NCR P1535 Bedienungsanleitung

USER GUIDE

NCR P1535 POS ( 7761 )

Release 1.1

BCC5-0000-5054

Issue C

The product described in this document is a licensed product of NCR Corporation.

NCR is a registered trademark of NCR Corporation. Product names mentioned in this publication may be trademarks or

registered trademarks of their respective companies and are hereby acknowledged.

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks

of HDMI Licensing LLC in the United States and other countries.

Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the terms

and conditions of an agreement you have with NCR, NCR's copyright notice must be included.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become

available. NCR, therefore, reserves the right to change specifications without prior notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,

photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR

office for information that is applicable and current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value of this book.

Please use the link below to send your comments.

EMail: FD230036@ncr.com

By NCR Corporation

Duluth, GA U.S.A.

Preface

Audience

This publication is written for hardware installer/service personnel, system integrators,

and field engineers.

Notice:This document is NCR proprietary information and is not to be disclosed or

reproduced without consent.

Safety Requirements

The NCR P1535 POS conforms to all applicable legal requirements. To view the

compliance statements see the NCR HSR POS Terminals Safety and Regulatory Statements

(BCC5–0000–5069).

Caution: The on/off switch is a logic switch only. The AC line voltage primaries are

live at all times when the power cord is connected. Therefore, disconnect the AC power

cord before opening the unit to install features or service this terminal.

Caution: UVLight — Avoid looking directly at UVLights.

Lithium Battery Warning

Warning: Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type as recommended by the manufacturer. Discard used

batteries according to the manufacturer's instructions.

Attention:Il y a danger d'explosion s'il y a remplacement incorrect de la batterie.

Remplacer uniquement avec une batterie du même type ou d'un type recommandé

par le constructeur. Mettre au rébut les batteries usagées conformément aux

instructions du fabricant.

Battery Disposal (Switzerland)

Refer to Annex 4.10 of SR814.013 for battery disposal.

IT Power System

This product is suitable for connection to an IT power system with a phase-to-phase

voltage not exceeding 240 V.

Peripheral Usage

This terminal should only be used with peripheral devices that are certified by the

appropriate safety agency for the country of installation (UL, CSA, TUV, VDE) or those

which are recommended by NCR Corporation.

Warning: DO NOT connect or disconnect the transaction printer while the terminal

is connected to AC power. This can result in system or printer damage.

Warning: DO NOT connect or disconnect any serial peripherals while the terminal

is connected to AC power. This can result in system or printer damage.

Grounding Instructions

In the event of a malfunction or breakdown, grounding provides a path of least

resistance for electric current to reduce the risk of electric shock. This product is

equipped with an electric cord having an equipment-grounding conductor and a

grounding plug. The plug must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local codes and ordinances. Do not

modify the plug provided – if it will not fit the outlet, have the proper outlet installed by

a qualified electrician. Improper connection of the equipment-grounding conductor can

result in a risk of electric shock.

The conductor with insulation having an outer surface that is green with or without

yellow stripes is the equipment-grounding conductor.

If repair or replacement of the electric cord or plug is necessary, do not connect the

equipment-grounding conductor to a live terminal. Check with a qualified electrician or

service personnel if the grounding instructions are not completely understood, or if you

are in doubt as to whether the product is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole

receptacles that accept the product’s plug. Repair or replace damaged or worn cords

immediately.

iii

Out of Box Failure (OBF)

If you experience an out of box failure (OBF) during installation or staging related to a

missing, wrong or defective unit or item, simply provide NCR with a detailed

description of the issue and the item will be replaced free of charge. For assistance with

this process send an email to CustomerSat.Retail@ncr.com with the following details:

• NCR Sales Order # (Sales Order # are located on the box)

• Date of Product Installation

• Product Model #

• Unit Serial #

• NCR part # of defective/missing/wrong component

• Description of Failure (please be specific. For example: “display will not power on”)

• Customer/Requestor’s contact name, phone number and/or e-mail address

• Address to ship replacement part(s)

Transport the product n its original packaging to prevent impact damages.

If you do not have access to a computer, you may leave a voice message at: 1-800-528-

8658 (USA), or (International) +1-770-623-7400. When leaving a message, please provide a

phone number and/or an email address so NCR can contact you if additional details are

needed.

Note: Used equipment that experiences a failure does not qualify as an OBF and

should go through the NCR warranty process.

Warranty

Warranty terms vary by region and country.

All parts of this product that are subject to normal wear and tear are not included in the

warranty. In general, damages due to the following are not covered by the warranty.

• Improper or insufficient maintenance

• Improper use or unauthorized modifications of the product.

• Inadequate location or surroundings. Site installation must conform to guidelines

listed in the Site Preparation document and the NCR Workstation and Peripheral AC

Wiring Guide (BST0-2115-53).

For detailed warranty arrangements please consult your contract documents.

Returning Defective Hardware for Service

Use the following procedure to report/return defective hardware.

Call the NCR Customer Care Center at 1-800-262-7782 and have the following information

available when you place the call.

• Class/Model number of the defective equipment

• Serial Number of the defective equipment

• Equipment location in the store

• Description of the problem, including any system error codes, error condition, or

guidance to the area of failure.

The NCR Agent will provide you with a work order number, which serves as your

Return Material Authorization (RMA). Please provide the RMA on the outside of the

shipping box.

Note: A work order must be opened for each device that is shipped for repair.

References

•NCRP1535 POS(7761)Site PreparationGuide (BCC5-0000-5053)

•7761 Service Guide (BCC5-0000-5055)

•7761 Parts IdentificationManual (BCC5-0000-5056)

Table of Contents

Chapter 1: Product Overview

Introduction 1

Features and Benefits 2

Optional Features and Benefits 4

Mounting Configurations 5

Expansion Options 6

Customer Display Options 7

Right Side Features (Port A) 8

Left Side Features (Port B) 9

Specifications 10

Operator Controls 13

Power Switch 13

Bezel LED 13

Label Locations 14

Chapter 2: Hardware Installation

Installation Restrictions 15

Installation Notes 16

Cable Restraint 16

Footprint 16

Power 16

Moisture 16

Touch Screen Cleaning 16

Magnetic Strip Reader (MSR) Cleaning 17

Biometric Cleaning 17

Hardware Platform Drivers 17

Ergonomic Workplace 18

Installing the Terminal 19

Connecting AC Power 23

Disconnecting the Power Cable 23

Connecting to a Network 23

Starting Up the P1535 Terminal 23

Installing a Transaction Printer 24

Installing a Cash Drawer 25

Second Cash Drawer Cable Connection 26

Using ExternalConnectors 27

RJ12 Serial Port 28

RJ45 Serial Port 29

LAN 30

USB 3.0Compliant Ports 31

Cash Drawer (CD) Port 32

Installing the Power Supply 33

Removing Top Assembly 38

Terminal with Expansion 39

Appendix A: Product IDs

P1535 POS(7761) 1

vii

Revision Record

Issue Date Remarks

AFeb 2016 First Issue

BJuly 2016 • Updated for Release 1.1

• Removed reference to VESAMount

CMay 2017 Added the following updates

• Quickserve 24V PUSB + 12V PUSB + Dual CD (24V) Expansion

• USBMSR with NCRKey

• Android OS

• 2x20 Double Byte Display

• Product IDs

Chapter 1: Product Overview

Introduction

The NCR P1535 is a Point-of-Sale (POS) terminal designed for the restaurant and food

service environment. The terminal utilizes a next generation Intel® Celeron™ Processor

N3160 (Quad core, 2.24 GHz). The highly efficient processor offers great performance,

but with lower power consumption for a more reliable design. The POS terminal comes

in a 15–inch display with a projected capacitive (PCap) touch screen.

Andere Handbücher für P1535

Inhaltsverzeichnis

Andere NCR Touch-Terminal Handbücher

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung

Prestel

Prestel VCS-G2PRO Bedienungsanleitung