NCR 7448 Workstation Betriebsanleitung

NCR 7448 Workstation

Release 1.3

Site Preparation

B005-0000-1201

Issue D

The product described in this book is a licensed product of NCR Corporation.

NCR is a registered trademark of NCR Corporation.

It is the policy of NCR Corporation (NCR) to improve products as newtechnology, components, software, and firmware

become available. NCR, therefore, reserves the right to change specifications without prior notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some

instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR

representative or NCR office for information that is applicable and current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of

this book.

Address correspondence to:

Manager, Information Products

NCR Corporation

2651 Satellite Blvd.

Duluth, GA 30096

By NCR Corporation

Dayton, Ohio U.S.A.

Site Preparation i

Preface

Audience

This is a contractual document. It contains important warnings and confers

important legal rights and obligations. You are advised to read it carefully.

It is the responsibility of the customer to ensure that all installation preparations

are complete and in compliance with NCR specifications and requirements and

all applicable national, state, or local codes, regulations, and laws.

Safety Warnings

The NCR 7448 Workstation must be connected to an AC outlet that is near the

workstation and is easily accessible by the operator.

Warning: This unit contains hazardous voltages and should only be

serviced by qualified service personnel.

The power switch is a logic switch only. The AC line voltage primaries are live

at all times when the power cord is connected. Therefore, disconnect the AC

power cord before opening the unit to install features or service this

workstation.

ii Site Preparation

Fuse Replacement

Caution: For continued protection against risk of fire, replace only with the

same type and ratings of fuse.

Attention: Pour prévenir et vous protéger contre un risque de feu, remplacer la

fusible avec une autre fusible de même type, seulement.

Power Supply Cord Used as Disconnect Means

Caution: The power supply cord is used as the main disconnect device. Ensure

that the socket outlet is located/installed near the equipment and is easily

accessible.

Attention: Le cordon d'alimentation est utilisé comme interrupteur général. La

prise de courant doit être située ou installée å proximité du matériel et être facile

d'accés.

Warning: DO NOT connect or disconnect the transaction printer while the

workstation is powered on. This can result in system or printer damage.

Lithium Battery Warning

Caution: Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type as recommended by the manufacturer. Discard

used batteries according to the manufacturer's instructions.

Site Preparation iii

Attention: Il y a danger d’explosion s’il y a remplacement incorrect de la

batterie. Remplacer uniquement avec une batterie du même type ou d’un type

recommandé par le constructeur. Mettre au rébut les batteries usagées

conformément aux instructions du fabricant.

Peripheral Usage

The NCR 7448 Workstation should only be used with peripheral

devices which are certified by the appropriate safety agency for the

country of installation (UL, CSA, TUV, VDE) or those which are

recommended by NCR Corporation.

Environmental Consciousness

NCR's concern for the environment is demonstrated by the

intelligent power management system of the NCR 7448 Workstation

which operates efficiently in a standalone or network environment.

Ni-Cad Battery Warning

Caution:

USA and CANADA:

The product you have purchased contains a rechargeable battery.

The battery is recyclable.At the end of its useful life, under various

state and local laws it may be illegal to dispose of this battery into

the municipal waste stream. Check with your local municipality or

sold waste officials for recycling options or proper disposal.

iv Site Preparation

European countries (Austria, Denmark, Finland, Germany, Ireland, Italy,

Luxembourg, Netherlands, Portugal, Spain, Sweden, United Kingdom,

Belgium, Iceland, Liechtenstein, Norway and Switzerland):

a) Nach Gebrauch der Verkaufsstello zurückgoben

b) Après usage à rapporter au point de vente

c) Ritornare la pila usate al negozio

d) Contain Nickel-Cadmium battery. Must be recycled or disposed of

properly.

About this Book

This book provides site preparation information for NCR 7448 Workstation

components. Peripheral component and AC wiring site preparation information

is NOT provided in this book. The associated reference documents are listed in

the “Related Site Preparation Data” section.

Site Preparation v

Table of Contents

NCR 7448 SITE PREPARATION

NCR 7448 SITE PREPARATIONNCR 7448 SITE PREPARATION

NCR 7448 SITE PREPARATION................................

................................................................

.................................

TYPICAL 7448 WORKSTATION CONFIGURATIONS........................................... 2

INTERPRETING THE MODEL NUMBER............................................................ 4

RELATED SITE PREPARATION DATA ............................................................... 5

AC Power and Communications Wiring ................................................. 5

Peripherals................................................................................................ 5

HOW TO ORDER.............................................................................................. 6

CUSTOMER RESPONSIBILITIES

CUSTOMER RESPONSIBILITIESCUSTOMER RESPONSIBILITIES

CUSTOMER RESPONSIBILITIES ................................

................................................................

.............................................................

..........................................................

.............................8

STORE WIRING REQUIREMENTS

STORE WIRING REQUIREMENTSSTORE WIRING REQUIREMENTS

STORE WIRING REQUIREMENTS ................................

................................................................

...........................................................

......................................................

...........................9

AC WIRING.................................................................................................... 9

LAN COMMUNICATIONS................................................................................ 9

SYSTEM CONFIGURATION DIAGRAM

SYSTEM CONFIGURATION DIAGRAMSYSTEM CONFIGURATION DIAGRAM

SYSTEM CONFIGURATION DIAGRAM................................

................................................................

..................................................

....................................

..................10

1010

PHYSICAL CONSIDERATIONS

PHYSICAL CONSIDERATIONSPHYSICAL CONSIDERATIONS

PHYSICAL CONSIDERATIONS................................

................................................................

...............................................................

..............................................................

............................... 11

1111

HANDLING SYSTEM COMPONENTS................................................................11

OPERATING AND SERVICE CLEARANCE REQUIREMENTS.............................. 12

Service Clearance Requirements........................................................... 12

Operating Clearance Requirements...................................................... 12

WORKSTATION DIMENSIONS........................................................................ 13

Configuration with 2x20 Operator Display, 80key keyboard, 1-Line

Numeric Customer Display, Peripheral Tray, and 2182 Cash Drawer13

Configuration with Mono/Passive Color LCD Operator Display, 80key

keyboard, International VFD Customer Display with Telescope Mount,

Peripheral Tray, and 2182 Cash Drawer .............................................. 14

Configuration with TFT Color LCD Operator Display, 80key keyboard,

International VFD Customer Display with Telescope Mount,

Peripheral Tray, and 2182 Cash Drawer .............................................. 15

Configuration with 9” CRT Operator Display, 80key keyboard,

vi Site Preparation

Peripheral Tray, and 2182 Cash Drawer .............................................. 16

Configuration with 2 x 20 Operator Display, 80-Key Keyboard and 1-

Line Numeric Customer Display........................................................... 17

Configuration with 2 x 20 Operator Display, 176-Key Micromotion

Keyboard and International VFD Customer Display with Telescope

Mount...................................................................................................... 18

Configuration with Mono/Passive Color LCD Operator Display, 80-Key

Keyboard and International VFD Customer Display with Telescope

Mount...................................................................................................... 19

Configuration with................................................................................. 20

TFT LCD Display, 80key keyboard, International VFD Customer

Display with Telescope Mount............................................................... 20

Configuration with LCD Operator Display, 176-Key Micromotion

Keyboard and International VFD Customer Display with Telescope

Mount...................................................................................................... 21

Configuration with................................................................................. 22

TFT Color LCD Display, 176-Key Micromotion keyboard and

International VFD Customer Display with Telescope Mount............. 22

COMPONENT DIMENSIONS........................................................................... 23

Base Unit with 2 x 20 Operator Display and 80-key Conventional

Keyboard................................................................................................. 23

Base Unit with 10.4” Mono/Passive Color LCD Operator Display with

176-Key Micromotion Keyboard............................................................ 24

Base Unit with TFT Color Operator LCD Display and 176-Key

Micromotion keyboard ........................................................................... 25

Base Unit with 9” CRT Operator Display and 80-key Conventional

Keyboard................................................................................................. 26

Cash Drawer........................................................................................... 28

Customer Displays ................................................................................. 30

Printers ................................................................................................... 32

COMPONENT WEIGHTS ................................................................................ 35

POWER REQUIREMENTS............................................................................... 37

CABLE ROUTING CONSIDERATIONS

CABLE ROUTING CONSIDERATIONSCABLE ROUTING CONSIDERATIONS

CABLE ROUTING CONSIDERATIONS................................

................................................................

...................................................

......................................

...................38

3838

USABLE CABLE LENGTHS............................................................................ 38

SYSTEM CABLES

SYSTEM CABLESSYSTEM CABLES

SYSTEM CABLES ................................

................................................................

.....................................................

..........................................

.....................39

3939

Site Preparation vii

CABLE ILLUSTRATIONS................................................................................ 41

ENVIRONMENTAL REQUIREMENTS

ENVIRONMENTAL REQUIREMENTSENVIRONMENTAL REQUIREMENTS

ENVIRONMENTAL REQUIREMENTS................................

................................................................

....................................................

........................................

....................44

4444

BAROMETRIC PRESSURE.............................................................................. 44

TEMPERATURE............................................................................................. 44

HUMIDITY .................................................................................................... 44

APPENDIX A: TRANSIENT PROTECTION

APPENDIX A: TRANSIENT PROTECTIONAPPENDIX A: TRANSIENT PROTECTION

APPENDIXA: TRANSIENT PROTECTION................................

................................................................

...............................................

..............................

...............1

AC POWER LINE TRANSIENT PROTECTION ................................................... 1

DATA LINE TRANSIENT PROTECTION............................................................. 3

viii Site Preparation

Revision Record

Issue Date Remarks

A August 2000 First Issue

B December 2000 Update for Release 1.1

C March 2001 Update for Release 1.2

D December 2001 Update for Release 1.3

Andere Handbücher für 7448 Workstation

Inhaltsverzeichnis

Andere NCR Kasse Handbücher

NCR

NCR 7454 Bedienungsanleitung

Beliebte Kasse Handbücher anderer Marken

Royal

Royal 480nt Bedienungsanleitung

Olivetti

Olivetti ECR 8200 S Bedienungsanleitung

TEC

TEC TEC FS-3600 Bedienungsanleitung

Integrated System Laboratory

Integrated System Laboratory ISL 4006 Bedienungsanleitung

Sam4s

Sam4s ER-380 Fehlerbehebungshandbuch

Sharp

Sharp XE-A206 Stücklistenhandbuch

Samsung

Samsung ER 5215 Bedienungsanleitung

Toast

Toast Toast Bedienungsanleitung

Sharp

Sharp XE-A130 Kurzanleitung

TEC

TEC MA-600-1 series Bedienungsanleitung

QUORION

QUORION CR 1200 Bedienungsanleitung

Olivetti

Olivetti ECR 7700 LD eco Plus Bedienungsanleitung

Sharp

Sharp XE-A137-WH Operation Kurzanleitung

Sharp

Sharp XE-A203 - Cash Register Thermal Printing Graphic Logo... Bedienungsanleitung

TEC

TEC TEC MA-1060 Bedienungsanleitung

Casio

Casio PCR-408 Montageanleitung

ELCOM

ELCOM Euro-2100TE Bedienungsanleitung

American Changer

American Changer CLASSIC Series Bedienungsanleitung