NEC VT695 Gebrauchs- und Wartungshandbuch

======================================================================

Control Commands for NEC Projector (Basic) Rev 3.0.30f

----------------------------------------------------------------------

Updated on November 09, 2007

----------------------------------------------------------------------

This file contains information about NEC projector control commands.

Model

Name

GT60 : GT5000/GT6000 Series

HT : HT1000/HT1100 Series

HT10 : HT410/HT510 Series

LT : LT180

LT30 : LT25/LT30/LT35 Series

NP40 : NP40/NP50/NP60 Series

LT60 : LT220/LT240/LT240K/LT260/LT260K/LT245/LT265 Series

LT80 : LT280/LT380 Series

MT70 : MT860/MT1060/MT1065/MT1075 Series

NP1000 : NP1000/NP2000/NP1150/NP2150/NP3150 Series

WT : WT600/WT610/WT615 Series

VT : VT770 Series

VT70 : VT37/VT47/VT480/VT57/VT570/VT575/VT670/VT676 Series

VT80 : VT48/VT480/VT580 Series

VT90 : VT49/VT490/VT590/VT595/VT695/VT700 Series

NP4000 : NP4000/NP4001 Series

======================================================================

Contents

1. Projector Control

2. Connection Method

3. Interface Conditions

4. List of Commands

5. Command Descriptions

6. Table of Response Error Codes

======================================================================

1. Projector Control

----------------------------------------------------------------------

NEC projectors make use of control commands that control the functions of the projector via connection with

a personal computer or another device.

======================================================================

2. Connection Method

----------------------------------------------------------------------

The following 3 kinds of connection methods are available for sending and receiving control commands.

1. Serial connection using the serial port on the projector

A serial cable is required.

2. USB connection using the USB port on the projector

A USB cable is required.

3. LAN connection

3-1. LAN connection using a wired LAN card

A wired LAN card and LAN cable are required.

3-2. LAN connection using a wireless LAN card

A wireless LAN card is required.

3-3.LAN connection using the LAN port on the projector

A LAN cable is required.

Status of supported connection

(1) (2) (3-1) (3-2) (3-3)

Serial

Port USB

Port Wired

LAN

Card

Wireless

LAN

Card

Wired

LAN

Port

GT5000/6000 Yes Yes Yes Yes Yes

HT410/510 Yes No No No No

HT1000/1100 Yes No No No No

LT180 Yes No No No No

LT25/30/35 Yes No No No No

LT220/240/260 Yes No Yes Yes No

LT240K/260K Yes Yes Yes Yes No

LT245/265/280/380 Yes No No Yes Yes

MT860/1060/1065/1075 Yes Yes Yes Yes No

NP40/50/60 Yes No No No No

NP1000/2000/1150/2150/3150 Yes No No Yes Yes

NP4000/4001 Yes No No No No

VT770 Yes No No No No

VT37/47/470/57/570/575/670/676 Yes No No No No

VT48/480/580 Yes No No No No

VT49/490/590/595/695/VT700 Yes No No No No

WT600/610/615 Yes Yes Yes Yes No

Yes: Supported

No: Not Supported

* A USB cable is supplied as standard with the MT860/1060/1065/1075.

* The GT5000/6000 does not come with a USB cable.

* Note that a connection method using the supplied USB cable is not supported for the LT220/240/260.

* The serial cable, LAN card and LAN cable are separately sold.

* The WT610 replaced the WT610 and uses the same command set.

(CAUTION)

Before making connections, be sure to invalidate the standby mode of the projector and set the "idle mode".

The projector cannot use the control commands in the standby mode.

Setting method: Under projector [Projector Options] --> [Setup], enter a check for [Idle Mode] on Page 4.

====================================================================

3. Interface Conditions

----------------------------------------------------------------------

Serial connection

----------------------------------------------------------------------

The communications method conforms to the RS-232C standard.

Baud rate: 38400 bps (VT70/VT80/VT90 series: 19200bps)

Data length: 8 bits

Parity bit: No parity

Stop bits: 1 bit

Communications mode: Full duplex

The control connector is described below.

[ HT/LT/NP40/VT70/VT80/VT90/WT ]

The PC CONTROL connector is a mini DIN 8-pin connector.

1 To TxD of PC

4 To GND of PC

7 To RxD of PC

* 2, 3, 5, 6, and 8 are used inside the projector.

[ GT/LT80/MT/NP1000/VT (except VT70/VT80/VT90) ]

The PC CONTROL connector is a D-SUB 9-pin connector.

2 To TxD of PC

3 To RxD of PC

5 To GND of PC

7 To CTS of PC

8 To RTS of PC

USB connection

----------------------------------------------------------------------

This conforms to the USB1.1 standard.

Transfer speed: All speeds (supported)

Endpoint: Control transfer Endpoint 0

Device class: HID class (Ver1.1)

USB1.1 Standard: Universal Serial Bus Specification Revision 1.1

HID : Human Interface Device

Connector Specifications

1 VBUS (Power supply)

2 D- (- Signal)

3 D+ (+ Signal)

4 GND (Ground)

* Depending on the USB host controller in the personal computer, the USB connection may fail to operate.

When using a USB hub, please use a self-powered type, not a bus-powered type. When using a USB hub,

connection to the first stage of the USB hub is recommended.

LAN connection

----------------------------------------------------------------------

[ Wired LAN port ]

LAN interface

Communication speed: Auto setting (10/100Mbps)

Certified standard: IEEE802.3 (10BASE-T)

IEEE802.3u (100BASE-TX, Auto-Negotiation)

A LAN connector (8 male RJ-45 connector)

1 TD+ Transmit data (+)

2 TD- Transmit data (-)

3 RD+ Receive data (+)

4 Not used

5 Not used

6 RD- Receive data (-)

7 Not used

8 Not used

[ Wired/wireless LAN card ]

The LAN connections will differ depending on the commercial LAN card that is used.

- For information on supported LAN cards, visit:

Global: http://www.nec-pj.com/

[Port Number]

The TCP port number used is "7142".

====================================================================

4. List of Commands

----------------------------------------------------------------------

* Example for command

----------------------------------------------------------------------

Command name Example

----------------------------------------------------------------------

006. RUNNING SENSE 00H 81H 00H 00H 00H 81H

007. COMMON DATA REQUEST 00H C0H 00H 00H 00H C0H

009. ERROR STATUS REQUEST 00H 88H 00H 00H 00H 88H

015. POWER ON 02H 00H 00H 00H 00H 02H

016. POWER OFF 02H 01H 00H 00H 00H 03H

018. INPUT SW CHANGE 02H 03H 00H 00H 02H <DATA> CKS

020. PICTURE MUTE ON 02H 10H 00H 00H 00H 12H

021. PICTURE MUTE OFF 02H 11H 00H 00H 00H 13H

022. SOUND MUTE ON 02H 12H 00H 00H 00H 14H

023. SOUND MUTE OFF 02H 13H 00H 00H 00H 15H

024. ONSCREEN MUTE ON 02H 14H 00H 00H 00H 16H

025. ONSCREEN MUTE OFF 02H 15H 00H 00H 00H 17H

030. GAIN ADJUST 03H 10H 00H 00H 05H <DATA> CKS

030-2. VOLUME ADJUST 03H 10H 00H 00H 05H 05H <DATA> CKS

030-12. IMAGE MODE ADJUST 03H 10H 00H 00H 05H <DATA> CKS

037. INFORMATION REQUEST 03H 8AH 00H 00H 00H 8DH

037-1. LAMP INFORMATION REQUEST 03H 8CH 00H 00H 00H 8FH

037-2. LAMP INFORMATION REQUEST 2 03H 94H 00H 00H 00H 97H

037-4. LAMP INFORMATION REQUEST 3 03H 96H 00H 00H 02H <DATA> CKS

050. REMOTE KEY CODE 02H 0FH 00H 00H 02H 00H 00H 13H

060. GAIN PARAMETER REQUEST 2 03H 04H 00H 00H 03H <DATA> CKS

077. MUTE CONTROL 02H 1AH 00H 00H 02H <DATA> CKS

078-1. SETTING REQUEST 00H 85H 00H 00H 01H 00H CKS

078-2. RUNNING STATUS REQUEST 00H 85H 00H 00H 01H 01H CKS

078-3. INPUT STATUS REQUEST 00H 85H 00H 00H 01H 02H CKS

078-4. MUTE STATUS REQUEST 00H 85H 00H 00H 01H 03H CKS

078-5. MODEL NAME REQUEST 00H 85H 00H 00H 01H 04H CKS

078-6. MIRROR COVER STATUS REQUEST 00H 85H 00H 00H 01H 05H CKS

079. FREEZE CONROL 01H 98H 00H 00H 01H DATA01 CKS

110. AUTO FUNCTIONS EXECUTE 03H B6H 00H 00H 01H <DATA> CKS

305-1. BASE MODEL TYPE REQUEST 00H BFH 00H 00H 01H <DATA> CKS

305-3. PROJECTOR INFORMATION REQUEST 00H BFH 00H 00H 01H <DATA> CKS

* Availability by Model

----------------------------------------------------------------------

Model No.

-------------------------

01 : LT240/LT260

02 : MT1060/MT1065/MT1075

03 : HT1000

04 : LT220

05 : MT860

06 : WT600/WT610/WT615

07 : GT5000

08 : LT240K/LT260K

09 : GT6000

10 : HT1100

11 : VT770

12: HT410/HT510 (HT10 Series)

13 : LT245/LT265

14 : LT280/LT380

15 : LT180

16 : VT37/VT47/VT470/VT57/VT570/VT575/VT670/VT676 (VT70 series)

17 : VT48/VT480/VT580 (VT80 Series)

18 : NP1000/NP2000/NP1150/NP2150/NP3150 (NP1000/1050 Series)

19 : LT25/LT30/LT35 (LT30 Series)

20 : NP40/NP50/NP60 (NP40 Series)

21 : VT49/VT490/VT590/VT595/VT695/VT700 (VT90 Series)

22: NP4000/NP4001 (NP4000 Series)

Meaning of Symbols

--------------------------------------------------------------------

* Supported

! Is available depending on model's version

- Not Supported

CommandName 12345678910111213141516171819202122

006.RUNNINGSENSE ***********-**---*---*

007.COMMONDATAREQUEST ***********-**---*---*

009.ERRORSTATUSREQUEST **************---*****

015.POWERON **********************

016.POWEROFF **********************

018.INPUTSWCHANGE **********************

020.PICTUREMUTEON **********************

021.PICTUREMUTEOFF **********************

022. SOUND MUTE ON * * *****************-**

023. SOUND MUTE OFF * * *****************-**

024.ONSCREENMUTEON **********************

025.ONSCREENMUTEOFF **************---***-*

030.GAINADJUST ***********-***--*----

030-2. VOLUME ADJUST

Volume ***********-**--***-**

Bass -*--*-*-*-*--*---*----

Treble -*--*-*-*-*--*---*----

Balance -------------*---*----

030-12. IMAGE MODE ADJUST

AspectRatioInputSignal ***********-**---*---*

037.INFORMATIONREQUEST **************---*****

037-1.LAMPINFORMATIONREQUEST **********************

037-2.LAMPINFORMATIONREQUEST2***********-**---*---*

037-4.LAMPINFORMATIONREQUEST3!!!!!!*****-**---*-***

050.REMOTEKEYCODE **************---*****

060.GAINPARAMETERREQUEST2 ***********-**---*---*

077.MUTECONTROL **********************

078-1.SETTINGREQUEST ***********-**---*---*

078-2. RUNNING STATUS REQUEST * * *********-**---*---*

078-3.INPUTSTATUSREQUEST ***********-**---*---*

078-4.MUTESTATUSREQUEST ***********-**---*---*

078-5.MODELNAMEREQUEST ***********-**---*---*

078-6.MIRRORCOVERSTATUSREQUES-----*----------------

079.FREEZECONTROL ***********-*-------*-

110. AUTO FUNCTIONS EXECUTE - -----------------!*--

305.1BASEMODELTYPEREQUEST -----------*--*-*-****

305.3 PROJECTOR INFORMATION REQU

-----------*--*-*-****

Availability by Model

======================================================================

5. Command Descriptions

----------------------------------------------------------------------

Precautions with Inscriptions:

(*1) Projector ID

It is the value when forwarding a factory.

This reflects the "Projector ID" that has been set to the projector.

(*2) Model code: "xxH" inscription

This will differ depending on the projector.

In case of MT/NP1000/1050 series 10H

In case of LT/LT80 series 20H

In case of VT series 40H

In case of GT series 50H

In case of HT series 60H

In case of WT series 70H

In case of HT10 series D0H

In case of LT180 series D0H

In case of LT30 series D0H

In case of NP40 series D0H

In case of NP4000 series 80H

(*3) Checksum: "CKS" inscription

This is the value of the lower 8 bits of the results calculated in byte units from all of the data up to the

immediately preceding data.

Example:

20H 81H 01H 60H 01H 00H 03H

+ + + + + + = CKS

(*4) Response error number

This is the value of the error number at the time of an error.

See "NAK" of "6-2. Data portion of response".

(*5) Term “RGB” and “COMPUTER”

On the HT1100, VT770, LT245/ LT265/ LT280/ LT380,

NP1000/NP2000/NP1150/NP2150/NP3150/NP4000/NP4001, LT25/ LT30/ LT35, VT48/ VT480/ VT580,

VT49/VT490/VT590/VT595/VT695/VT700 and NP40/NP50/NP60, the term "RGB connector" has been

changed to "COMPUTER".

(*6) Term “DVI” and “COMPUTER”

On the LT380, NP1000/NP2000/NP1150/NP2150/NP3150/NP4000/NP4001 and VT595/VT695/VT700, the

term "DVI connector" has been changed to "COMPUTER".

006. RUNNING SENSE

**********************************************************************

Function:

This command acquires the operation mode of the projector.

Command:

00H 81H 00H 00H 00H 81H

Response: At the time of a success

20H 81H 01H xxH 01H DATA01 CKS

(*1) (*2) (*3)

Data Portion Contents

-------------------------------------------------------------------

DATA01 Status of operation

Bit 7: Power On/Off processing

0 = No execution (Normal condition)

1 = During execution

Bit 6: Selecting signal processing

0 = No execution (Normal condition)

1 = During execution

Bit 5: Cooling processing

0 = No execution (Normal condition)

1 = During execution

Bit 4: External control mode

0 = OFF

1 = ON

Bit 3: Reserved

Bit 2: Reserved

Bit 1: Projector status

0 = Idling

1 = Power On

Bit 0: Reserved

Response: At the time of a failure

A0H 81H 01H xxH 02H DATA1H DATA02 CKS

(*1) (*2) (*4) (*3)

007. COMMON DATA REQUEST

**********************************************************************

Function:

This command acquires all of the detailed conditions of the projector.

Command:

00H C0H 00H 00H 00H C0H

Response: At the time of a success

20H C0H 01H xxH 80H DATA01 .. DATA128 CKS

(*1) (*2) (*3)

Data Portion Contents

-------------------------------------------------------------------

DATA01 Projector type

See DATA70..71

08H : NP4000 Projector

DATA02 Projector ID

1 .. 64

DATA03 Reserved

DATA04 Projector status

00H: Idling

01H: Power On

DATA05 Cooling processing

00H: No execution (Normal condition)

01H: During execution

DATA06 Indication signal number (Entry list number - 1)

0 .. 199

DATA07 Type 1 of input terminal to be selected (!)

01H : 1

02H : 2

03H : 3

04H : 4

05H : 5

DATA08 Type 2 of input terminal to be selected (!)

01H : RGB (*5)

02H : VIDEO

03H : S-VIDEO

04H : COMPONENT

05H : Reserved

06H : DIGITAL (*6)

07H : VIEWER

08H : SLOT1

09H : SLOT2

DATA09 Indication signal type

* Valid only when Type 2 of input terminal is 02H or 03H

x0H : NTSC3.58

x1H : NTSC4.43

x2H : PAL

x3H : PAL60

x4H : SECAM

x5H : B/W60

x6H : B/W50

x7H : PALNM

x8H : NTSC3.58 LBX

x9H : NTSC3.58 SQZ

xDH : NTSC

xEH : PAL-M

xFH : PAL-N

* x: undefined

DATA10 .. 12 Reserved ( undefined )

DATA13 .. 20 Horizontal frequency of the indication signal(string)

("000.00" kHz + NULL(0)+ NULL(0) )

DATA21 .. 28 Vertical frequency of the indication signal(string)

("000.00" Hz + NULL(0)+ NULL(0) )

DATA29 Picture mute

00H : OFF

01H : ON

DATA30 Sound mute

00H : OFF

01H : ON

DATA31 .. 32 Reserved

DATA33 Test pattern display 1

00H : No display (Normal condition)

00H Other : Displaying (Pattern ID)

Pattern ID Pattern Name MT LT LT80 HT GT WT VT NP

02H Cross Hatch x * x * x x x x

03H Gray Bars * * * * * * * *

04H Raster(0%) * * * * * * * *

05H Raster(25%) * * * * * * * *

06H Raster(50%) * * * * * * * *

07H Raster(100%) * * * * * * * *

08H Focus * * * * * * * *

09H Raster Blue * x * x * x * *

0AH Gray Raster 30 * * * * * * * *

17H Gray Raster 10 * * * * * * * *

18H RAMP WBRG x * x * x * x x

19H Blue Raster 60 x * x * x * x x

1DH Cross Hatch 3 * *1 * x * * * *

* : Supported

x : Not supported

*1: Only LT240K/260K

DATA34 Test pattern display 2

FFH: No display (Normal condition)

FFH Other: Displaying

Bit 2: BLUE pattern

0 = OFF

1 = ON

Bit 1: GREEN pattern

0 = OFF

1 = ON

Bit 0: RED pattern

0 = OFF

1 = ON

DATA35 .. 50 Reserved

DATA51 .. 65 User registration name ( 14 characters + NULL )

DATA66 Forced On-screen mute

00H : OFF

01H : ON

DATA67 On-screen display

00H : No display

01H : Displaying

Andere Handbücher für VT695

Dieses Handbuch passt für folgende Modelle

Andere NEC Projektor Handbücher

NEC

NEC NP-V300W Bedienungsanleitung

NEC

NEC PE506UL Bedienungsanleitung

NEC

NEC LT170 Bedienungsanleitung

NEC

NEC VT37 Bedienungsanleitung

NEC

NEC NP-NC1000C Bedienungsanleitung

NEC

NEC VT676 Series Bedienungsanleitung

NEC

NEC LT20E Handbuch

NEC

NEC LT260 Series Betriebsanleitung

NEC

NEC P502WL Bedienungsanleitung

NEC

NEC PX700W Bedienungsanleitung

NEC

NEC MultiSync XG85RP-CH Benutzerhandbuch

NEC

NEC P502H Bedienungsanleitung

NEC

NEC PA803UL Bedienungsanleitung

NEC

NEC P401W Bedienungsanleitung

NEC

NEC NC900C Bedienungsanleitung

NEC

NEC P554U Bedienungsanleitung

NEC

NEC NP905 - XGA LCD Projector Bedienungsanleitung

NEC

NEC HT410 Series Bedienungsanleitung

NEC

NEC NP-V300X Bedienungsanleitung

NEC

NEC LT380 - MultiSync XGA LCD Projector Bedienungsanleitung

NEC

NEC NP600 EDU Bedienungsanleitung

NEC

NEC MT1065 - MultiSync XGA LCD Projector Bedienungsanleitung

NEC

NEC PE456USL Bedienungsanleitung

NEC

NEC LT30 - INSTALLTION GUIDE Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung