Naxa NCA-604 Bedienungsanleitung

-1-

Content

Installation steps...........................................................................

General information about remote control......................................

1. Removing insulating sheet.........................................................

2. Replacing the lithium cell...........................................................

3. Note about using the remote control...........................................

4. Warning about lithium cells of remote control.............................

Locations and Names of controls...................................................

1. Locations and Names of controls on main unit............................

2. Locations and Names of controls on remote control...................

General operation...........................................................................

Radio operation.............................................................................

Disc/USB/card operation............ ...................................................

1. Loading or unloading a disc, USB or card..................................

1.1 Loading a disc, USB or card.....................................................

1.2 Unloading a disc, USB or card..................................................

2. Function of controls on main unit or remote control..................

AUX IN operation...........................................................................

Troubleshooting............................................................................

Specifications...............................................................................

INSTALLATION STEPS

1. Remove 2 screws for protecting deck;

1) Remove chassis from the Slide Bracket Housing as follows:

2) Remove 2 screws protecting the deck as

right;

2. Connecting all wires

1) Slide Bracket Housing;

2) Remove the control panel from the chassis as follows:

A. Press REL button to detach the control panel .

B. Hold the right end of the control panel to pull rightward

illustrated on the

Re-insert the chassis into the

a little and then remove it

REL button

PLASTIC TRIM OUT

KEY PLATE

If you want to remove the chassis from the Slide Bracket Housing , first remove the

Plastic trim from both sides, then insert 2 Key Plates into the left and the right side of

the chassis as illustrated.

-2-

-3-

3) Connect all wires as follows:

RADIO ANTENNA JACK FRONT AUDIO OUT RCA JACK R (red)

FRONT AUDIO OUT RCA JACK L (white)

REAR AUDIO OUT RCA JACK L (white)

REAR AUDIO OUT RCA JACK R (red)

The Description of the Fixed ISO Female Connector

CONNECTOR A

4. Memory +12V

5. Auto Antenna

7. 12V (To Ignition Key)

8. GROUND

CONNECTOR B

1. Rear Right Speaker (+)

2. Rear Right Speaker (-)

3. Front Right Speaker (+)

4. Front Right Speaker (-)

5. Front Left Speaker (+)

6. Front Left Speaker (-)

7. Rear Left Speaker (+)

8. Rear Left Speaker (-)

FUSE

Fixed ISO Female Connector

4) Attaching the control panel onto the chassis.

A. Align and thrush the bulge of the control panel into the hollow of the chassis.

B. Push the right end of the control panel to the chassis till a click sound is heard.

* How to clean panel connector

Frequent detachment will cause the panel connectors to deteriorate. To minimize

deterioration, periodically wipe the panel connector with a clean/soft/dry cloth .

5) Test to make sure that it works properly.

3. Instal the main unit according to the installation diagram on the next page:

1) Mount the main unit in A/V position in vehicle.

2) Bend tabs of the sliding metal housing where necessary to ensure that

the front part of main unit is fixed;

3) Use a metal strap to fix the rear part of the chassis.

* Uninstalling the main unit:

1) Remove the metal strap from the main unit;

2) Remove the plastic trim frame from the main unit;

3) Insert a key plate into the left and the right side of the main unit and draw the

main unit out of the sliding metal housing.

Bulge

Hollow

Panel Connector

-4-

-5-

Installation diagram

DASH BOARD

METAL MOUNTING

STRAP

HEX NUT

SPRING WASHER

PLAIN WASHER

TAPPING SCREW

CONSOLE

SLIDE BRACKET

HOUSING

HEX BOLT

-6-

General information about the remote control

1. Removing insulating sheet

The remote control comes with an insulating

sheet attached to the underside of the remote

control as illustrated on the right

The remote control is disabled and will not work

until the insulating sheet is removed.

as illustrated on the right

2. Replacing the lithium cell

If the electric energy of the lithium cell is weak,

replace it .

1. Press and hold the movable block in the

direction indicated by arrow 1 , at the same

time pull the cell holder out of the remote control

in the direction indicated by arrow 2 .

2. Replace the old cell with a new one with (+)

polarity side upward .

3. Insert the cell holder into the remote control again.

3. Note about using the remote control

1. Face the emitting window of the remote control towards the sensor window of

the unit.

2. Operation angle for front panel: About 30 degrees

3. The distance between the emitting window of the remote control and the sensor

window of the unit : < 5M .

4. Warning for lithium cells of remote control

leakage may cause damage to remote control.1.Cell

2.Do not throw cells into fire, it may cause an explosion.

3.To avoid accidents, keep cells out of reach of children.

Locations and Names of controls

1. Locations and Names of controls on main unit

-7-

1823

1. REL button

2. PWR button

3. SEL button and VOL knob

4. BAND or ID3 button

5. EQ button

6. APS button

7. MUTE button

8. >|| or 1 button

9. INT or 2 button

10.RPT or 3 button

11.RDM or 4 button

12.-10 or 5 button

13.+10 or 6 button

14. |<< button

15. >>| button

16. MODE button

17. EJECT button

18. RESET button

19. IR sensor window

20. AUX IN jack

21. USB port

22. LCD screen

23. Card slot

24. CLK button

25. Disc slot

Control Panel

Front side of chassis after removing control panel

76 9814

15 17

10 11 12 13

2. Locations and Names of controls on remote control

-8-

PWR

MUTE

VOL-

SEL

ENTER

LOUD

VOL+

LOC

MOD DISP

ID3

BAND

APS

SCAN

123

456

/TOP

INT

-10

RPT

RDM

+10

1. PWR button

2. < button

3. LOUD button

4. VOL- button

5. LOC/DX button

6. ID3 or BAND button

7. APS or SEARCH button

8. >|| or TOP or 1 button

9. RDM or 4 button

10.INT or 2 button

11. VOL+ button

12. MUTE button

13. SEL or ENTER button

14. > button

15. ST/MO button

16. DISP button

17. MODE button

18. SCAN button

19. RPT or 3 button

20. +10 or 6 button

21. -10 or 5 button

General Operation

1. PWR button

To power main unit on or off.

2. VOL knob or VOL+ & VOL- button

To increase or decrease volume level.

3. MUTE button

To cancel or resume sound.

4. SEL button

5. EQ button

To select a desired preset EQ mode from POP, ROCK, CLASSIC, FLAT and OFF.

6. LOUD button

To switch LOUD mode on or off.

7. DISP or CLK button

To display clock time, briefly press the DISP or CLK button.

To set clock time, first long press the DISP or CLK button to flash hour, and rotate

the VOL knob or press the VOL+ or VOL- button to adjust the hour; then briefly

press the SEL button to flash minute, and rotate the VOL knob or press the VOL+

or VOL- button to adjust the minutes; finally press the DISP or CLK button to con-

firm it.

8. MODE button

To switch on a work source between RADIO, DISC, USB, CARD and AUX IN.

9. REL button

To detach the control panel from chassis.

10. RESET button

To reset all parameters to factory default values.

* When LCD does not display normally or sound is distorted or some controls are

disabled, press the REL button to detach the control panel from chassis and re-

move the control panel from the chassis, then use a subject with a sharp point

end to thrush the RESET hole.

To switch between BAS(bass), TRE(treble), BAL(balance), FAD(fader), EQ,

BEEP, LOUD, MONO/STEREO(in radio mode), LOC/DX(in radio mode) and

VOL(volume), press the SEL button repeatedly. After selecting a desired mode,

rotate the VOL knob or press the VOL+ or VOL- button to set it.

-9-

Andere Handbücher für NCA-604

Andere Naxa Autoempfänger Handbücher

Naxa

Naxa NCA-649 Bedienungsanleitung

Naxa

Naxa NCD-707 Bedienungsanleitung

Naxa

Naxa NCA-696 Bedienungsanleitung

Naxa

Naxa NCD-694 Bedienungsanleitung

Naxa

Naxa NCD-701 Bedienungsanleitung

Naxa

Naxa NCA-675 Bedienungsanleitung

Naxa

Naxa NCA-613 Bedienungsanleitung

Naxa

Naxa NCA-681 Bedienungsanleitung

Naxa

Naxa NCD-694 Bedienungsanleitung

Naxa

Naxa NCD-691 Bedienungsanleitung

Naxa

Naxa NCA-610 Bedienungsanleitung

Naxa

Naxa NCA-606 Bedienungsanleitung

Naxa

Naxa NCA-607 Bedienungsanleitung

Naxa

Naxa NCA-676 Bedienungsanleitung

Naxa

Naxa NCD-650 Bedienungsanleitung

Naxa

Naxa NCA-677 Bedienungsanleitung

Naxa

Naxa NX-671 Bedienungsanleitung

Naxa

Naxa NCA-602 Bedienungsanleitung

Naxa

Naxa NCA-671 Bedienungsanleitung

Naxa

Naxa NCD-702 Bedienungsanleitung

Naxa

Naxa NCA-678 Bedienungsanleitung

Naxa

Naxa NCA-608 Bedienungsanleitung

Naxa

Naxa NCD-691 Bedienungsanleitung

Naxa

Naxa NCA-605 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

JVC

JVC KD-AHD69 Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung