NEC MultiSync XG-1352 Bedienungsanleitung

Before operating this projector, please read this manual carefully and completely.

This manual will provide you with the basic instructions for operation of the

projector. Installation, preliminary adjustments and procedures which require the

opening of the projector and contact with electrical components should be

performed by service personnel. For continued safe and reliable operation, use

only cables supplied by the manufacturer for power. Adhere to all notes and

warnings.

Features

©Multi scan circuit automatically locks on video, superdata from 15 to 85 kHz

(XG85) and graphics signals 15 to 135 kHz (XG135LC).

You can interface video and high resolution RGB signals from various

computers, workstations and graphics boards.

resolution of 250022000 (addressable) XG135LC and 160021200 (address-

able) XG85.

©Newly developed video output circuit makes possible 110 MHz of Video

Bandwidth (XG85) and 150MHz (XG135LC) with 1100 lumens peak light

output (XG85) and 1200 lumens (XG135LC).

©ECP lens produces an image with true color reproduction.

©AKB circuit provides stable white balance.

©Display size can be altered to accommodate any picture size from 60" to 300"

diagonal. In addition to ceiling mounting, floor, desk top and rear installations

are possible. (The ceiling mounting kits can be purchased as an optional item

for ceiling installation.)

©Digital convergence provides high accuracy for projecting fine graphic

displays.

©On-screen menus provide easy access to adjustment items.

©ISS-6020/ISS-6020G interface allows 100 inputs.

©Video system compatible with NTSC, PAL, SECAM and NTSC 4.43.

©Up to 100 sources can be stored in digital memory.

©Quick copy convergence for fast easy set up from one pre-set signal.

©Built in self diagnostics for on-sight troubleshooting.

©Built in test patterns such as “CROSS HAIR”, “CROSS HATCH”, “DOT”,

“WINDOW” ,“ALL WHITE”, “GRAY SCALE”, and “H (FOCUS)” for

accurate setup.

©Source information status display.

©The SEQUENCER function allows the projector to automatically select input

signals one after another as programmed by the user.

©Compatible with a component video signal such as DVD.

12345

123456

INTRODUCTION.

INTRODUCTION

Important Safeguards

The following are important safety instructions designed to ensure the long life

of your projector and to prevent fire and shock hazards. Be sure to read these

safety instructions carefully and follow all warnings given below.

Installation

The projector must be installed by trained personnel.

Place the projector on a flat, level surface and in a dry area free from dust and

moisture. Do not place the projector in direct sunlight, near stoves or other heat

radiating appliances. Smoke, steam and exposure to direct sunlight could ad-

versely affect the internal components. Avoid rough handling when moving your

equipment as a strong shock could damage its internal components. If installing

the projector on the ceiling, use only optional ceiling kits (two types) supplied by

the manufacturer. Observe all instructions and warnings. Since installing the

projector on the ceiling requires special techniques and a optional ceiling kit,

users must not try to install it. Contact your dealer for ceiling installation.When

ordering the ceiling kit, specify the part name, PG CMKIT-F or PG CMKIT.

Power supply

The XG-852 and XG-1352 projector are designed to operate on 120 V 60 Hz, and

the XG-852G and XG-1352G are designed to operate on 220-240 V 50 Hz AC

power supply. Make sure your local power supply matches these requirements

before operation.

Handle the power cord carefully and avoid excessive bending. A damaged cord

may cause electric shock or fire. If the projector is not to be used for an extended

period, remove the plug from the power outlet.

Cleaning

Unplug the projector from the power outlet before cleaning.

Clean the cabinet and front panel periodically with a soft cloth. If heavily stained,

use a mild detergent solution. Never use strong detergents or solvents such as

alcohol or thinner to clean your projector.

Lens cleaning: Avoid touching the lens surfaces.

Special coating is applied to the lens surfaces.

Consult your dealer for lens cleaning.

Fire and Shock Precautions

Adequate ventilation must be provided to prevent heat build-up inside the

projector. Make sure the ventilation holes are unobstructed.

Keep the inside of the projector free from foreign objects, such as paper clips,

nails, paper, etc. Do not attempt to retrieve such objects yourself or insert metal

objects such as wire and screw-drivers inside the projector. If a hazardous object

falls inside the projector, unplug it immediately and call a qualified electrical

repairman for removal.

Do not set liquids on top of the projector.

PART NAMES AND FUNCTIONS

Front Terminal Panel

Rear Control Panel

ACAT OUT R/Cr G/Y B/Cb H/HV V S-VIDEO VIDEO OPTION REMOTE1 REMOTE2

OUT IN

INPUT SELECT ENTERON/OFFINDICATOR

INPUT SELECT POWER

1 32

4 65 7

GFEDCB

123456

12345

123456

PART NAMES AND FUNCTIONS.

A cover is provided to attach the rear control panel.

12345

123456

EXAMPLES OF CONNECTIONS.

CAUTIONS ON CONNECTIONS:

• Unplug the projector and other equipment from the AC

supply before making connections.

• Make sure that the plug of the power cord is properly

connected to the power outlet. A loose connection may cause

hum or noise.

•Confirm your connection layout with the user’s manual

accompanying the equipment to be connected with the ISS-

6020/ISS-6020G Switcher.

NOTE: This projector does not have built-in speakers.

• Make sure that the STANDALONE mode is selected from the CONNECT CONDITION menu. Contact your dealer for the

information in detail.

When Used in Stand Alone Operation

Components with RGB and H/V SYNC

outputs such as a personal computer

External Control

VCR or Video disc player

ACAT OUT R/Cr G/Y B/Cb H/HV V S-VIDEO VIDEO OPTION REMOTE1 REMOTE2

OUT IN

INPUT SELECT ENTERON/OFFINDICATOR

INPUT SELECT POWER

VCR with S-Video outputs

DVD Player with a COMPONENT video

output

123456

12345

123456

INSTALLATION SET-UP INSTRUCTION.

Before Installation

The installation procedure is different according to the projection system and screen size. From the factory the projector is set for

ceiling mount, 100 inch diagonal screen size and a projection angle of 12.4 degrees (XG85)/12.2 degrees (XG135LC).

Installation and preliminary adjustments are required as shown on table below.

Adjustment

items

Screen size

(diagonal)

Projection type

None (

Set the focus ring when changing projection angle

)

Yes

None (

Set the focus ring when changing projection angle

)

Yes

None (S

et the focus ring when changing projection angle

)

Yes

None (

Set the focus ring when changing projection angle

)

Yes

None

Yes

100 inch

other than 100 inch

100 inch

other than 100 inch

100 inch

other than 100 inch

100 inch

other than 100 inch

Ceiling mounting Front projection

Desk top Front projection type

Ceiling mounting/Rear projection

Desk top Rear projection

None

Yes

None

Various

adjustments

NOTE: For XG85, the “100 inch” covers the range of screen size between 80 and 129 inches. For XG135LC, The ''100 inch'' covers

the range of screen size between 90 and 109 inches.

NOTE: Focus ring adjustment on pages 15 and 16 for XG85, and 17 and 18 for XG135LC.

H Polarity

change

Focus ring and CRT angle change

Carrying the Projector

WARNING:

Be sure to use the handles when carrying the projector.

Pulling Out the Handle

Pull out the handle from the bottom side.

Retracting the Handle

Press down the two levers at the same time to retract the

handle.

Ceiling Mount Projection Distance and Screen Size for XG85

•

Install in such a way that the projector and screen are positioned in the proper direction and at the proper angle. If not, the projector's

performance will be affected and its reliability will decrease. Be sure to position the projector properly.

The manufacturer will not be held responsible for any problems occurring when the projector is not installed in the proper position.

The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of

installation

NOTE:

• For screens 150 inches (3810mm) or larger (in the diagonal direction), set so that the distance between the surface of

installation of the mounting A and the ceiling is E.

• Set the projection distance based on the width of the screen.

• If the figures on the table do not match the figures in the formulae, use the figures on the table.

• For screen sizes of 60 to 300 inches not indicated on the table, use the following proportional formulae:

When using a screen 150"

(3810mm) or larger (in the

diagonal direction)

Screen center

Ceiling Mounting

Line of sight

αA

Screen center

CCeiling Mounting

11.15"

(283mm)

5.12"

(130mm)

Ceiling Mount System

144"

(180") 160"

(200") 192"

(240") 216"

(270") 240"

(300")

48"

(60")

Screen size H-Width

(4:3 Diagonal)

56"

(70")

0.9760.9770.978

γ (=cosα)

12.7°12.6°12.4°12.1°

0.2200.2180.2150.210

β (=sinα)

196.11

4981

54.38

1381

191.31

4860

–

214.02

5436

58.31

1481

208.78

5303

1.69

258.51

6566

68.10

1730

252.18

6406

3.91

100

290.48

7378

75.12

1908

283.37

7198

5.88

150

315.67

8018

80.66

2049

307.95

7822

9.35

238

81.54

2071

28.36

721

79.73

2025

–

inch

70.28

1785

26.00

661

68.72

1746

–

Units=mm W"=Screen H-Width

A = (25/962W"112.5)2126.64`1785

B = (β2A)`286

C = γ2A

E = (1/22Screen Height)1B

Units=inches W"=Screen H-Width

A = (25/962W"112.5)24.99`70.28

B = (β2A)`11.26

C = γ2A

E = (1/22Screen Height)1B

• The margin of error for projection distance (A) is53%.

INSTALLATION SET-UP INSTRUCTION

120"

(150")

164.69

4183

47.19

1199

160.72

4083

–

96"

(120")

133.43

3389

39.91

1014

130.32

3310

–

80"

(100")

112.68

2862

35.46

901

110.05

2796

–

72"

(90")

101.74

2584

33.11

841

99.36

2524

–

64"

(80")

91.6

2318

30.86

784

89.13

2264

–

INSTALLATION SET-UP INSTRUCTION

Ceiling Mount Projection Distance and Screen Size or XG135LC

•

Install in such a way that the projector and screen are positioned in the proper direction and at the proper angle. If not, the projector's

performance will be affected and its reliability will decrease. Be sure to position the projector properly.

The manufacturer will not be held responsible for any problems occurring when the projector is not installed in the proper position.

The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of

installation

NOTE:

• For screens 150 inches (3810mm) or larger (in the diagonal direction), set so that the distance between the surface of

installation of the mounting A and the ceiling is E.

• Set the projection distance based on the width of the screen.

• If the figures on the table do not match the figures in the formulae, use the figures on the table.

• For screen sizes of 60 to 300 inches not indicated on the table, use the following proportional formulae:

When using a screen 150"

(3810mm) or larger (in the

diagonal direction)

Screen center

Ceiling Mounting

Line of sight

αA

Screen center

CCeiling Mounting

11.15"

(283mm)

5.12"

(130mm)

Ceiling Mount System

144"

(180") 160"

(200") 192"

(240") 216"

(270") 240"

(300")

48"

(60")

Screen size H-Width

(4:3 Diagonal)

56"

(70") 64"

(80")

0.9760.9770.979

γ (=cosα)

12.6°12.2°11.8°

0.2180.2110.204

β (=sinα)

209.57

5323

56.55

1436

204.54

5195

–

232.48

5905

61.55

1563

226.90

5763

–

278.15

7065

71.51

1816

271.47

6895

0.47

82.83

2104

27.78

705

81.10

2060

–

94.61

2403

30.18

767

92.62

2353

–

inch

71.10

1806

25.38

645

69.61

1768

–

Units=mm W"=Screen H-Width

A = (25/962W"112.5)2141`1825

B = (β2A)`275

C = γ2A

E = (1/22Screen Height)1B

Units=inches W"=Screen H-Width

A = (25/962W"112.5)25.47`71.85

B = (β2A)`10.83

C = γ2A

E = (1/22Screen Height)1B

• The margin of error for projection distance (A) is53%.

309.17

7853

78.28

1988

301.75

7665

2.72

338.62

8601

84.70

2151

330.50

8395

5.28

134

120"

(150")

12.4°

0.215

175.16

4449

48.45

1231

171.13

4347

–

80"

(100")

118.07

2999

35.79

909

115.36

2930

–

72"

(90")

106.34

2701

33.31

846

103.89

2639

–

96"

(120")

140.91

3579

40.61

1032

137.66

3497

–

123456

12345

123456

PROJECTION CONFIGURATION CHANGE.

Before Installation Change

The projector is electrically and mechanically set for 100 inch diagonal screen, front throw ceiling mount and a projection angle of

12.4˚ (XG85)/12.2˚(XG135LC). If your application is different from the factory setting(for example, ceiling to floor and screen

size between 60 and 300 inch), you will have to reconfigure the projector for your application. Follow the change procedures

according to the instructions below.

1) Set the focus ring to the proper position. (See pages15 and 16.)

For 100" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

2) Adjust the angle of the CRT's. (See page 16.)

For 100" screen size

Move the CRT to the 100 position

To change to the desk top system (front)

1) Reverse the scan. (See page 14.)

3) Adjust the angle of the CRT's. (See page 16.)

For 100" screen size

Move the CRT to the 100 position

4) Select an installation from the PJ ORIENTATION menu in

the SETTING menu. (See “Projection Type Selection” in the

setup manual.)

2) Set the focus ring to the proper position. (See pages 15 and 16.)

For 100" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

For 120" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

For 180" screen size

R – A-5, B-5

G – A-1, B-5

B – A-5, B-5

For 120–180" screen size and the

other screen sizes

Move the CRT to the 120, 180, or

60–300 position

For 120" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

For 180" screen size

R – A-5, B-5

G – A-1, B-5

B – A-5, B-5

For 120–180" screen size and the

other screen sizes

Move the CRT to the 120, 180, or

60–300 position

4) Select an installation from the PJ ORIENTATION menu in

the SETTING menu. (See “Projection Type Selection” in the

setup manual.)

To change to the ceiling mount system (rear)

1) Reverse the scan. (See page 14.)

2) Set the focus ring to the proper position. (See pages 16 and 17.)

For 100" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

3) Adjust the angle of the CRT's. (See page 17.)

For 100" screen size

Move the CRT to the 100 position

For 120" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

For 180" screen size

R – A-5, B-5

G – A-1, B-5

B – A-5, B-5

For 120–180" screen size and the

other screen sizes

Move the CRT to the 120, 180, or

60–300 position

To change to the desk top system (rear, 0 projection angle)

For 100" screen size

Move the CRT to the 100 position

For 120–180" screen size and the

other screen sizes

Move the CRT to the 120, 180, or

60–300 position

1) Set the focus ring to the proper position. (See pages 16 and 17.)

For 100" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

For 120" screen size

R – A-3, B-3

G – A-1, B-3

B – A-3, B-3

For 180" screen size

R – A-5, B-5

G – A-1, B-5

B – A-5, B-5

2) Adjust the angle of the CRT's (See page 17.)

3) Select an installation from the PJ ORIENTATION menu in

the SETTING menu. (See “Projection Type Selection” in the

setup manual.)

To change screen size only:

For XG85

123456

12345

123456

BEFORE SET-UP.

Displaying the Menu and Adjustment Screens

Access of all set-up functions is done through the menu system.

Depending upon button selection, your desired screen will be displayed as shown below:

ADJUST menu

NOTE: Some function items will not be used depending on the input video signal or connected peripheral equipment.

ADJUST

ADJUST menu

– ADJUST –

1 / SIGNAL ENTRY

2 / FOCUS

3 / ALIGNMENT

4 / CONVERGENCE

5 / KELVIN

6 / R,G,B GAIN

7 / PASSCODE

8 / OPTION

9 / REF. ADJUST

SIGNAL ENTRY screen

FOCUS menu

– FOCUS –

1 / CENTER

2 / EDGE ALL

3 / EDGE SEPA.

4 / CORNER

ALIGNMENT menu

– ALIGNMENT –

01 / TILT, SKEW

02 / BOW

03 / AMPLITUDE

04 / LINEARITY

05 / KEY-STONE

06 / PIN-CUSHION

07 / LINEAR-BAL.

08 / KEY-BALANCE

09 / PIN-BALANCE

10 / LINE DIST.

11 / R,G,B POINT



CONVERGENCE menu

– CONVERGENCE –

1 / TILT, SKEW

2 / BOW

3 / AMPLITUDE

4 / LINEARITY

5 / KEY-STONE

6 / PIN-CUSHION

7 / LINEAR-BAL

8 / LINE DIST.

9 / POINT

10/ PHASE



1 / COLOR TEMP.

2 / WHITE BAL.

Adjustment screen

PASSCODE menu

OPTION menu

– OPTION –

1 / SETTING MODE

2 / MENU MODE

3 / SEQUENCER

4 / PJ ADDRESS

5 / VERSION

6 / HOUR METER

7 / DEFAULT DATA

Adjustment screen

FOCUS

CTL G

Sub menu and

Adjustment screen

CTL R,B

TILT

BOW

AMPLIT

LINEAR

KEYSTN

PINCUS

CTL LINEAR

CTL KEYSTN

CTL PINCUS

TILT

BOW

AMPLIT

LINEAR

KEYSTN

PINCUS

PHASE

CTL LINEAR

NEW PASSCODE?

input screen

PASSCODE

DISABLE? menu

Sub menu

/ Setting screen

KELVIN

– REF. ADJUST –

1 / ASTIG

2 / BRIGHT UNIFORM.

3 / WHITE UNIFORM.

4 / RASTER CENTERING

CTL BOW

POINT

CTL BOW

POINT

– KELVIN –

Sub menu and

Adjustment screen

CTL ADJUST

12345

123456

SIGNAL ENTRY.

To make the signal entry, proceed as follows:

1Press the ADJUST button.

• The “ADJUST” menu is displayed.

NOTE: The projector may ask you to enter your passcode. See

61 for the explanation of the PASSCODE.

2Use the CURSOR or button to highlight the “1/SIGNAL

ENTRY” line and press ENTER.

• The “SIGNAL ENTRY” list will be displayed.

• You can also select the “SIGNAL ENTRY” list directly by

pressing the INPUT “1” button.

3Use the CURSOR or button to select the desired line and

press ENTER.

• The Signal entry menu will be displayed.

NOTE: To advance to the next page or to the previous page,

hold down the CTL button then press the

CURSOR or button. To directly access a page, hold down

the CTL button then press any one of the INPUT buttons.

On Signal Entry

The projector uses a micro-processor to automatically read and distinguish between all video signals input at the same time. These

signals are then used to make optimum adjustments for focus, convergence, alignment, etc. Various parameters must be registered

into the micro-processor beforehand to ensure the video signals are recognized and adjusted to optimum quality.

The Signal Entry registers these video signals in the SIGNAL ENTRY list and at the same time obtains the various parameters

pertaining to these signals. Always access this mode first whenever inputting video signals for the first time so that you can register

the video signals before making any adjustments. If the current input signal(s) has not been registered, the “UNREGISTERED

SIGNAL” message is displayed on screen.

NOTE: If you have software which changes scanning mode due to the graphic board of your PC (such as VGA), it will be necessary

to register signal entry for each scanning mode. This can be done using your PC by way of stopping the software in each scanning

mode and performing a signal entry operation.

Signal Entry Procedures

– ADJUST –

1 / SIGNAL ENTRY

2 / FOCUS

3 / ALIGNMENT

4 / CONVERGENCE

5 / KELVIN

6 / R,G,B GAIN

7 / PASSCODE

8 / OPTION

9 / REF.ADJUST

P01/10–2 SIGNAL ENTRY

STANDALONE

15.74kHz

48.60kHz

60.00Hz

50.00Hz

60.00Hz

DATE

00/00/00

P01/10–1 SIGNAL ENTRY

STANDALONE

SOURCE

VIDEO

RGB

INPUT

NAME

NTSC3.58

NTSC4.43

PAL

SECAM

VESA1024

§ ©

Signal name Input terminal Entry dateRgistered input module

Connect condition of the Switcher

Vertical

Frequency

Horizontal

Frequency

Page / total pages – sheet No.

OUTPUT DATA : LIST NO.✻✻ OUTPUT DATA : LIST NO.✻✻

Output data for the signal currently projected.

Andere Handbücher für MultiSync XG-1352

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Projektor Handbücher

NEC

NEC PX750U Series Bedienungsanleitung

NEC

NEC P547UL Bedienungsanleitung

NEC

NEC MT1065 - MultiSync XGA LCD Projector Bedienungsanleitung

NEC

NEC NP-UM330X Series Bedienungsanleitung

NEC

NEC PV800UL-W Betriebsanleitung

NEC

NEC NP61 Series Bedienungsanleitung

NEC

NEC VE281 Bedienungsanleitung

NEC

NEC NP3150 Series Bedienungsanleitung

NEC

NEC P350W Series Bedienungsanleitung

NEC

NEC PA1004UL Series Bedienungsanleitung

NEC

NEC LT100 - MultiSync XGA DLP Projector Installations- und Benutzerhandbuch

NEC

NEC LT170 Bedienungsanleitung

NEC

NEC NC1201L-A Bedienungsanleitung

NEC

NEC PE401H Bedienungsanleitung

NEC

NEC PX2201UL Bedienungsanleitung

NEC

NEC PA1004UL-W Bedienungsanleitung

NEC

NEC NP610S Series Installationsanleitung

NEC

NEC LT75Z - MultiSync SVGA DLP Projector Montageanleitung

NEC

NEC MultiSync MT1040 Bedienungsanleitung

NEC

NEC V230X Bedienungsanleitung

NEC

NEC VT46 Montageanleitung

NEC

NEC NC800C Bedienungsanleitung

NEC

NEC NP901W Handbuch

NEC

NEC NP1000 Handbuch

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung