NEC WT600 Series Bedienungsanleitung

[English]

WT600 SETUP GUIDE

[Deutsch]

AUFSTELLUNGSANLEITUNG WT600

[Français]

WT600 - GUIDE D’INSTALLATION

[Italiano]

GUIDA DI IMPOSTAZIONE WT600

[Español]

GUÍA DE INSTALACIÓN DE LA UNIDAD WT600

[Svenska]

WT600 INSTALLATIONSGUIDE

WT600 SETUP GUIDE

Contents

Screens Suited for the WT600 ........................................... E-2

Stands Suited for the WT600 ............................................. E-2

Ambient environmental condition ....................................... E-3

Part Names of the Projector ............................................... E-3

1. Setting Up the Screen and Projector .............................. E-4

2. Connections ................................................................... E-5

3. Opening the Mirror ......................................................... E-5

4. Switchng on the Power ................................................... E-6

5. Selecting Signals ............................................................ E-6

6. Adjusting the Position and Size of the Projected Image

(Focus Adjustments) ....................................................... E-7

7. Adjusting Pincushion or Barrel Distortion

(Pincushion) .................................................................. E-11

8. Troubleshooting ............................................................ E-13

POWER

ENTER

SOURCE

FOCUS

PCCARD

CANCEL

STATUS

LAMP

ON/

STANDBY

AUTO

ADJUST

REFORM

SELECT

PC CARD

AUDIOIN

/MONO

VIDEO IN S-VIDEO IN DVI-I IN RGB IN RGB OUT

DVI-I RGB

AUDIO IN

USB AUDIO OUT

PCCONTROL

REMOTE

NOTE

(1) The contents of this guide may not be reprinted in part or whole without permission.

(2) The contents of this guide are subject to change without notice.

(3) Great care has been taken in the creation of this guide; however, should any ques-

tionable points, errors, or omissions be apparent, please contact us.

(4) Notwithstanding Section (3), this company will not be responsible for any claims of

loss or profit or other matters deemed to be the result of using this unit.

(5) Guides with incorrect collating or missing pages will be replaced.

(6) When differences arise between this guide and the user's manual, this guide will be

given priority.

Scope of this Guide

The subject of this guide is to describe the procedure for adjusting the

image projected from the WT600 to the desired screen size. Descrip-

tions of screens and stands for use with the WT600 are also provided.

Please see the user's manual for information regarding the detailed

operation of the WT600 (hereafter referred to as "the unit" or "the pro-

jector").

E-1

WARNING

•Do not set up the projector, the screen or stand in a place that is not level or in an

unstable location.Doing so may result in the screen falling over or the projector falling

which may result in injury.

•When setting up the projector on the stand, first secure the top plate in a level condi-

tion. When the top plate is set at an angle, the projector may fall resulting in injury.

•Use a stand that can fully support the weight of the projector (which for this unit is

approximately 13lbs/5.9 kg). Failing to do so may result in the projector falling and

causing injury.

E-2

40"-100"

90˚

Screens Suited for the WT600

•Screens with a soiled, scratched, or discolored area will not produce a clean

image. Care should be used in the handling of the screen.

Recommended Not recommended

Recommended

Not recommended

Not optimal

Not recommended

•Use a panel or tension type screen that has a flat surface.

Do not use roll type screens and other screens that bend or

form a wavy surface easily. Doing so will result in increased

distortion of the projected image.

•The unit can accommdate screen sizes from 40” (81.3 cm/32.0” W ⳯61.0

cm/24.0” H) to 100 inch (203.2 cm/80.0” W ⳯152.4 cm/60.0” H).

•View the screen directly from the side so that it is perfectly

vertical.

A slanted screen will result in increased keystone distortion.

•In using this unit, increasing the screen size will move the projection position

upward.To accommodate this, please use a screen that has higher and lower

positioning adjustment. See Page 4 for information about the positioning rela-

tionships between the screen and this unit.

•High gain type screens are not optimal for use with this unit. The lower the

screen gain (i.e., screen gain on the order of 1), the better the appearance of

the projected image.

For more information about screen gain, consult catalogs from screen mak-

ers.

•Screen frames or pen shelves that protrude from the front of the screen sur-

face may block some of the light from the projector.

•Due to the projection angle of the unit, many standard rear projection screens

may produce uneven brightness, hot spotting or not produce maximum bright-

ness to the viewer. For more details utilizing rear projection screens and their

applications with this projector, please contact your NEC dealer.

•Controlled ambient light environments will allow for an image of higher con-

trast and depth to be displayed.

Level

Stands Suited for the WT600

•Use a stand that will allow this unit to be set up in a level condition. Turn the

foot of this unit and adjust so that the unit is level.

Recommended

•In using this unit, increasing the screen size will move the projection position

upward.To accommodate this, please use a stand that has a height position-

ing adjustment. See Page E-4 for information about the positioning relation-

ships between the screen and this unit.

E-3

Ambient environmental condition

•Do not place the screen near vents.

Air blow hits the screen, causing the projected image to ripple.

POWER

ENTER

SOURCE

FOCUS

PC CARD

CANCEL

STATUS

LAMP

ON/

STAND BY

AUTO

ADJUST

REFORM

SELECT

PCCARD

AUDIOIN

/MONO

VIDEOIN S-VIDEOIN DVI-IIN RGBIN RGBOUT

DVI-I RGB

AUDIOIN

USBAUDIOOUT

PCCONTROL

REMOTE

Part Names of the Projector

Front view

Rear view

Mirror cover

Open the mirror cover first before projecting an im-

age. See page E-5.

Avoid opening or closing the mirror cover quickly and

roughly.

Mirror cover lock switch

Slide this lock switch to the unlock position first before

opening the mirror cover.

After closing the mirror cover, slide the lock switch to

the lock position.

Foot (four feet on bottom)

Adjust the height by rotating each foot to keep the pro-

jector in a horizontal position. Each foot can be ex-

tended up to 1.2"(30mm).

Cabinet controls

The controls on the projector cabinet allows for power

on/off, source selection and other button operations.

See page E-6.

Terminal panel

Connect the RGB signal cable and other cables here.

See page E-5.

Main power switch

To turn on the main power to the projector, press the

Main Power switch to the ON position (l).The projec-

tor is in the Idle or standby mode and becomes ready

to use. See page E-6.

AC IN input

Connect the supplied power cable here. See page E-

Foot (four feet on bottom)

NOTE : For more information on part names of the projector,see page 1-2 of the user's manual.

•Do not illuminate the projector with strong light source such as halogen lamp.

Doing so can cause the object detection sensor to malfunction, resulting in the projector not

turning on.

1. Setting Up the Screen and Projector

1. Refer to "Throw Distance (C)" in the diagram and use a distance between the screen

and projector that corresponds to the screen size.

As an example, when projecting to a 60" screen, set the projector with a separation of

approximately 10.4"/26.3 cm from the screen.

2. Refer to "Height (D)" below and adjust the screen height, or adjust the height of the

projector stand.

As an example, when projecting to a 60" screen, adjust the height from the bottom surface

of the projector to the lower edge of the screen to approximately 19.0"/48.2 cm.

E-4

Back of

projector Projector

foot

Screen center

100

120

051015 20 25 30

Throw distance C (inch)

Screen size (inch)

100

120

0 100 200 300 400 500 600 700

Throw distance C (mm)

Screen size (inch)

100

114

164

214

263

313

332

362

381

412

441

461

500

510

559

609

619

659

2.5

4.5

6.4

8.4

10.4

12.3

13.1

14.3

15.0

16.2

17.4

18.1

19.7

20.1

22.0

24.0

24.4

25.9

Screen size

(inch) Throw distance (C)

mm inch

354

386

418

450

482

514

526

546

558

577

596

609

635

641

673

704

711

737

13.9

15.2

16.5

17.7

19.0

20.2

20.7

21.5

22.0

22.7

23.5

24.0

25.0

25.2

26.5

27.7

28.0

29.0

Height (D)

mm inch

Height (B)

mm inch

NOTE

•There is a tolerance of +5% because of design values.

•The projection distance and the lower edge of the

screen are calculated using a 4:3 aspect ratio.

659

729

799

869

939

1010

1037

1080

1107

1149

1191

1219

1275

1289

1359

1428

1443

1499

25.9

28.7

31.5

34.2

37.0

39.7

40.8

42.5

43.6

45.2

46.9

48.0

50.2

50.7

53.5

56.2

56.8

59.0

E-5

2. Connections

1. Connect the supplied 15pin-15pin signal cable.

For older Macintosh computers, use a commercially available pin adapter to connect to your

Macintosh’s video port.

NOTE : Power down all equipment before making connections.

POWER

ENTER

SOURCE

FOCUS

PC CARD

CANCEL

STATUS

LAMP

ON/

STANDBY

AUTO

ADJUST

REFORM

SELECT

PCCARD

AUDIOIN

/MONO

VIDEOINS-VIDEOIN DVI-IINRGBINRGBOUT

DVI-IRGB

AUDIOIN

USBAUDIOOUT

PCCONTROL

REMOTE

RGB IN

RGB signal cable (supplied)

POWER

ENTER

SOURCE

FOCUS

PCCARD

CANCEL

STATUS

LAMP

ON/

STANDBY

AUTO

ADJUST

REFORM

SELECT

PC CARD

AUDIO IN

/MONO

VIDEO IN S-VIDEO IN DVI-I IN RGB IN RGB OUT

DVI-I RGB

AUDIO IN

USBAU

DIO OUT

PCCONTROL

REMOTE

2. Connect the supplied power cable.

POWER

ENTERCANCEL

STATUS

LAMP

ON/

STANDBY

AUTO

ADJUST

REFORM

SELECT

RGBIN RGBOUT

DVI-IRGB

AUDIOIN

USBAUDIOOUT

POWER

ENTER CANCEL

STATUS

LAMP

ON/

STANDBY

AUTO

ADJUST

REFORM

SELECT

RGBIN RGBOUT

DVI-I RGB

AUDIOIN

USB AUDIOOUT

3. Opening the mirror

1. Slide the mirror cover lock switch to the unlock position.

2. Slowly open the mirror cover holding both ends.

NOTE:

•Do not release your hold of the mirror cover until fully open.

•Do not apply excessively strong pressure against the mirror

cover or mirror surface while opening it.

•Keep finger prints off the mirror surface. Leaving finger prints

in the mirror surface might cause an unwanted shadow and

poor picture quality.

If the mirror surface is soiled with finger prints, wipe them off

with the supplied cleaning cloth. See page 7-2 of the user's

manual.

4. Switching on the Power

1.Turn on the main power switch.

ENTER CANCEL

STATUS

LAMP

ON/

STAND BY

AUTO

ADJUST

REFORM

POWER

ENTER CANCEL

STATUS

LAMP

ON/

STAND BY

AUTO

ADJUST

REFORM

POWER

OFF

VIDEO

AUTO ADJ.

RGB VIEWER

LASER

SELECT

POWER

2.Turn on the projector.

To turn on the power to the projector, press and hold

the ON/STAND BY button on the projector cabinet or

the POWER ON button on the remote control for a

minimum of 2 seconds.

NOTE : To turn off the projector, press and hold the

ON/STAND BY button or the POWER OFF button for

a minimum of 2 seconds.

Note on Startup screen (Menu Language Select

screen)

When you first turn on the projector, you will get the

Startup screen. This screen gives you the opportu-

nity to select one of the seven menu languages:

English, German, French, Italian, Spanish, Swedish

and Japanese. (See page 3-1 of the user’s manual)

To turn on the main power to the projector,

press the Main Power switch to the ON position

( I ).

NOTE: Before you turn on your projector,

ensure that the computer is turned on.

The POWER indicator will light orange (In the

Idle mode the STATUS indicator will light green

as well). The projector is in the Idle or Standby

mode.

SOURCE

FOCUS

PC CARD

SELECT

OFF

VIDEO

AUTO ADJ.

RGB VIEWER

LASER

SELECT

POWER

5. Selecting Signals

Press and hold the SOURCE button for a

minimum of 1 second, the projector will search

for the next available input source. When using

the remote control, press the RGB button for the

RGB source.

NOTE:

•When projecting the image from a personal

computer and the image edge is cut off or the

projection is poor, press the AUTO ADJUST

button (which is labeled AUTO ADJ. on the

remote control) and the projector will perform

the adjustment automatically.

•When the image from the personal computer

is not projected, see "Common Problems &

Solutions" on page E-14.

E-6

Projector's left side Cabinet controls

Cabinet controls Remote control

E-7

90˚

1. Check whether the screen is set up to be vertical by

viewing it from the side.

6. Adjusting the Position and Size of the Projected Image

(Focus Adjustments)

•After turning on the power, projected images may flicker for 3 to 5 minutes until the lamp

lighting is stabilized.

Also after turning on the projector, the picture position may be slightly changed.

Wait 10 minutes until the light status and projected images become stable.

•If the screen is tilted vertically or horizontally, keystone distortion becomes large. Proceed the

following steps to correctly set up the projector and the screen.

2. Check that the projector is level and that it is set to

be parallel with the screen.

SOURCE

FOCUS

PC CARD

SELECT

ASPECT FREEZE

FOCUS

3D REFORM

HELP

POINTER

VOLUME MAGNIFY

ZOOM

PIC-MUTE

SLIDE

FOLDER

SLIDE

LIST

3. Press the FOCUS buttons and align the focus of the projected image.

A press of the FOCUS buttons results in focus being taken simultaneously with the adjust-

ment of vertical keystone distortion. See page E-9.

°



Top view Side view

Screen surface

Parallel

Align the projector

center with the

screen center

Bottom of projector

Cabinet controls Remote control

Andere Handbücher für WT600 Series

Inhaltsverzeichnis

Sprachen:

Andere NEC Projektor Handbücher

NEC

NEC LT240K, LT260K Bedienungsanleitung

NEC

NEC NC900C-A Bedienungsanleitung

NEC

NEC PH1202HL1 Bedienungsanleitung

NEC

NEC SX10000 Bedienungsanleitung

NEC

NEC VT695 Bedienungsanleitung

NEC

NEC PH1000U Bedienungsanleitung

NEC

NEC NP1250 Series Bedienungsanleitung

NEC

NEC PG-6200 Bedienungsanleitung

NEC

NEC XL-3500 Bedienungsanleitung

NEC

NEC NP41G Bedienungsanleitung

NEC

NEC NP110 - SVGA DLP Projector Bedienungsanleitung

NEC

NEC LT20 - XGA DLP Projector Bedienungsanleitung

NEC

NEC NP1150 XGA Bedienungsanleitung

NEC

NEC DLP Cinema NP- NC2403ML Bedienungsanleitung

NEC

NEC NEC L51W LED Bedienungsanleitung

NEC

NEC NP210 Bedienungsanleitung

NEC

NEC NP-PX750U Bedienungsanleitung

NEC

NEC NP-M300X Bedienungsanleitung

NEC

NEC LT50 - Bedienungsanleitung

NEC

NEC PV800UL-W Bedienungsanleitung

NEC

NEC PX1005QL-W Bedienungsanleitung

NEC

NEC NP300 Series Bedienungsanleitung

NEC

NEC NP4001-07ZL Bedienungsanleitung

NEC

NEC VT490 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung