NEC Express5800 320La Bedienungsanleitung

System Release Notes

Express5800/320La

System Release Notes

PN: 455-01623-003

Proprietary Notice and Liability Disclaimer

The information disclosed in this document, including all designs and related materials, is

the valuable property of NEC Solutions (America), Inc. and/or its licensors. NEC Solutions

(America), Inc. and/or its licensors, as appropriate, reserve all patent, copyright and other

proprietary rights to this document, including all design, manufacturing, reproduction, use,

and sales rights thereto, except to the extent said rights are expressly granted to others.

The NEC Solutions (America), Inc. product(s) discussed in this document are warranted in

accordance with the terms of the Warranty Statement accompanying each product.

However, actual performance of each product is dependent upon factors such as system

configuration, customer data, and operator control. Since implementation by customers of

each product may vary, the suitability of specific product configurations and applications

must be determined by the customer and is not warranted by NEC Solutions (America), Inc.

To allow for design and specification improvements, the information in this document is

subject to change at any time, without notice. Reproduction of this document or portions

thereof without prior written approval of NEC Solutions (America), Inc. is prohibited.

Trademarks

Linux is a registered trademark of Linus Torvalds, Inc.

Microsoft and Windows 2000 are registered trademarks of Microsoft Corporation.

All other product, brand, or trade names used in this publication are the trademarks or registered trademarks

of their respective trademark owners.

PN: 455-01623-003 March 2003

NEC Solutions (America), Inc

10850 Gold Center Drive, Suite 200,

Rancho Cordova, CA 95670

Express5800/320La

System Release Notes

The Express5800/320La System Release Notes provide up-to-date information

on your system. These notes also provide additional valuable information about

your system that was not included in the user’s guide at the time of its release.

Please read these notes in their entirety.

CONTENTS

Introduction ............................................................................................................................................3

Operating System ...................................................................................................................................3

Advisories...............................................................................................................................................3

EXPRESSBUILDER .........................................................................................................................3

BIOS and SCSI ID Settings ...............................................................................................................3

TCP/IP Protocol Settings for Windows 2000.....................................................................................4

Disk Failure Prediction (S.M.A.R.T) .................................................................................................4

SCSI Controller Errors.......................................................................................................................4

Configuring the APC SNMP Management Card for Windows 2000.................................................5

System Hardware...............................................................................................................................6

Documentation Errata.............................................................................................................................7

Express5800/ft Series EXPRESSBUILDER User’s Guide................................................................7

Express5800/320La/320La-R User’s Guide.....................................................................................13

Express5800/320La/320La-R Service Guide...................................................................................15

nec

Express5800/320La System Release Notes 3

Introduction

These System Release Notes cover the following topics:

!Operating System

!Advisories

!Documentation Errata

Operating System

Your server supports Microsoft®Windows®2000 Advanced Server with

Service Pack 3 and above and also Ft Linux. No other operating systems are

supported at this time.

Advisories

This section contains advisories on EXPRESSBUILDER, BIOS, SCSI ID

settings, TCP/IP protocol settings, disk failure prediction, SCSI controller errors

and system hardware.

EXPRESSBUILDER

The following advisory applies to EXPRESSBUILDER.

!Install Windows 2000 Operating System using the Ft Server Setup function

on EXPRESSBUILDER. Do not attempt to install the operating system

manually.

BIOS and SCSI ID Settings

The following advisories apply to BIOS and SCSI ID settings.

!Before you install Windows 2000 Operating system, run BIOS Setup and set

Boot Monitoring to DISABLE. After the operating system is completely

installed, run BIOS Setup again and set Boot Monitoring to ENABLE. Refer

to your user’s guide for information on running BIOS Setup.

!The SCSI ID of the Host Bus Adapter (HBA) on SCSI bus 1 is set to ID 6 at

the factory. If the SCSI BIOS defaults are loaded, the SCSI ID of the Host

Bus Adapter (HBA) on SCSI bus 1 must be reset to 6. In addition, ensure

greater than 4Gbyte addressing is enabled to allow disk sizes larger than

4GB on both controllers. Updated procedures for enabling greater than

4Gbyte addressing are provided in these System Release Notes.

4Express5800/320La System Release Notes

TCP/IP Protocol Settings for Windows 2000

If you have computers that communicate with the NEC EXPRESS5800/ft server

using TCP/IP protocols, you must make several settings to your ft server to

allow communications without interruptions. These setting changes must also be

made in all clients connected to the EXPRESS5800/ft server via the network.

Note: If Windows 2000 Advanced Server is preloaded

on your system, you do not need to perform this procedure

on your ft server. However, this procedure should be

performed on all computers connected to your ft server.

1. Power up the server and its peripherals.

2. Insert the EXPRESSBUILDER CD disk in the CD-ROM drive. Immediately

press and hold down the Shift key to prevent auto start.

3. In Windows Explorer or My Computer, locate the CD-ROM drive (labeled

2001 ag) containing the EXPRESSBUILDER CD disk.

!Locate the WinNT folder and double click on it.

!Double click on W2K.

!In the W2K folder, find and copy Ftreg.exe into an arbitrary directory

on your hard drive.

4. Activate the command prompt, enter the directory containing the above file

copy, and then execute the following command:

FTREG.EXE

Executing FTREG.EXE makes changes to your system registry to avoid a

timeout during initial communications between the NEC EXPRESS5800/ft

server and computers on the network using TCP/IP protocols.

Disk Failure Prediction (S.M.A.R.T)

Disk failure prediction S.M.A.R.T (Self-Monitoring Analysis and Reporting

Technology) is not supported. When running the ft Server Utility, do not enable

“Disk Failure Prediction (S.M.A.R.T.).”

SCSI Controller Errors

During a tape backup, the Event Log may record an erroneous sraql180 SCSI

controller error. The error description is “the driver detected a controller error

on \Device\SCSI\sraq1801. If the detailed data includes word “f0030015,”

ignore this error as the tape backup is functioning normally.

Express5800/320La System Release Notes 5

The Event Log may occasionally record an erroneous sraql160 SCSI controller

error. The error description is “the driver detected a controller error on

\Device\SCSI\sraq1602. If the detailed data includes word “f0030015 or

f0030004,” and this error occurs only once or twice a week, ignore this error as

it is caused by hard disk drive operating system interaction and is self-

correcting. If however, your ft Server is experiencing ten or more such errors in

a week, a hard disk drive error is suspected. Contact your technical support

representative.

Configuring the APC SNMP Management Card for Windows 2000

These instructions detail the configuration of the 320La server with the APC

SmartUPS, NEC order number 050-02049-000.

1. Install the SNMP management card into the UPS. Refer to the APC

installation manual that came with the card for instructions.

2. Configure the IP address of the management card. Note this may require

connection of the serial cable from the server to the UPS, and then removal

once configuration has been completed. The IP address of the SNMP

management card should be on the same subnet as the 320La server. For

additional information regarding configuring the IP address of the SNMP

card via serial connection, refer to the manual that came with the card.

3. Connect the SNMP management card to the network.

4. Using a web browser on the 320La server, type in the IP address configured

in step 2. The APC SNMP login screen displays.

5. Login to the APC SNMP card using “apc” for both the username and

password. The “APC Web-SNMP Management Card” menu displays.

6. On the left side of the display screen, click on “Events,” then “Recipients”

and configure the trap receivers for the SNMP community by entering the IP

address of the management station in the Receiver NMS IP field. Be sure to

click apply when done.

7. On the left side of the display screen, click on “Network” and then “SNMP”

to configure the community name and Receiver NMS IP address. Access

control should be set to write. Be sure to click apply when done.

8. Download and install the free software package “APC PowerChute Network

Shutdown”. This software can be found at the following URL:

http://www.apcc.com/tools/download/

9. Once installed, access the user interface via the start menu. (Start |

Programs | PowerChute network shutdown | user interface).

10.Login using “apc” as both the username and password. The “PowerChute

Network Shutdown” menu displays.

11.On the left side of the display screen, click on “ Configure Events” then the

“Change Settings” button.

6Express5800/320La System Release Notes

12.Select both the “Communication: Lost while on battery” and “UPS: On

Battery” entries in the list. (For multiple selections, hold down the control

key while clicking with the mouse. Additional events may be configured

later as required).

13.Click next and ensure “logging” is enabled.

14.Click next and select “user notification” as required.

15.Click next and specify “command line,” if required.

16.Click next and place a check mark in the box for “Yes, I want to shut down

the system.”

17.Click next, then click “finish.”

18.Configuration is complete. When the UPS detects a power utility failure, it

will notify the management station, as well as shut down the system.

System Hardware

The following advisory applies to the USB connections on your server.

!If you unplug the keyboard or mouse cable from the USB port on your

system, do not reinsert the cable for at least 10 seconds.

Express5800/320La System Release Notes 7

Documentation Errata

Express5800/ft Series EXPRESSBUILDER User’s Guide

Please note the following corrections to the Express5800/ft Series

EXPRESSBUILDER User’s Guide, 456-01574-001.

Chapter 2 – Initial Setup

Initial Setup procedures have changed. Use the following procedures for

performing "Initial Setup" before performing the Windows 2000 Advanced

Server installation.

Note: If Windows 2000 Advanced Server is preloaded

on your system, you do not need to perform these Initial

Setup Procedures.

Initial Setup

Perform the initial setup procedures before performing the Windows 2000

Advanced Server installation. Initial setup will perform the following functions.

!Enable the greater than 4Gbyte disc geometry in each PCI module

!Change the system BIOS setting to disable Boot Monitoring.

1. Power down the server.

2. Ensure the mouse, keyboard and monitor are connected to the server.

3. Disconnect PCI module 1 from the system backplane.

!Unlock and open the front door on the tower cabinet or front covers on

the rack-mount system. Refer to Chapter 4 of your System User’s Guide

for information on opening the system front door or system front covers.

!Unscrew the knurled screw securing the locking handle to the PCI

module 1. See Figure 2-1.

8Express5800/320La System Release Notes

Knurled

Screws

Figure 2-1. Removing the Knurled Screw Securing the Locking Handle

!Pull the locking handle all the way up to its unlocked position.

See Figure 2-2.

Figure 2-2. Releasing the Locking Handle and PCI Module

!Using the locking handle, pull the PCI module out of the chassis just

enough to disconnect the module from the system backplane.

4. Power up the server.

5. At the startup screen, when prompted, press F2 to enter the BIOS Setup and

disable Boot Monitoring.

!Select Advanced on the BIOS Setup Main Menu.

!Select Monitoring Configuration and press Enter.

!Select Boot Monitoring and change the setting to Disabled to disable

Boot Monitoring.

Andere Handbücher für Express5800 320La

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NEC Server Handbücher

NEC

NEC 120Rf-2 Bedienungsanleitung

NEC

NEC SX-Aurora TSUBASA A300-2 Bedienungsanleitung

NEC

NEC LS2400 Bedienungsanleitung

NEC

NEC 5800 Series Bedienungsanleitung

NEC

NEC NEC Express5800 Series Anleitung zur Verwendung

NEC

NEC Express 5800 Bedienungsanleitung

NEC

NEC Express5800/120Rg-2 Bedienungsanleitung

NEC

NEC Express5800/120Rg-1 Bedienungsanleitung

NEC

NEC NEC Express5800 Series Montageanleitung

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC Express5800/120Rj-2 Bedienungsanleitung

NEC

NEC Express5800 120Li Bedienungsanleitung

NEC

NEC NEC Express5800 Series Bedienungsanleitung

NEC

NEC NE3108-007 Bedienungsanleitung

NEC

NEC UNIVERGE NEAX 2000 IPS Bedienungsanleitung

NEC

NEC Express5800 120Ed Referenzhandbuch

NEC

NEC E120e-M Bedienungsanleitung

NEC

NEC Express5800/T110f-E Bedienungsanleitung

NEC

NEC Express5800/120Rh-2 Bedienungsanleitung

NEC

NEC SV8300 Montageanleitung

NEC

NEC HV8600 Bedienungsanleitung

NEC

NEC Express5800/120Rh-2 Bedienungsanleitung

NEC

NEC NEAX IPS NWA-008869-001 Bedienungsanleitung

NEC

NEC Expres5800/A2040b Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung