Navkom R7 Bedienungsanleitung

INSTRUCTION MANUAL

DOOR PROFILE BUILT-IN CONTROL UNIT

2 3

PLACING YOUR FINGER ON THE SENSOR PROPERLY

Users with smaller ngerprints, especially women and children, may need

to press the nger harder to achieve sucient coverage (applying pressure

spreads your nger).

1YOURFINGERPRINTMUSTCOVERATLEAST 70%OFTHESENSOR

SURFACE.

For most users, this is approximately in the middle of the nger pad, where

the ngerprint curves form the centre. Have a look at your ngerprints and

their features.

2PLACE YOUR FINGER IN THE CENTRE OF THE SENSOR AT THE

AREA WHERE THE FINGERPRINT IS MOST PRONOUNCED.

3DRY SKIN IS THE MOST COMMON CAUSE OF POOR READING.

If the nger needs to be pressed harder than usual to be read, the most

likely cause is dry skin on your nger. This is particularly common during

winter months. Make sure your skin is not unusually dry and use hand cre-

ams or moisturizing wipes or touch a damp surface lightly for this purpose,

but make sure your nger is not wet.

4DO NOT MOVE YOUR FINGER WHILE READING IS IN PROGRESS.

Wait for the device to beep to conrm a successful entry before moving

your nger.

6ENTER EACH USER FINGERPRINT MULTIPLE TIMES! ENTER

SEVERALFINGERSOFBOTHHANDSTOAVOIDPOSSIBLEPROBLEMS

DUE TO INJURED FINGERS.

This ensures a good reading can be taken regardless of the position of your

nger on the sensor and backup is provided in case of a nger injury.

5TO SUCCESSFULLY ENTER YOUR FINGERPRINT, PLACE YOUR

FINGER ON THE SENSOR 3 TIMES.

Only then will your ngerprint be saved. This ensures quality input and

good reading.

TABLE OF CONTENTS

PLACINGYOUR FINGER ON THE SENSOR PROPERLY 3

TECHNICAL DATA 4

MAINTENANCE 4

READER COMPONENTS AND FUNCTIONS 5

DOOR PROFILE BUILT-IN CONTROL UNIT 5

READER CONTROL MODES 6

TEST FUNCTION 6

FINGERPRINT READER SECURITY LOCKDOWN 7

BLUE LIGHT ON/OFF 7

RELAY 2 7

READER CONTROL MODES (door prole built-in control unit) 8

ANALOGUE READER CONTROLWITH DOOR PROFILE BUILT-IN CONTROL UNIT 9

ADMINISTRATOR FINGERPRINTS 9

ANALOGUE CONTROL BY PLACING YOUR FINGER ONTHE SENSOR 13

ADMINISTRATOR FINGERPRINTS 13

FACTORY RESET 15

HYBRID CONTROL 16

APP CONTROL 18

!NAVIGATE TO THE INSTRUCTIONS BY CLICKING ON FIELDS MARKED WITH

4 5

Our ngerprint readers do not require special maintenance, but you must make sure that the sensor is always cle-

an. If the reader is used with greasy or dirty ngers, dirt may start to accumulate on the sensor, which should be

cleaned with a soft, damp cloth. Dirt on the sensor may cause poor performance.

MAINTENANCE

• Capacity: 498 ngerprints (166 × 3)

• Supply voltage: 8-30 V, DC

• 2 relay outputs

• Maximum current on the relay: 3

• Relay trigger time: 1 - 60 s

• Maximum power: 1.8 A in analogue mode, 2.5 A in Wi-Fi mode

• Fast ngerprint recognition: <1.2s

• Operating temperature range: –20°C to +60°C

• Maximum ambient humidity up to: 100% IP65

• Fingerprints remain stored in memory even in the event of a power failure

• Capacitive sensor FPC1011F3

• User interface: 3-colour LED, beeper, 3 buttons on the control unit

• The reader creates a pattern from the biometric characteristics of the ngerprint, which is converted

into a code for ngerprint recognition by a special algorithm.

TECHNICAL DATA

WHENCLEANINGUNDERNOCIRCUMSTANCESUSE:AGGRESSIVECLEANERS,POLISHING

PASTES OR ACIDS! CLEANING OR SCRATCHING THE SENSOR SURFACE WITH HARD AND

SHARP OBJECTS MAY CAUSE DAMAGE TO THE SENSOR AND FAILURE OF THE DEVICE, WHICH

WILL RESULT IN THE WARRANTY BEING VOIDED.

READER COMPONENTS AND FUNCTIONS

BEFORE THE FIRST USE OF YOUR FINGERPRINT READER, IT IS RECOMMENDED TO RESET TO

FACTORY SETTINGS (Test Function remains on for 1 minute – see p. 5 for more info).

ONCE THE FINGERPRINT READER IS RESET, IT IS RECOMMENDED TO IMMEDIATELY ENTER THE

ADMINISTRATOR’S FINGERPRINTS.

IF THERE IS NO ACTIVITY WITHIN 8 MINUTES AFTER CONNECTING THE FINGERPRINT READER,

IT DEACTIVATES AUTOMATICALLY TO PREVENT UNAUTHORISED PERSONS FROM CONNECTING.

IN THIS CASE, TURN OFF THE FINGERPRINT READER POWER SUPPLY FOR MIN. 5 SECONDS (THE

EASIEST WAY TO DO THIS IS TO TURN OFF THE FUSE), THEN TURN THE FINGERPRINT READER

POWER SUPPLY ON AGAIN. IT IS RECOMMENDED YOU RESET THE DEVICE.

IF IT IS IMPOSSIBLE TO ENTER THE ADMINISTRATOR’S FINGERPRINTS IMMEDIATELY

AFTER CONNECTING THE FINGERPRINT READER, PLEASE TURN OFF THE POWER OF YOUR

FINGERPRINT READER UNTIL THE ADMINISTRATOR’S FINGERPRINTS ARE ENTERED.

1MULTICOLOUR LED

2FINGERPRINT SENSOR

Uses various colour signals for communicating the device’s

status and operations running.

When no operation is running, placing the saved nger on the

sensor opens the door.

3BEEPER

While an operation is running, light signals are accompanied by

sound.

DOOR PROFILE BUILT-IN CONTROL UNIT

The control unit is located in the door prole, next to the door loop. There are two function buttons

(1 and 2), and the R button for factory reset (located under the screw).

BUTTON 1

Analogue mode: ADDING ADMINISTRATORS OR USERS

Wi- mode: ACTIVATION/DEACTIVATION OF FREE PASSAGE

MODE

BUTTON 2

Analogue mode: DELETING USERS

Wi- mode: BLUE LIGHTING ON/OFF

BUTTON R

Factory reset.

To press this button, rst remove the screw. The button is

located under the screw.

6 7

No matter which control unit you have, when using the reader for the rst time, you can choose between three

dierent control modes: analogue, app or hybrid control. Description and instructions for each control mode can

be found below.

ANALOGUE CONTROL using buttons located on the control unit, by remote control or by placing your

nger on the sensor

APP CONTROL on your smartphone

HYBRID CONTROL - analogue reader control, using the app only to unlock doors and control LED lighting

READER CONTROL MODES

YOU CAN CHANGE THE CONTROL MODE AT ANY TIME BY RESETTING THE DEVICE TO FACTORY

SETTINGS AND STARTING TO OPERATE IT IN YOUR PREFERRED MODE.

Resetting the device to factory settings deletes the ngerprint database and all other settings.

In the event that a nger is placed on the sensor of the ngerprint reader seven times in a row, the reader will

not recognize it and will lock for 30 seconds.

After thirty seconds, the reader will be ready to be used again. The reader will lock again if a ngerprint which

cannot be recognized by the reader is placed on the sensor again seven times in a row. This time it will lock for

60 seconds.

After each unsuccessful attempt, up to seven attempts, the reader will be locked and the time will increase by 30

seconds, up to a maximum of 5 minutes. Each time the reader successfully recognizes a ngerprint, the count is

interrupted and resets to the beginning.

FINGERPRINT READER SECURITY LOCKDOWN

The test function is interrupted by a power outage or the addition of ngerprints.

Once the test function has elapsed, the device remains at factory settings and ready

for rst use.

TEST FUNCTION

GREEN

AFTER EACH FACTORY RESET, THE DEVICE REMAINS IN TEST FUNCTION FOR 1

MINUTE.

During this time, the sensor-LED ashes green.

DURING THIS TIME, ANY FINGERPRINT CAN UNLOCK THE DOOR.

WHILE THE READER IS LOCKED, THE PURPLE LED WILL FLASH AND THE READER WILL NOT

RESPOND TO FINGERPRINTS. PURPLE

PRESS AND HOLD THE RBUTTON FOR 10 SECONDS. THE

PURPLE LED BLINKS 5 TIMES ACCOMPANIED BY FIVE BEEPS.

All ngerprints, including the administrator’s, are erased from the

memory and the device is restored to factory settings. Any paired re-

mote controls and smartphones are disconnected as well.

In combination with the control unit built in the door prole, our ngerprint readers allow you to unlock additi-

onal (side or garage) doors, as well as the door the reader is installed in. Individual ngerprints can be assigned

to either open the additional door only or the main and additional door together.

To activate relay 2 with the selected ngerprint, complete the Optional step for activating relay 2 when

entering the ngerprint (both administrator and user), which is described in the Input procedures for admi-

nistrators and users section.

SKIP THIS STEP, IF YOU WANT THE FINGERPRINTTO OPEN THE FRONT DOOR ONLY.

The blue LED starts ashing immediately. Wait for three beeps before you release

the button.With this operation, only the blue LED that is lit in standby mode is turned

o. All other light signals remain active. Repeat the procedure to reactivate the blue

LED.

HOLD DOWN BUTTON 1 ON THE CONTROL UNIT FOR 10 SECONDS AND

WAIT FOR THE DEVICE TO BEEP 3 TIMES. THE BLUE LED TURNS OFF.

BLUE LIGHT ON/OFF

RELAY 2

FACTORY RESET

PURPLE

5 ×

If you are bothered by the blue LED that is constantly lit in standby mode, you can turn it

o.

AFTER EACH FACTORY RESET, THE DEVICE REMAINS IN TEST FUNCTION FOR 1 MINUTE.

8 9

ANALOGUE READER CONTROL WITH DOOR PROFILE BUILT-IN

CONTROL UNIT

Start by adding administrator ngerprints on the reader by pressing Button 1 on the control unit.

Perform the factory reset.

The rst three saved ngerprints have a special role and are called administrator ngerprints. These

ngerprints are entered by the administrator, i.e. the device owner. From the third memory spot onwards, only

user ngerprints can be entered. Entering ngerprints without the presence of an administrator is no longer

possible beyond the three memory spots.

ADMINISTRATORS

234 5 6 7 8 9 10

1. THE ADMINISTRATOR FINGERPRINTS ARE ONLY THE FIRST THREE FINGERPRINTS STORED IN THE

MEMORY

No further administrator ngerprints can be added after the rst three. Administrator ngerprints can be

three dierent ngers of the same person or ngerprints of dierent persons.

2. WHEN THE FIRST THREE MEMORY SPOTS ARE FILLED, ONLY USERS CAN BE ENTERED.

3. ADMINISTRATOR FINGERPRINTS SHOULD BE CAREFULLY CHOSEN, AND THE FINGERPRINTS

SHOULD BE CLEAR.

You need to be especially careful when entering administrator ngerprints, as these ngerprints cannot be

entered later, and can only be deleted by RESETTING TO FACTORY SETTINGS..

When entering the administrator ngerprint, select an uninjured nger with the clearest ngerprint.While

entering the ngerprints, keep your ngers clean and suciently moist, and for good readings follow the

instructions in the section PLACINGYOUR FINGER ONTHE SENSOR PROPERLY.

4. ADMINISTRATOR FINGERPRINTS ALSO OPEN DOORS AND ACTIVATE RELAY 2

The only dierence between the administrator and user ngerprint role is that administrator can perform

input and deletion operations.

5. WHEN THE READER MEMORY IS EMPTY, FINGERPRINTS CAN BE ENTERED BY ANYONE, SO

ADMINISTRATOR FINGERPRINTS SHOULD BE ENTERED AS SOON AS THE DEVICE IS INSTALLED TO

PROTECT IT AGAINST UNAUTHORIZED ACCESS.

USERS

ADMINISTRATOR FINGERPRINTS

Start by entering administrator ngerprints on the reader/by pressing Button 1 on the control unit/

Button A on the remote control.

READER CONTROL MODES (door prole built-in control unit)

When using the reader for the rst time, you can choose between three dierent control modes: analogue, app

or hybrid control. To choose the control mode, simply start using the reader in your preferred mode.

ANALOGUE CONTROL

is simple and allows basic functions. Analogue control is can be activated in 3 ways:

Find, name and add your reader in the X-Manager app.

APP CONTROL

provides a wide range of functions.

Click on its name to establish a connection.

Start entering administrator ngerprints in the app.

Find, name and add your reader in the X-Manager app.

HYBRID CONTROL

is an analogue reader control using the app only to unlock doors and control LED lighting.

Start by entering administrator ngerprints on the reader/by pressing Button 1 on the control unit/

Button A on the remote control.

Once the administrator’s ngerprints are entered, you can use the app only to unlock the door or

manage the LED lighting.

YOU CAN CHANGE THE CONTROL MODE AT ANY TIME BY RESETTING THE DEVICE TO FACTORY

SETTINGS AND STARTING TO OPERATE IT IN YOUR PREFERRED MODE.

Resetting the device to factory settings deletes the ngerprint database and all other settings.

WITH BUTTONS ON CONTROL UNIT

USE OF X-MANAGER APP

HYBRID CONTROL

WITH REMOTE CONTROL

ON THE SENSOR

10 11

1PRESS BUTTON 1 ON THE CONTROL UNIT TO

START THE ADMINISTRATOR FINGERPRINTS ENTRY

PROCEDURE.

The blue LED starts ashing.

2a IF YOU WANT THE ADMINISTRATOR FINGERPRINT TO ACTIVATE RELAY 2,

PRESS BUTTON 1.

2b IF YOU WANT THE ADMINISTRATOR FINGERPRINT TO SIMULTANEOUSLY

OPEN THE DOOR AND ACTIVATE RELAY 2, PRESS BUTTON 2.

OPTIONAL STEP FOR RELAY 2 ACTIVATION

IF YOU DON'T WANT TO ACTIVATE RELAY 2, SKIP THIS STEP

The orange LED will ash once and you will hear a beep. The entered administrator nger-

print will only activate relay 2.

The orange LED will ash twice and you will hear two beeps. The entered administrator n-

gerprint will open the door and activate relay 2 at the same time.

BLUE

ORANGE

1 ×

ORANGE

2 ×

3PLACE THE ADMINISTRATOR FINGER ON THE SENSOR

3 TIMES IN A ROW. EACH SUCCESSFUL ENTRY WILL BE

CONFIRMED WITH A SHORT BEEP. AFTER 3 ENTRIES, THE

FINGERPRINT IS SAVED - A LONG BEEP IS HEARD AND

THE GREEN LED LIGHTS UP.

GREEN

1 ×

ADMINISTRATOR FINGERPRINTS ENTRY PROCEDURE

3 ×

4REPEAT THE PROCEDURE WITH THE SECOND AND

THIRD ADMINISTRATOR FINGERS.

IF THE FINGERPRINT YOU ARE TRYING TO

ENTER IS TOO DAMAGED AND DOES NOT HAVE

A CLEAR ENOUGH STRUCTURE, THE RED LED WILL

LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE

OPERATION WILL BE STOPPED. CHOOSE A HIGH

QUALITY FINGERPRINT, MAKE SURE THE FINGER IS

CLEAN AND MOIST ENOUGH AND REPEAT THE

PROCESS. FOR EACH FINGERPRINT YOU WANT TO

SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR

TO ENSURE GOOD FINGERPRINT RECOGNITION.

1TOSTARTTHEUSERFINGERPRINTSENTRYPROCEDURE,

PRESS BUTTON 1ON THE CONTROL UNIT.

The blue LED starts ashing.

OPTIONAL STEP FOR RELAY 2 ACTIVATION

IF YOU DON'T WANT TO ACTIVATE RELAY 2, SKIP THIS STEP

BLUE

GREEN

1 ×

GREEN

1 ×

2FIRST, THE ADMINISTRATOR PLACES A FINGER ON THE

SENSOR.

For security reasons, the administrator must always conrm the

start of the user entry procedure.

After successful administrator recognition, the green LED will light

up and a beep will be heard.

If a non-administrative nger is placed on the sensor, the

device will not react and the blue LED will keep ashing. BLUE

Follow the instructions on the previous page.

3THE BLUE AND GREEN LEDS FLASH ALTERNATELY.

PLACE THE USER FINGERPRINT ON THE SENSOR 3

TIMES IN A ROW. EACH SUCCESSFUL ENTRY WILL BE

CONFIRMED WITH A SHORT BEEP. AFTER 3 ENTRIES,

THE FINGERPRINT IS SAVED - A LONG BEEP IS HEARD

AND THE GREEN LED LIGHTS UP.

BLUE

GREEN

USER FINGERPRINTS ENTRY PROCEDURE

3×

IF THE FINGERPRINT YOU ARE TRYING TO

ENTER IS TOO DAMAGED AND DOES NOT HAVE

A CLEAR ENOUGH STRUCTURE, THE RED LED WILL

LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE

OPERATION WILL BE STOPPED. CHOOSE A HIGH

QUALITY FINGERPRINT, MAKE SURE THE FINGER IS

CLEAN AND MOIST ENOUGH AND REPEAT THE

PROCESS. FOR EACH FINGERPRINT YOU WANT TO

SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR

TO ENSURE GOOD FINGERPRINT RECOGNITION.

12 13

1×

1TO START THE USER FINGERPRINTS DELETION

PROCEDURE, PRESS BUTTON 2ON THE CONTROL UNIT.

The blue LED starts ashing.

2FIRST, THE ADMINISTRATOR PLACES A FINGER ON THE

SENSOR.

For security reasons, the administrator must always conrm the

start of the user deletion procedure.

After successful administrator recognition, the green LED will light

up and a beep will be heard.

If a non-administrative nger is placed on the sensor, the

device will not react and the blue LED will keep ashing.

3GREEN AND RED LEDS WILL FLASH ALTERNATIVELY.

PLACE THE USER FINGER YOU WANT TO DELETE ON THE

SENSOR ONCE.

When the nger is successfully deleted, the LED will light

up 3 times and three beeps will be heard.

BLUE

GREEN

1 ×

BLUE

RED

GREEN

ORANGE

3 ×

USER FINGERPRINTS DELETION PROCEDURE

If a nger that is not saved in the memory is placed on

the sensor, the device will not react. The green and red

LEDS will continue ashing.

IF MORE THAN 1 FINGERPRINT OF THE SAME USER

IS SAVED, DELETE THE FINGERPRINTS OF ALL

FINGERS!

ANALOGUE CONTROL BY PLACING YOUR FINGER ON THE

SENSOR

Start by adding administrator ngerprints by placing your nger on the sensor for 5 seconds.

Perform the factory reset.

The rst three saved ngerprints have a special role and are called administrator ngerprints. These

ngerprints are entered by the administrator, i.e. the device owner. From the third memory spot onwards, only

user ngerprints can be entered. Entering ngerprints without the presence of an administrator is no longer

possible beyond the three memory spots.

ADMINISTRATORS

234 5 6 7 8 9 10

USERS

ADMINISTRATOR FINGERPRINTS

1. THE ADMINISTRATOR FINGERPRINTS ARE ONLY THE FIRST THREE FINGERPRINTS STORED IN THE

MEMORY

No further administrator ngerprints can be added after the rst three. Administrator ngerprints can be

three dierent ngers of the same person or ngerprints of dierent persons.

2. WHEN THE FIRST THREE MEMORY SPOTS ARE FILLED, ONLY USERS CAN BE ENTERED.

3. ADMINISTRATOR FINGERPRINTS SHOULD BE CAREFULLY CHOSEN, AND THE FINGERPRINTS

SHOULD BE CLEAR.

You need to be especially careful when entering administrator ngerprints, as these ngerprints cannot be

entered later, and can only be deleted by RESETTING TO FACTORY SETTINGS..

When entering the administrator ngerprint, select an uninjured nger with the clearest ngerprint.While

entering the ngerprints, keep your ngers clean and suciently moist, and for good readings follow the

instructions in the section PLACINGYOUR FINGER ONTHE SENSOR PROPERLY.

4. ADMINISTRATOR FINGERPRINTS ALSO OPEN DOORS AND ACTIVATE RELAY 2

The only dierence between the administrator and user ngerprint role is that administrator can perform

input and deletion operations.

5. WHEN THE READER MEMORY IS EMPTY, FINGERPRINTS CAN BE ENTERED BY ANYONE, SO

ADMINISTRATOR FINGERPRINTS SHOULD BE ENTERED AS SOON AS THE DEVICE IS INSTALLED TO

PROTECT IT AGAINST UNAUTHORIZED ACCESS.

14 15

IN THIS CONTROL MODE, INDIVIDUAL FINGERPRINTS CANNOT BE DELETED. YOU CAN

ONLY DELETE THE ENTIRE FINGERPRINT DATABASE (INCLUDING ADMINISTRATORS) BY

RETURNING THE DEVICE TO FACTORY SETTINGS.

1TO START ENTERING ADMINISTRATOR FINGERPRINTS, PLACE YOUR FINGER

ON THE SENSOR FOR 5 SECONDS.

The blue LED starts ashing. BLUE

2 PLACE THE ADMINISTRATOR FINGERPRINT ON THE

SENSOR 3 TIMES IN A ROW. EACH SUCCESSFUL ENTRY

WILL BE CONFIRMED WITH A SHORT BEEP. AFTER THREE

ENTRIES, THE FINGERPRINT IS SAVED - A LONG BEEP IS

HEARD AND THE GREEN LED LIGHTS UP.

GREEN

1 ×

ADMINISTRATOR FINGERPRINTS ENTRY PROCEDURE

3 ×

3 PLACE THE FIRST ADMINISTRATOR FINGER ON THE SENSOR FOR 5 SECONDS,

THEN ENTER THE SECOND ADMINISTRATOR FINGER 3 TIMES IN THE SAME WAY AS

THE PREVIOUS ONE.

4REPEAT THE SAME PROCEDURE WITH THE THIRD ADMINISTRATOR FINGER.

IF THE FINGERPRINT YOU ARE TRYING TO

ENTER IS TOO DAMAGED AND DOES NOT HAVE

A CLEAR ENOUGH STRUCTURE, THE RED LED WILL

LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE

OPERATION WILL BE STOPPED. CHOOSE A HIGH

QUALITY FINGERPRINT, MAKE SURE THE FINGER IS

CLEAN AND MOIST ENOUGH AND REPEAT THE

PROCESS. FOR EACH FINGERPRINT YOU WANT TO

SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR

TO ENSURE GOOD FINGERPRINT RECOGNITION.

The blue and green LEDs ash alternately.

GREEN

1 ×

USER FINGERPRINTS ENTRY PROCEDURE

1TO START ENTERING USER FINGERPRINTS, PLACE THE ADMINISTRATOR

FINGER ON THE SENSOR FOR 5 SECONDS.

BLUE

GREEN

PURPLE

5 ×

BLUE

RED

The blue and red LEDs ash alternately.

3 ×

FACTORY RESET

1 PLACE THE ADMINISTRATOR FINGER ON THE SENSOR

FOR 15 SECONDS.

2CONFIRM THE FUNCTION BY PLACING THE ADMINISTRATOR FINGER ON THE

SENSOR TWO TIMES. THE PURPLE LED BLINKS 5 TIMES ACCOMPANIED BY 5

BEEPS.

* If the administrator’s ngerprint has not yet been entered, the reset can be done with any nger

within 8 minutes after the rst connection. In this case, the blue LED turns o.

All ngerprints, including the administrator’s, are deleted from the memory and the device

is restored to factory settings. Any paired remote controls are deleted as well.

3PLACE THE USER FINGERPRINT ON THE SENSOR

3 TIMES IN A ROW. EACH SUCCESSFUL ENTRY WILL

BE CONFIRMED WITH A SHORT BEEP. AFTER THREE

ENTRIES, THE FINGERPRINT IS SAVED - A LONG BEEP IS

HEARD AND THE GREEN LED LIGHTS UP.

IF THE FINGERPRINT YOU ARE TRYING TO

ENTER IS TOO DAMAGED AND DOES NOT HAVE

A CLEAR ENOUGH STRUCTURE, THE RED LED WILL

LIGHT UP, THE DEVICE WILL BEEP 5 TIMES AND THE

OPERATION WILL BE STOPPED. CHOOSE A HIGH

QUALITY FINGERPRINT, MAKE SURE THE FINGER IS

CLEAN AND MOIST ENOUGH AND REPEAT THE

PROCESS. FOR EACH FINGERPRINT YOU WANT TO

SAVE, PLACE THE FINGER 3 TIMES ON THE SENSOR

TO ENSURE GOOD FINGERPRINT RECOGNITION.

16 17

Add your reader in the X-Manager app.

Perform the factory reset.

Start by entering administrator ngerprints on the reader/by pressing Button 1 on the control unit/

Button A on the remote control.

HYBRID CONTROL

FINGERPRINT ENTRY AND READER CONTROL

Once the administrator’s ngerprints are entered, you can use the app only to unlock the door or manage

the LED lighting.

Download the X-manager app to your smartphone or tablet from the Google Play Store

(Android) or the App Store (Apple).

CONNECTING THE PHONE TO THE READER

APP FUNCTIONS

Pressing the Activate- relay2 tabwill activate

the device connected to relay 2 (alarm, garage

door, side door, etc).

Pressing the Touch to open - relay 1 tab will

unlock the door.

LED settings: If there is LED lighting in the

door, it can be connected to the system and

controlled by the X-manager. It is possible to

adjust the brightness (1% to 100%) and the

schedule for turning the lighting on/o:

- 24H: The LED lighting will be switched on

continuously.

- Auto: The LED lighting will automatically turn

on at sunset and turn o at sunrise.

- Custom:You can set the switch-on and switch-

o times yourself. You can set two intervals in

the day when the lighting will be on.

Relay opening time: The length of time

during which the relay is switched on can be

adjusted to between 1 and 60 seconds. This

setting is useful when using an electric strike.

Blue backlight: if the blue backlight that

lights up when the reader is in standby mode

bothers you, you can turn it o.

Once the ngerprints are entered, you can connect to the reader and control both relays and LED settings

in the app.

APPLE

ANDROID

ON THE SENSOR

WITH REMOTE CONTROL

WITH BUTTONS ON CONTROL UNIT

18 19

APP CONTROL

IMMEDIATELYAFTERINSTALLINGANDCONNECTINGTHEDEVICE,ITISRECOMMENDED

TOCONNECT ATLEAST 1 PHONEWITHTHE DEVICE.OTHERWISEWI-FI IS DEACTIVATED

AFTER 8 MINUTES FOR SECURITY REASONS. IN THIS CASE, THE DEVICE MUST BE

DISCONNECTED FROM THE POWER SUPPLY AND CONNECTED AGAIN BEFORE BEING

CONNECTED TO THE PHONE FOR THE FIRST TIME.

X-manager

Download the X-manager app to your smartphone or tablet from the Google Play Store

(Android) or the App Store (Apple).

Find, name and add your reader in the X-Manager app.

Click on the name to establish a connection.

Start entering administrator ngerprints in the app.

Perform the factory reset.

ON/OFF FREE ENTRANCE MODE

1TO ACTIVATE, PRESS BUTTON 1ON THE CONTROL UNIT.

The blue LED starts ashing.

BLUE

GREEN

2THE ADMINISTRATOR CONFIRMS THE OPERATION WITH

THEIR FINGERPRINT.

AS LONG AS THE FREE ENTRANCE MODE IS ON, THE GREEN

LED REMAINS ON.

Hold button 1 until the green LED is replaced by the blue one. BLUE

For security reasons, the administrator must always conrm the

operation.

3TODEACTIVATE,PRESS BUTTON1ONTHE CONTROLUNIT.

BLUE LIGHTING ON/OFF

BLUE

FACTORY RESET

The purple LED ashes 5 times and you hear 5 beeps. All

ngerprints stored in the memory, including administrator

ngers, will be erased and the device will be reset to factory

settings.

TO PRESS THIS BUTTON, FIRST REMOVE THE SCREW. THE

BUTTON IS LOCATED UNDER THE SCREW. PRESS AND

HOLD THE RBUTTON FOR 10 SECONDS. PURPLE

5 ×

HOLD BUTTON 2 UNTIL THE BLUE LED IS TURNED ON/OFF.

BUTTON FUNCTIONS on the door prole built-in control unit

If you have a door prole built-in control unit, but you wish to operate the reader using the app, buttons 1 and 2

will serve as shortcuts to turn on/o the free passage mode and blue lighting.

Inhaltsverzeichnis

Andere Navkom Steuereinheit Handbücher

Navkom

Navkom BBX MINI Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung