascooter in water.

• Extremely compact and hydrodynamic design

• Foldable control handles for compact storage and travel size

• Heavy-duty retractable rubber carry handle for easy transport

• Quick set up design for instant use

• Single motor design for better maneuverability

• Runs up to 65 minutes (Normal Use)

• Weighs only 8.6 lb / 3.9 kg including battery

• Rated to 100ft / 30m

• Speed up to 5.3 MPH / 8.5 KM/H

• 3 Level rotational speed control

• Battery Level indicator

• Powered by high performance replaceable water proof Lithium Ion Battery pack

• 144 watt hour battery pack suitable for hand carry in your flight.

• Battery charging time: 3 Hours

• Product size: 221*295mm

The Seascooter is designed for use in seawater. It will have less buoyancy in fresh water, lake or pool and may sink in such waters.

Any person (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge and children playing

with the appliance are not applicable.

The connector must be removed before the appliance is cleaned and that the appliance inlet must be dried before the appliance is used again.

•Use appropriate equipment such as wetsuit, BCD, fins, mask & snorkel, surface signaling devise, regulator(s) approved life jacket etc. when using Seascooter.

•The Seascooter shall not be used in reverse direction.

• Only operate the Seascooter in water.

• Adequate lighting shall be used when using the Seascooter in dark waters and during night diving.

• When passing on this device, include the user manual and all relevant warning information and parts.

• It is the responsibility of the owner to give proper instruction and precaution (regarding the risk associated with this device) when lending the device to other people.

• Detachable power supply part shall be provided with the part of class III construction of the appliance.

• Use the AC/DC Adapter specified by the manufacturer.

WARNING

• This is not a life saving device.

DO NOT use it as a buoyancy aid.

• Read the User Manual carefully before using the product.

• Always ensure sufficient charge remains in the battery to return

to the shore surface before using the Seascooter. • Never place body parts, clothing or other objects in the

vicinity of the propeller. Do not wear loose or flowing

clothing or equipment that could be drawn into the propeller.

• Particular care should be exercised when using the Seascooter

near anybody with long hair. Users with long hair should tie it up

or wear a swimming cap when using the Seascooter.

• Do not use alcohol or mind-altering drugs prior to and during

use of this product.

• ALWAYS wear a life vest (personal floatation device - PFD) approved

by your local authorities for Snorkeling (U.S. Coast Guard Type III vest

in the US or Canadian Coast Guard approved life vest in Canada or

SAI Approval PFD in Australia or CE Approved PFD in Europe).

• Do not attach your body, clothing, other equipment to the

seascooter in any way.

• A child under 16 years old should never operate this product.

• The Seascooter is designed for 1 person use.

• ALWAYS inspect the swimming area to ensure it is free of

hazards or obstacles such as boats or swimmers before using

the Seascooter.

• Be careful when you are transporting the Seascooter and setting

it down to avoid crushing hazard on hands, foot or toes.

• Crushing / Cutting Hazard

• Be aware of appropriate water levels, tidal changes, dangerous

currents, weather change and strong offshore winds. ALWAYS

scout unfamiliar water before venturing out.

• NEVER remove the grilles except for maintenance.

• Familiarize yourself with the Seascooter functions and battery life before embarking on any dives or excursions.

• Always charge battery to its fullest before using the Seascooter.

• Do not allow sun tan oils or lotions to be in prolonged contact with the Seascooter plastic as it may cause the plastic to become

brittle and break apart.

• ALWAYS keep the Seascooter out of direct sunlight when not in use. HEAT KILLS BATTERIES AND IT MAY EXPLODE OR LEAK.

• Never remove the Battery from the Seascooter in the water.

• When not in use, always have the handles folded down.

• Do not use the Seascooter below the recommended maximum depth of 100ft / 30m.

• This machine is not intended for mixing or working with sand, concrete and material with similar physical characteristics. This

machine is only intended for swimming and diving in the water.

• Do not use the unit if it is damaged in any way.

• Replace the battery immediately if it is damaged.

• The Seascooter should only be used for scuba diving by qualified divers.

• When using the Seascooter for scuba diving, ascents and descents should be made in accordance with recognized diving practices.

• Due to safety considerations those who have not obtained a C-Card (attesting to completion of training) from an entity providing

diving instruction must not under any circumstances use this product for diving.

• In different waters (seawater, lake, pool) and conditions such as currents, temperature and pressure can affect the buoyancy of the

unit which may cause the unit to sink if accidentally released.

• DO NOT release or leave the Seascooter in the water. Always take the unit out of water when not in use.

The instructions concerning persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and

knowledge and children playing with the appliance are not applicable.

The connector must be removed before the appliance is cleaned and that the appliance inlet must be dried before the appliance is used again.

CRUSHING HAZARD:

The following action during assembly, disassembly, and transportation of the Seascooter may incur crushing hazards to your fingers or toes:

• Opening and closing the foldable control handles.

• Installing the battery.

• Setting down the Seascooter or battery.

• Accidental dropping of the Seascooter or battery.

CAUTION

PARTS DIAGRAM

1. Front Grille

2. Camera Mount (Camera not included)

3. Speed Control

4. Start Buttons

5. Control Handles (Foldable)

6. Battery Indicator

7. Foldable Control Handles Release Buttons

8. Carry Handle

9. Battery

10. Battery Charging Base

11. Charger

BATTERY CAUTION

• Use the specified charger only.

• Must be disposed of properly.

• Always store the battery in well ventilated areas where it is out of the reach of children and away

from heat and ignition sources.

• Do not incinerate, disassemble, damage, short-circuit or expose to heat.

• The battery contains safety and protection devices which, if damaged, may cause the battery to

generate heat, rupture or ignite.

• Do not place the battery in fire, direct sunlight or apply heat to the battery; it may explode or leak.

• Do not leave the battery in direct sunlight or use or store the battery inside high temperature

containers. Doing so may cause the battery to generate heat, rupture, or ignite. Using the battery

in this manner may also result in a loss of performance and a shortened life expectancy.

• Do not place the battery on or near fires, stoves, or other high temperature locations.

• DO NOT THROW WATER ON A BURNING LI-ION BATTERY. If an exposed battery does ignite, it

will burn even more violently if it comes into contact with water or even the moisture in air. A fire

extinguisher must be used.

• Do not subject the battery to strong impacts or shocks.

• Do not pierce the battery with nails, strike the battery with a hammer, step on the battery, or

otherwise damage the outer casing.

• MUST re-charge the battery after EACH USE.

• MUST re-charge the battery at least EVERY SIX MONTHS when not in use.

• ALWAYS REMOVE the Battery from the seascooter FOR STORAGE.

• Never leave Lithium-Ion batteries discharged for long - the batteries do self-discharge and the

charge could drop low enough to damage the battery.

• Keep Lithium-Ion batteries away from high heat - high temperatures may cause premature battery failure.

• ALWAYS store Lithium-Ion batteries partially discharged in a cool, dry place.

Replace the battery immediately if it is damaged.

WARNING

BATTERY SAFETY

• MUST re-charge the battery after EACH USE.

• MUST re-charge the battery

at least EVERY SIX MONTHS when not in use.

• ALWAYS REMOVE the Battery from the

seascooter FOR STORAGE.

• Never leave Lithium-Ion batteries

discharged for long - the batteries do

self-discharge and the charge could drop low

enough to damage the battery.

• Keep Lithium-Ion batteries away from high

heat - high temperatures may cause

premature battery failure.

• ALWAYS store Lithium-Ion batteries partially

discharged in a cool, dry place.

RE-CHARGE THE BATTERY

AT LEAST

EVERY

MONTHS

www.seascooter.net

3 4

6789

21 5

BATTERY INSTRUCTION

CHARGING INSTRUCTION:

1. Always ensure the control handles are folded away before removing the battery (see Fig. 1)

2. ALWAYS ensure that the Seascooter is out of the water, dry and placed in a dry area.

3. Pull the two latches down and remove the battery (see Fig. 2)

4. Make sure the battery terminals are dry and clean.

5. Connect the charging base to the charger body. (see Fig. 3)

6. Place the battery onto the charging base. (see Fig. 4)

7. Charging will take around 3 hours. When the Battery Pod is charging, the LED light of the charger turns RED. When the battery is fully charged,

the LED light turns GREEN (see Fig. 5)

8. Once the battery is fully charged, remove it from the charging base. (see Fig. 5)

REPLACING THE BATTERY:

1. Make sure the battery terminals are dry and clean. (see Fig. 6)

2. Make sure the o-rings on the battery terminals are in place. The o-ring must be clean. (see Fig. 7)

3. Align the terminals on the seascooter with the terminals on the battery. (see Fig. 8)

4. Make sure the 2 latches are spread out wide. Slide the battery into the seascooter body according to the Fig. 9

5. Press the battery into the seascooter. Close the latches to lock the battery. (see Fig. 10)

11 12

15 16

Best

Good

Low Medium High

Fully

Charged Battery

Low

40%

Test the machine before first use.

(Note: DO NOT KEEP THE PROPELLERS RUNNING FOR MORE THAN ONE MINUTE IF

IT’S NOT IN THE WATER.)

• Never use this seascooter in sandy water condition. Sands will cause damages to the motors and shorten the lifespan of the unit.

IMPORTANT INFORMATION:

Sand or Grit on Seals

Ensure sand/grit does not get on the seals as correct maintenance and care are essential.

To remove sand or grit, rinse the seals in fresh water and apply fresh lubricant.

If there is sand inside the battery housing, gently brush the sand from the unit taking care

not to scratch the sealing surfaces.

GETTING STARTED

To use the Seascooter, follow these instructions.

1. Follow instructions on page 6 and charge the battery just before use.

2. Place the Seascooter into the water and rock gently to release trapped air.

3. The seascooter unit automatically assumes neutral to positive buoyancy in seawater. It will have less

buoyancy in fresh water and pool and may sink in such waters.

4. Slide the Foldable Control Handles Release Buttons, to fold out the control handles. (see Fig. 11)

5. Make sure the seascooter is in correct position for use. (see Fig. 12)

6. When ready to set off, pull both triggers to start the seascooter (see Fig. 13).

7. Simply push the speed control button to adjust the speed. (see Fig. 14)

8. To stop the Propeller, simply release both triggers.

9. Keep checking the LED light on the battery indicator when using the seascooter. (see Fig. 15)

(Indicator diagram) The battery is full when all the LED lights are on.

(Indicator diagram) The battery capacity drops to 40% when battery indicator shows 2 red lights,

(Indicator diagram) The battery capacity drops to 20% when battery indicator shows 1 red light,

Make sure sufficient charge remains in the battery for returning to the start point.

10. Always ensure the control handles are folded away when the seascooter is out of water. (see Fig. 16)

11. Maintain proper posture to achieve the maximum speed when using the Seascooter. (see Fig. 17)

CAUTION

WARNING

18 19

20 21

Folding away the control handles

1. Press the buttons underneath the control handles (see Fig. 20)

2. Fold away the control handles until you hear a click sound and the control handles are locked. (see Fig. 21)

Do not put your hand or any other things into the propeller.

Note:

1. If there is no operation for a long time, the product will be turned off automatically. Fold away the control handles when not in use.

2. Please do not replace the battery in water. Please remove the battery and clean the machine with fresh water after using, and keep the machine

in cool and ventilated place.

The Q-CLASS foldable control handles can be folded away to achieve a highly compact storage and travelling size. When not in use and with its control

handles folded away the unit features a retractable rubber carry handle that can be easily pulled and pressed back into seascooter body to allow for easy

transport and handling.