Nedap AEOS Blue Bedienungs- und Wartungsanleitung

Installation and Configuration

AEOS Blue and

vehicle identification

TRANSIT, uPASS, ANPR

Version

06-08-2019

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 32/48

Date Version Changes

06-08-2019

Changed instructions or the ANPR LUMO long range vehicle identification

reader, via TCP/IP (chapter 5), IpBadge

26-06-2019 2

Added instructions for the ANPR LUMO long range vehicle identification

reader, via TCP/IP (chapter 5) or Serial (chapter 6).

Corrections in the AEmon and AEOS configuration for the TRANSIT Ultimate

reader.

22-05-2019 1 New document

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 33/48

Contents

1. INTRODUCTION 5

2. TRANSIT ULTIMATE (FOR WIEGAND) 6

2.1 CONNECTION OVERVIEW 6

2.2 CONFIGURING THE TRANSIT READER (FOR WIEGAND) 7

UPDATE THE TRANSIT READER FIRMWARE (IF NECESSARY) 7

TEST THE COMMUNICATION8

ADJUST THE DIP SWITCH 9

2.3 CONFIGURING AEMON (FOR WIEGAND) 9

CONFIGURE THE IDENTIFIER TYPE IN AEMON 9

2.4 CONFIGURING AEOS (FOR WIEGAND) 12

DEFINE THE IDENTIFIER TYPE IN AEOS 12

CHECK THE AEOS EVENT LOG 12

3. UPASS 13

3.1 CONNECTION OVERVIEWS 13

3.1.1 CONNECTION OVERVIEW UPASS ACCESS 13

3.1.2 CONNECTION OVERVIEW UPASS REACH 14

3.1.3 CONNECTION OVERVIEW UPASS TARGET 15

3.2 CONFIGURE THE UPASS READER (FOR WIEGAND) 16

RETRIEVE CARD INFORMATION (IF NECESSARY) 16

SET THE UPASS READER TO UHF MODE 17

3.3 CONFIGURE THE UPASS READER (FOR NEDAP XS) 17

RETRIEVE CARD INFORMATION (IF NECESSARY) 17

SET THE UPASS READER TO TRANSIT MODE 18

UPDATE THE UPASS READER FIRMWARE (IF NECESSARY) 19

TEST THE COMMUNICATION 20

ADJUST THE DIP SWITCH 21

3.4 CONFIGURING AEMON 21

CONFIGURE THE IDENTIFIER TYPE IN AEMON 21

3.5 CONFIGURING AEOS 23

DEFINE THE IDENTIFIER TYPE IN AEOS 23

ISSUE AN IDENTIFIER 24

CHECK THE AEOS EVENT LOG 24

4. ANPR ACCESS FOR TCP/IP 25

4.1 CONNECTION OVERVIEW 25

4.2 CONFIGURING THE ANPR ACCESS READER FOR TCP/IP 25

CONFIGURE THE ANPR ACCESS READER 26

4.3 CONFIGURING AEMON 27

CONFIGURE THE IDENTIFIER TYPE IN AEMON 27

4.4 CONFIGURING AEOS 29

DEFINE THE IDENTIFIER TYPE IN AEOS 29

ISSUE THE LICENCE PLATE NUMBER AS IDENTIFIER 30

CHECK THE AEOS EVENT LOG 30

5. ANPR LUMO FOR TCP/IP 31

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 34/48

5.1 CONFIGURING THE ANPR LUMO READER FOR TCP/IP 31

CONFIGURE THE ANPR LUMO READER 31

5.2CONFIGURING AEMON FOR TCP/IP ─WITH IPBADGE 33

CONFIGURE THE IDENTIFIER TYPE IN AEMON 33

5.3 CONFIGURING AEMON FOR TCP/IP ─WITH GENERIC MESSAGE MAPPER 36

CONFIGURE THE IDENTIFIER TYPE IN AEMON 36

5.4 CONFIGURING AEOS 39

DEFINE THE IDENTIFIER TYPE IN AEOS 39

ISSUE THE LICENCE PLATE NUMBER AS IDENTIFIER 39

CHECK THE AEOS EVENT LOG 40

6. ANPR LUMO VIA SERIAL 41

6.1 CONFIGURING THE ANPR LUMO READER 41

CONFIGURE THE ANPR LUMO READER 41

6.2CONFIGURING AEMON 42

CONFIGURE THE IDENTIFIER TYPE IN AEMON 42

6.3 CONFIGURING AEOS 46

DEFINE THE IDENTIFIER TYPE IN AEOS 46

ISSUE THE LICENCE PLATE NUMBER AS IDENTIFIER 46

CHECK THE AEOS EVENT LOG 47

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 35/48

1. Introduction

This manual describes how you can use AEOS Blue together with Nedap's long range vehicle

identification products:

•TRANSIT

TRANSIT is Nedap's platform for automatic identification of vehicles and drivers. TRANSIT is

specifically designed to perform in high security applications and under harsh environmental

conditions, offering long-range identification of taxis, ambulances, buses and trucks.

•uPASS

uPASS is Nedap's vehicle and people identification platform based on UHF RFID technology.

Specifically designed for convenient yet secure access control in every parking facility, gated

community and campus.

•ANPR Access / ANPR LUMO

ANPR is Nedap's automatic number plate recognition (ANPR) platform. Designed for vehicle

access applications where it is not possible or desired to issue RFID tags. ANPR is the perfect

solution for situations where vehicles need to be granted access temporarily or incidentally.

This manual shows you how Nedap vehicle identification hardware must be connected to the

AEOS Blue controller. It also provides step-by-step instructions to configure the hardware, as well

as AEmon and AEOS.

For more information on Nedap's long range vehicle identification products, go to

https://www.nedapidentification.com/products/

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 36/48

2. TRANSIT Ultimate (for Wiegand)

2.1 Connection overview

AP7803

TRANSIT

Wiegand

D0 O-2 (GREEN)

D1 O-3 (WHITE)

Vreader

GND GND (BLACK)

Vout

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 37/48

2.2 Configuring the TRANSIT reader (for Wiegand)

All tags for the TRANSIT reader, both the normal and the ultimate tag, are encoded with a specific

Nedap customer code. You must use the same customer code for the TRANSIT reader. Specific

firmware is required, depending on the type of interface you use to connect the reader to the

AEOS Blue controller. The default interface is the Wiegand interface and the firmware that should

be used for this connection type is P81.

To configure the TRANSIT reader, take the following steps:

Update the TRANSIT reader firmware (if necessary)

By default, the TRANSIT reader is configured with the correct end user customer code. If the

settings need to be changed, you must upload the P81 firmware with the correct customer code to

the reader. For this, you need a dedicated Nedap Firmware Upgrade software tool. Nedap

Identification Systems can provide you with the correct firmware and tools.

The example below shows a firmware upload with (in this case, for example) customer

code DF1814.

Uploading P81 firmware with the Nedap Firmware Upgrade software tool

1. Log in to the Nedap Identification Systems partner portal

2. Download and install the PICLoader software.

3. Connect the Transit reader to the computer.

4. Open the PICLoader software tool.

5. Click the 'open folder' icon and select the correct TRANSIT firmware.

6. Click Download.

7. Close the PICLoader software tool.

Step

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 38/48

Test the communication

1. Download and install the P81Test software.

2. Open the P81Test software tool.

3. Select the correct communication port and click Connect.

4. Press F3 and configure the reader. Select the correct Wiegand protocol and configure

other options such as the relay hold time, repeat time and facility code. Click OK.

5. Close the P81 Test software tool.

Configuring reader options with the P81Test software tool

The customer code settings must match the settings in AEOS, see section 2.4.

Step

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 39/48

Adjust the dip switch

1. To send the tag number as Wiegand 26 format, set the dip switch as shown below.

For other Wiegand formats, please refer to the P81 firmware guide.

2.3 Configuring AEmon (for Wiegand)

To configure the AEOS Blue controller for the TRANSIT reader (Wiegand interface) in AEmon, take

the following steps:

Configure the identifier type in AEmon

1. Start AEmon

2. In AEmon, create/open the configuration, including the AP7803 AEOS Blue controller and

the StandardDoor access point (see the AEOS Access Points and Entrances manual).

3. Right-click the StandardDoor AEbc, and click Properties.

Step

Installation and Configuration | AEOS Blue and vehicle identification EN

Manual version 310/48

4. Open the Identifier type editor and select Generic.

5. For Wiegand 26: Set the Format to Binary and select Numeric.

6. Check the other settings for the Wiegand 26 interface, see the example below..

Wiegand 26 identifier type settings

For other Wiegand formats, other settings may apply, like the example on the next page.

The identifier type settings must match the settings in AEOS, see section 2.4.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Nedap Controller Handbücher

Nedap

Nedap Smart Deactivator Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung