Nedap Prox-Booster Bedienungsanleitung

BOOSTERS

USER'S GUIDE

PROX-BOOSTER

SMARTCARD-BOOSTER

TRANSITION-BOOSTER

2007-04-02

This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication

conveys no license under any patent or other right, nor does the publisher assume liability for any consequence of its

use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be

reproduced in any way, in whole or in part, without the written consent of the publisher.

BOOSTERS

CONTENTS

CONTENTS.................................................................................................................................................. 2

1INTRODUCTION .................................................................................................................................. 3

2INSTALLATION .................................................................................................................................... 4

2.1 DIMENSIONS............................................................................................................................. 4

2.2 TEMPERATURE CONSIDERATIONS....................................................................................... 4

2.3 SOLAR CONTROL WINDSHIELDS........................................................................................... 4

3SMARTCARD CONFIGURATION........................................................................................................ 5

3.1 CONFIGURATION PROCEDURE ............................................................................................. 5

3.2 HOW TO CREATE A CONFIGURATION CARD ....................................................................... 5

3.2.1 TARGET DEVICE.......................................................................................................... 6

3.2.2 CREATION PROCEDURE ............................................................................................ 6

3.2.3 DEFAULT CONFIGURATION ....................................................................................... 9

3.3 PROGRAM THE CONFIGURATION CARD ............................................................................ 10

3.3.1 USING THE PHILIPS PEGODA PROGRAMMER ...................................................... 10

3.3.2 USING ANOTHER MIFARE PROGRAMMER ............................................................ 11

3.4 TESTING THE CONFIGURATION .......................................................................................... 12

3.5 CONFIGURATION FILES ........................................................................................................ 12

4MTR CONFIGURATION..................................................................................................................... 13

5IDENTIFYING THE BOOSTER WITH A TRANSIT............................................................................ 14

5.1 HOW TO USE THE BOOSTER ............................................................................................... 14

5.2 READER OUTPUT...................................................................................................................14

6BUZZER INDICATIONS ..................................................................................................................... 15

7BATTERY REPLACEMENT ............................................................................................................... 15

ATECHNICAL SPECIFICATIONS ........................................................................................................16

BPART NUMBERS ............................................................................................................................... 16

BOOSTERS

1 INTRODUCTION

The Prox-Booster, Smartcard-Booster and Transition-Booster are active dual ID tags enabling

simultaneous identification of the inserted personal ID card and the embedded vehicle ID resulting in

rapid driver and vehicle monitoring.

A Proximity or Smartcard can be placed in the Booster unit. Additionally a separate ID (representing

vehicle ID) is programmed in the Booster’s hardware. Once configured, the Booster allows a driver ID

badge and embedded vehicle ID to be read from a distance up to 10 meters (33 feet) in combination with

NEDAP TRANSIT readers. This solution substantially enhances the level of security when controlling

activities of vehicles that are regularly used by different drivers. Additionally a fully integrated vehicle and

personnel access solution can be implemented.

For more details about the NEDAP TRANSIT reader refer to the TRANSIT installation guide.

The combined vehicle and driver ID is a unique NEDAP patented feature. Optionally the vehicle-ID can

be sacrificed if more information from the personal ID card is required.

The following personal ID card types are identified with the Boosters.

•Prox-Booster NEDAP, EM and HID PROX

•Smartcard-Booster MIFARE, HID iCLASS, ISO14443A and ISO15693

•Transition-Booster all of the above

This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.

Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

BOOSTERS

2 INSTALLATION

2.1 DIMENSIONS

The Boosters are easily mounted to the inside of the car’s windshield by means of suction cups. Users

should ensure the visual contact between the Booster and any TRANSIT reader is unobstructed with

items such as stickers or metallized windshields (see also chapter 2.3 about solar control windshields).

Note that the Booster's suction cups must be faced toward the reader to achieve maximum reading

distance.

Dimension millimeters inches

Overall length X 116 4.57

Overall width Y 72 2.83

Overall height Z 31 1.22

Body height Z1 26 1.02

Booster Dimensions

2.2 TEMPERATURE CONSIDERATIONS

The Booster is designed to operate within the extreme temperature ranges, which often occur behind a

vehicle’s windshield during the winter or summer seasons (-20°C to 85°C / -4°F to +185°F). However the

personal identification card inserted in the Booster may not be designed to withstand such temperatures

and could suffer damage as a result.

Nedap advises to remove the personal identification card when not in use.

CAUTION: DO NOT LEAVE CARD IN ACCESS DEVICE WHEN LEAVING THE VEHICLE, AS THIS

PRESENTS A SECURITY RISK.

CAUTION: DO NOT LEAVE CARD IN ACCESS DEVICE FOR LONG PERIODS OF TIME IN EXTREME

HEAT, AS THIS MAY DAMAGE THE CARD.

2.3 SOLAR CONTROL WINDSHIELDS

From 1997 onwards several car manufacturers introduced vehicles with solar control windshields. The

solar control windshields are equipped with a metalized coating, which can block the TRANSIT signal

from the Booster mounted on the inside of the windshield of the vehicle.

Most of these windshields have a metal free zone where transponders can be mounted. The metal free

zone of metalized windshields is most often found in the middle of the windshield behind and slightly

below the rear view mirror. In vehicles manufactured after 1998 the metal free zone should be indicated

on the window.

We advise the owner to contact the local car dealer if it is not clear where the aperture is exactly

positioned in a certain vehicle and where the transponder should be mounted.

BOOSTERS

3 SMARTCARD CONFIGURATION

The Smartcard-Booster and the Transition-Booster can be configured by means of a configuration card.

This configuration card is a Mifare Classic 1K or 4K card that is programmed with the configuration

settings.

Configuration is only required if the factory default settings are not sufficient. The default settings are

described in chapter 3.2.3.

3.1 CONFIGURATION PROCEDURE

Every Booster used in the application should be configured with the configuration card. The simple

configuration procedure is described below.

Insert the configuration card in the Booster and push the button. The Booster sounds the buzzer with an

increasing frequency (♪♪♪) to indicate that the configuration settings have been accepted.n

3.2 HOW TO CREATE A CONFIGURATION CARD

NEDAP has developed a software application that allows system integrators to create configuration

cards. This software can be downloaded from our website www.nedapavi.com.

Smartcard-Booster Config software

nSee chapter 6 for details about the buzzer indications.

BOOSTERS

3.2.1 TARGET DEVICE

The Booster Configuration software can be used to configure a number of different devices. The user-

interface is adapted to the selected target device. Select in the ‘Target’ menu which device you are about

to configure.

Smartcard Booster

;Transition Booster

Prox Booster EM4x50 not explained in this manual

Multi-Technology Reader Module see chapter 4

3.2.2 CREATION PROCEDURE

Follow the procedure below to create a configuration card with application specific settings.

1. Specify OPERATING MODE (see chapter 3.2.2.1)

2. Specify FRAME LENGTH (see chapter 3.2.2.2)

3. Specify HIGH FREQUENCY settings (see chapter 3.2.2.3)

4. Specify LOW FREQUECY settings (only for Transition-Booster) (see chapter 3.2.2.6)

5. Save the configuration settings into a file.

6. Write the configuration into a blank Mifare Classic 1K or 4K card.

3.2.2.1 OPERATING MODE

Booster (only Driver-ID)

Up to 16 bytes of data from the personal identification card is read. The Vehicle-ID is omitted.

Combi-Booster (Vehicle-ID + Driver-ID)

Vehicle-ID combined with up to 11 bytes from the personal identification card is read.

Tacho-Booster (Vehicle-ID + Driver-ID + Tacho-Counter)

Vehicle-ID and Driver-ID combined with Tacho-Counter value. If this option is selected than

automatically extended-length is selected.

3.2.2.2 FRAME LENGTH

This affects the length of the message sent from Booster to TRANSIT reader.

Extended length (longer Driver-ID)

Select extended-length in order to support all transponder types and maximum amount of data.

The extended-length may be not compatible with older firmware versions in the TRANSIT reader.

You might need to upload new firmware into the reader.

The identification speed is a bit slower compared to applying standard-length.

Standard length (backwards compatible, faster identification)

Select standard-length in applications where the Boosters must be compatible with older types of

transponders or where fast identification is important.

Please note that when reading low-frequency cards with a Transition-Booster this setting is not used.

For NEDAP and EM cards the extended-length is not required and therefore the Booster will

automatically use standard-length (even if extended-length is selected in the configuration).

For HID PROX the extended-length is required so extended-length is used automatically if such a card is

identified (even if standard-length is selected in the configuration).

BOOSTERS

3.2.2.3 HIGH FREQUENCY

Enable HID iCLASS CSN

Enable or disable the reading of HID iCLASS transponders. Only the card serial number can be

read from these transponders.

Enable ISO14443-A / MIFARE

Enable or disable the reading of ISO14443-A / Mifare transponders.

Data to read from ISO14443-A / MIFARE

For ISO14443-A cards only the card serial number can be read. The cascaded card serial number

(e.g. used in Mifare UltraLight cards) is also supported. For MIFARE cards also other information

from the card can be read. Select one of the following choices:

;ISO14443-A card serial number

MIFARE UltraLight data (see chapter 3.2.2.4 for more details)

MIFARE Classic data from sector (see chapter 3.2.2.5 for more details)

Enable ISO15693 / LEGIC CSN

Enable or disable the reading of ISO15693 / LEGIC Advant transponders. Only card serial number

can be read from these transponders.

3.2.2.4 READING MIFARE ULTRALIGHT DATA

The Mifare UltraLight transponders’ 512 bit EEPROM memory is organized in 16 pages with 4 bytes

each.

Page Number

Page number to start reading from (in range from 0 .. 15).

Data Length

Number of bytes to read. The reading will wrap around to page number 0 if additional bytes after

page 15 should be read. The maximum number of bytes to read is 16.

Data Offset

Number of bytes to skip reading (in range from 0 .. 8).

Example:

Data to read: MIFARE UltraLight data

Page Number: 4

Data Length: 4

Data Offset: 2

The settings above will read the data below shown in blue.

Byte 0 Byte 1 Byte 2 Byte 3

Page 3 not read not read not read not read

Page 4 skipped skipped DATA DATA

Page 5 DATA DATA ignored ignored

Page 6 not read not read not read not read

BOOSTERS

3.2.2.5 READING MIFARE CLASSIC DATA

The Mifare Classic 1K and 4K cards are fully supported. Also other Mifare transponders which are

compatible (such as Mifare DESfire and SmartMX) can be used. The memory is organized in sectors with

blocks. Every block consists of 16 bytes. Only data from one block can be read.

Sector Number

Sector number to read data from (in range from 0 .. 39).

Block Number

Block number to read data from. The block number must be in range from 0 .. 3 for the first 32

sectors. For the sectors 32 .. 39 the block number can range from 0 .. 15.

Data Length

Number of bytes to read. The reading will wrap around to page number 0 if additional bytes after

page 15 should be read. The maximum number of bytes to read is 16.

Data Offset

Number of bytes to skip reading.

Read Key

Key A or Key B can be used to authenticate to the transponder.

Select which key to use and the key itself.

Example:

Data to read: MIFARE Classic data from sector

Sector Number: 2

Block Number: 1

Data Length: 8

Data Offset: 4

The settings above will read the data below shown in blue.

Sector Block 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

0 x x x x x x x x x x x x x x x x

1 x x x x D D D D D D D D x x x x

2 x x x x x x x x x x x x x x x x

3 x x x x x x x x x x x x x x x x

3.2.2.6 LOW FREQUENCY

The low frequency settings are only applicable for the Transition-Booster.

Enable NEDAP PM

Enable or disable the reading of NEDAP PM transponders. NEDAP PM cards are always

transmitted to the TRANSIT reading using standard-length. See chapter 3.2.2.2.

Enable EM4102 or compatible

Enable or disable the reading of EM4102 and compatible transponders. EM4102 cards are always

transmitted to the TRANSIT reading using standard-length. See chapter 3.2.2.2.

Enable HID PROX

Enable or disable the reading of HID PROX transponders. HID PROX cards are always transmitted

to the TRANSIT reading using extended-length. See chapter 3.2.2.2.

BOOSTERS

3.2.3 DEFAULT CONFIGURATION

In the table below the factory default configuration is shown.

Configuration settings Default value

Operating mode Combi-Booster (Vehicle-ID + Driver-ID)

Frame length Extended-length (longer Driver-ID)

Enable HID iCLASS CSN Yes

Enable ISO14443-A / MIFARE Yes, ISO14443-A card serial number

Enable ISO15693 / LEGIC Advant CSN Yes

Enable NEDAP PM Yes

Enable EM4102 or compatible Yes

Enable HID PROX Yes

Please use the table below to fill-in your application specific settings.

Configuration settings Value

Operating mode

Frame length

Enable HID iCLASS CSN

Enable ISO14443-A / MIFARE

Data to read

Sector number

Block number

Data length

Data offset

Read key A or B

Enable ISO15693 / LEGIC Advant CSN

Enable NEDAP PM

Enable EM4102 or compatible

Enable HID PROX

BOOSTERS

3.3 PROGRAM THE CONFIGURATION CARD

3.3.1 USING THE PHILIPS PEGODA PROGRAMMER

3.3.1.1 REQUIREMENTS

This requires a Philips Pegoda Mifare programmer to be connected to a USB port on

your computer. In the ‘Pegoda’ menu of the configuration software click ‘Connect’ to

connect to the programmer.

Once the connection has been established and all configuration settings are entered,

place an empty Mifare Classic 1K or 4K transponder card on the Pegoda unit.

3.3.1.2 PROGRAMMING

To program the configuration into the Mifare card click ‘Write configuration into card’ in the ‘Pegoda’

menu. The message ‘Configuration written into mifare card’ should appear to indicate that the

programming action was successful.

The software will warn you with the message ‘Overwrite configuration card’ if there is already a

configuration on the Mifare card. Click ‘Yes’ to proceed and overwrite the configuration on the card or

click ‘No’ to abort.

3.3.1.3 READ BACK

It is also possible to read back what configuration is programmed into a configuration card. Click ‘Read

configuration from card’ in the ‘Pegoda’ menu to do that.

Inhaltsverzeichnis

Andere Nedap Extender Handbücher

Nedap

Nedap VP1002 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung