Nedap WIM Bedienungsanleitung

WIM

installation guide

2017

-01-17 | v4.4 | 5279348

WIM | INSTALLATION GUIDE

Content

2/20

CONTENT

1INTRODUCTION _______________________________________________________ 3

1.1 KEY FEATURES __________________________________________________ 3

2INSTALLATION ________________________________________________________ 4

2.1 SAFETY PRECAUTIONS ___________________________________________ 4

2.2 DIMENSIONS ___________________________________________________ 4

3CONNECTIONS ________________________________________________________ 5

4ANPR CONFIGURATION _________________________________________________ 7

4.1 PLATE READER SETTINGS _________________________________________ 7

4.1.1 EVENTS / ACTIONS ________________________________________ 7

4.2 SYSTEM SETTINGS _______________________________________________ 7

4.2.1 SERIAL PORTS ____________________________________________ 7

5PLATE CONVERSION MODES ____________________________________________ 8

5.1 WIEGAND 26-BIT (SHA-1)_________________________________________ 8

5.2 WIEGAND 64-BIT ________________________________________________ 8

5.3 WIEGAND MATCH-LIST MODE ____________________________________ 10

5.4 MAGSTRIPE ISO7811 TRACK 1____________________________________ 11

5.5 MAGSTRIPE ISO7811 TRACK 2____________________________________ 12

5.6 BARCODE WAND EMULATION CODE39 ____________________________ 13

6PROGRAMMER'S GUIDE _______________________________________________ 15

6.1 MESSAGE FORMAT _____________________________________________ 15

6.2 COMMAND MESSAGES __________________________________________ 15

ATECHINAL SPECIFICATIONS_____________________________________________ 18

BDISCLAIMER _________________________________________________________ 19

CDOCUMENT REVISION _________________________________________________ 20

WIM | INSTALLATION GUIDE

Introduction

3/20

1INTRODUCTION

The Wiegand Interface Module (WIM) is developed to be used in combination with

the License Plate Reader. The WIM will convert the license plate string into a

Wiegand output message. The Wiegand interface is supported by many access

control systems.

1.1 KEY FEATURES

•Converts a license plate into a Wiegand output message.

•Output in magstripe or barcode format is also possible.

•Easy integration into existing access control systems.

•Easy user configuration.

•Contains a match-list in which license plates and corresponding Wiegand

output numbers are found.

•Supports a sophisticated algorithm to convert license plates into "unique"

Wiegand output numbers.

•RS485 interface to connect the NEDAP ANPR license plate reader.

•LAN – TCP/IP interface to configure the device and manage the match-list.

WIM | INSTALLATION GUIDE

Installation

4/20

2INSTALLATION

2.1 SAFETY PRECAUTIONS

The following safety precautions must be observed during normal use, service and

repair.

•Disconnect the power supply before opening the device.

•The WIM shall only be installed and serviced by qualified and trained

personnel.

•The WIM can be powered from a low power, Class 2 power supply, in

compliance with local regulations.

•To be sure of safety, do not modify or add anything other than mentioned in

this manual or indicated by NEDAP N.V.

2.2 DIMENSIONS

Figure 1: WIM housing dimensions

125 mm [ 4.9 " ]

35 mm [ 1.4 " ]

130 mm [ 5.1 " ]

WIM | INSTALLATION GUIDE

Connections

5/20

3CONNECTIONS

Below the connections are shown which are available on front panel of the device.

Shielded cable shall be used for all connections except power supply.

Figure 2: Front view

RS485 Connect the RS485 to the License Plate Reader (9600, 8N1).

A: RS485-A (yellow)

B: RS485-B (green)

GND: RS485-GND (purple)

WIEGAND Connect the Wiegand output to your access control system.

D1: Wiegand data-1 (white)

D0: Wiegand data-0 (green)

GND: Ground (black)

MAGSTRIPE Magstripe Clock and Data output.

Select with the plate conversion mode switches. See for more

details chapter 5.

D1: Data

D0: Clock

CLS: Card Loaded

GND: Ground

BARCODE Barcode wand emulation data output in code39 format.

Select with the plate conversion mode switches. See for more

details chapter 5.

D1: Wand emulation data output (black=high)

D0: Wand emulation data output (black=low)

GND: Ground

STS LED Status LED (green)

Blinks regularly to indicate standby.

Blinks fast to indicate that a RS485 message (license plate) is

processed.

ERR LED Error LED (red)

Normally off.

On if match-list used and license plate not found.

LAN The LAN connection (RJ45 socket) is used to configure the

device and manage the match-list.

Link LED (left): Off=No link, Amber=10Mbps,

Green=100Mbps.

Activity LED (right): Off=No activity, Amber=HDX

Activity, Green=FDX Activity.

RS485

connection

WIEGAND

output

LED

indications

LAN

connection

GND

CLS

GND

WIM | INSTALLATION GUIDE

Connections

6/20

The power supply and the DIP-switches are located on the rear panel. See the

picture below.

Figure 3: Rear view

Power input Use the supplied 24VDC power adapter.

Power supplies must be able to supply 12 – 24 VDC / 5 Watt

(positive voltage at center pin).

Switches The switches select the plate conversion mode. See for more

details chapter 5.

Switches

Power input

WIM | INSTALLATION GUIDE

ANPR Configuration

7/20

4ANPR CONFIGURATION

This chapter describes the required plate reader settings when using the WIM. These

settings must be configured in the plate reader using a web browser and the plate

reader's TCPIP interface. See for more details about the plate reader the ANPR

installation guide.

4.1 PLATE READER SETTINGS

4.1.1 EVENTS / ACTIONS

The OCR Read event must generate an RS485 output message as specified below.

Optionally enable the OCR Not Read event to output a NOTREAD message.

Optionally enable the OCR No Plate event to output a NOPLATE message.

OCR Read – 485 Msg

Enable: YES

Message: %PLATE_STRING%0x0D%0x0A

OCR Not Read – 485 Msg

Enable: YES | NO

Message: NOTREAD%0x0D%0x0A

OCR No Plate – 485 Msg

Enable: YES | NO

Message: NOPLATE%0x0D%0x0A

4.2 SYSTEM SETTINGS

4.2.1 SERIAL PORTS

The RS485 serial port must be enabled as specified below.

Enable: YES

Baud rate: 9600

Parity: NONE

Data Bit: 8

Stop Bit: 1

Message: RAW

WIM | INSTALLATION GUIDE

Plate Conversion Modes

8/20

5PLATE CONVERSION MODES

The plate conversion mode is selected using the 4 switches located on the device

rear panel.

Plate Conversion Mode

Mode

Hex

Wiegand 26-bit SHA-1 (see chapter 5.1)

Wiegand 64-bit (see chapter 5.2)

OFF

Magstripe ISO7811 track 1 (see chapter 5.4)

OFF

Magstripe ISO7811 track 2 (see chapter 5.5)

OFF

Barcode code39 emulation (see chapter 5.6)

OFF

Wiegand match-list mode (see chapter 5.3)

OFF

Wiegand match-list-XL mode (see chapter 5.3)

OFF

5.1 WIEGAND 26-BIT (SHA-1)

In this mode, every received license plate message is converted to a Wiegand 26-bit

output message using the SHA-1 security hashing algorithm.

Wiegand 26-bit SHA-1 conversion procedure:

1Receive license plate message hk 55 evb

2Turn into upper case HK 55 EVB

3Remove spaces HK55EVB

4Calculate SHA-1 digest A44F633C 8A6D1581

50CCEB3E F83D9DE0

BA80CF15

5Truncate. Keep least significant 24-bits A80CF15

6Add parity bits according to Wiegand 26-bit format

The WIM_Calc software is available to calculate Wiegand output numbers for

specific license plates.

Figure 4: WIM_Calc software screenshot

5.2 WIEGAND 64-BIT

In this mode, every received license plate message is converted to a Wiegand 64-bit

Note

Wiegand 26-bit (SHA-1)

mode it is not required to

use the LAN connection.

Note

Wiegand 64-bit mode it

is not required to use the

LAN connection.

WIM | INSTALLATION GUIDE

Plate Conversion Modes

9/20

output message.

The first four bits are always 0110.

Next 10 groups of 6 bits. Each 6-bit group contains a license plate character. See

character conversion table below.

If the license plate string contains less than 10 characters, the first groups are «

empty » (= 000000).

If a character is not found in the conversion table, then the conversion uses

« other » (=111111).

CHAR

6-BIT

CHAR

6-BIT

CHAR

6-BIT

CHAR

6-BIT

'0'

010000

'A'

011010

'K'

100100

'U'

101110

'1'

010001

'B'

011011

'L'

100101

'V'

101111

'2'

010010

'C'

011100

'M'

100110

'W'

110000

'3'

010011

'D'

011101

'N'

100111

'X'

110001

'4'

010100

'E'

011110

'O'

101000

'Y'

110010

'5'

010101

'F'

011111

'P'

101001

'Z'

110011

'6'

010110

'G'

100000

'Q'

101010

'7'

010111

'H'

100001

'R'

101011

'8'

011000

'I'

100010

'S'

101100

« empty »

000000

'9'

011001

'J'

100011

'T'

101101

« other »

111111

Table 1: character conversion table

The WIM_Calc software is able to calculate the Wiegand 64-bit output numbers for

specific license plates.

Examples:

License plate 'HK55EVB':

License plate 'VR46#T':

«empty»

WIM | INSTALLATION GUIDE

Plate Conversion Modes

10/20

5.3 WIEGAND MATCH-LIST MODE

In the Wiegand match-list mode, every received license plate message is searched in

the match-list. If the plate string is found, then the corresponding Wiegand output

message will be transmitted. If the plate string is not found, then no Wiegand output

is generated. Optionally a defined Wiegand output message can be transmitted

when no match is found.

The match-list or match-list XL mode is selected with the dip-switches.

Match-list (mode 00)

Match-list xl (mode 04)

Memory

EEPROM

FLASH

Capacity

1008 plates

20480 plates

Write endurance

1M times

100K times

Read/search speed 133µsec / plate

max = 130µsec x 1008 =

135msec

8µsec / plate

max = 8µsec x 20480 =

160msec

The match-list is managed through the LAN interface. This can be done using the

WIM_List software.

See below a screenshot of the WIM_List software.

Figure 5: WIM_List software screenshot

The WIM_List software shows on the left side the match-list. New plates and

numbers can be added to the list. Remove plates by using the popup menu or

pressing the delete key. To view or edit the special plates or the Wiegand output

format, it is required to select the Expert user mode.

On the right side the devices (Wiegand Interface Modules) are shown. Click the

Search button to scan for devices. System administrators and installers require user

mode Expert to configure the devices (e.g. assign an IP address).

Click the transit ('>') or receive ('<') button to synchronize the match-list with the

Andere Handbücher für WIM

Inhaltsverzeichnis

Andere Nedap Steuereinheit Handbücher

Nedap

Nedap WIM Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung