Nemo DSS-220200 Bedienungsanleitung
0
0
Functional Description and Specifications
Intended Use
The Nemo V2 Divers Drill can be used underwater, in wet
conditions, and on dry land. This tool is a valuable asset to any
professional who works in and around water.
Packing List
Your Nemo V2 Divers Drill is packaged together with the following
accessories:
♦2 Spare chucks and 3 extra chuck screws
♦Two rechargeable 6 Ah Lithium-ion (Li-ion) battery packs
♦Battery charger
♦Carrying case
♦Hand pump
♦Drying cloth
Technical Specifications
Battery Charger
Model
DSS-220200
Approximate charging time
55 minutes
Charging output voltage
21V
Charging input voltage
100V – 240V
1
Nemo V2 Divers Drill
Model
DDV2-18-3Li-50
Battery pack voltage
18V Li-ion
Battery cell specification
3Ah / 6Ah
No load speed (two speeds)
0 – 400 / 0 – 1500 RPM
Maximum torque
345 in-lbs ( 39 N-m )
Chuck size
½ in ( 13mm )
Net weight (with battery)
6.39 lbs ( 2.9kg )
Working temperature
32-140°F ( 0-60°C )
Submersible up to
164 ft ( 50m )
Caution: You must pressurize the drill before you can use
it underwater, as described in Pressurizing the Drill for
Underwater Use, page 11 .
2
Safety Warnings
Warning: Read all safety warnings and instructions, and
save them for future reference. Failure to adhere to
these warnings can result in serious injury and damage
to equipment.
Work Area Safety
♦All work should be done in accordance with the local, state,
and government occupational safety and health guidelines.
♦Keep your work area clean and well lit.
♦Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases, or dust.
♦Keep bystanders away when operating power tools.
Personal Safety
♦Stay alert and use common sense when operating power tools.
Do not use power tools when you are tired or under the
influence of drugs, alcohol, or medication.
♦Use personal protective equipment. It is recommended to
always wear eye protection, as well as a P2 filter-class
respirator.
♦Dust from materials such as lead-containing coating, some
wood types, minerals, and metal can be harmful to one’s
health. Observe the relevant regulations in your country for the
materials to be worked.
3
Power Tool Safety
♦Store idle power tools out of reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool.
♦Maintain your power tools. Check for misalignment or binding
of moving parts, breakage of parts, and any other condition
that may affect the power tool’s operation. If damaged, have
the power tool repaired by an authorized service technician.
Caution: Under no circumstances should the power tool
be opened for repairs or any other purpose by anyone
other than an after-sales service technician authorized
by Nemo Power Tools. Opening the power tool
invalidates the manufacturer warranty.
♦Use power tools, accessories, and tool bits in accordance with
these instructions and in the manner intended for the
particular type of power tool, taking into account the working
conditions and the work to be performed. Consult local, state,
and government occupational safety and health guidelines
before operating a power tool.
♦Switch off the power immediately if the tool bit jams. Be
prepared for high reaction torque that can cause kickback. The
tool bit can jam when the power tool is subject to overload, or
if it becomes wedged in the workpiece.
♦Hold the power tool with a firm grip. High reaction torque can
briefly occur while driving in and loosening screws.
♦Work only on secured, stable items. Do not hold any item to be
worked on by the power tool in your hand. Secure the
workpiece, clamped with clamping devices or in a vice, to
ensure safety.
♦Always wait until the power tool has come to a complete stop
before placing it down. The tool bit can jam and lead to loss of
control over the power tool.
4
Rechargeable Battery Safety
♦Use only the battery pack supplied with your power tool.
♦When the battery pack is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails, and screws,
which can make a connection from one terminal to another.
♦Store the battery pack only within a temperature range of 32˚F
- 113˚F ( 0°C-45°C ).
♦Before any work on the power tool, such as a tool change, as
well as during transportation and storage, remove the battery
pack from the power tool. There is danger of injury when
accidentally activating the On/Off trigger.
♦Do not open the battery.
♦Protect the battery against heat, including continuous sun
irradiation and fire.
♦When the battery is defective, liquid can escape and come into
contact with adjacent components.
♦Use only original batteries with the voltage listed on the
nameplate of your power tool. When using other batteries,
such as imitations, reconditioned batteries, or other brands,
there is danger of injury as well as property damage through
exploding batteries.
♦Use only the battery charger provided with the power tool to
recharge the batteries. Only this battery charger is matched to
the lithium-ion (Li-ion) battery of your power tool.
♦Protect the battery charger from rain and moisture. The battery
charger is not waterproof.
♦Do not charge other batteries. The battery charger is suitable
only for charging the battery pack supplied with the tool.
♦Before use, always check the battery charger, cable, and plug. If
defects are detected, do not use the battery charger. Never
open the battery charger. Instead, have it opened and repaired
only by qualified personnel who will use original spare parts.
5
Getting Started with the Drill
Your V2 Nemo Divers Drill (DDV2-18-3Li-50) includes the following
main components:
6
Charging the Battery
The Li-ion batteries are supplied partially charged, and must be
charged to full capacity using the battery charger provided with the
drill before using the drill for the first time.
Caution: Only use the battery charger provided with
the drill. Only this battery charger is matched to the
Li-ion batteries supplied with your power tool.
Danger: Ensure that the voltage of the power supply
corresponds with the data given on the nameplate of
the battery charger.
Danger: Only use the charger in a dry environment. The
charger is not waterproof. Never attempt to charge the
battery under water.
A battery can be charged at any time without reducing its service
life. This is because the battery charger detects the charging
condition of the battery, and charges it with the optimum current
according to its temperature and voltage. This lengthens the
battery life and leaves it fully charged when stored in the charger.
Interrupting the charging procedure does not damage the battery.
1. Connect the mains plug of the battery charger to an electrical
outlet. A steady green light on the battery charger indicates
that the charger is ready for operation.
2. Press the battery charger’s CHOGORI connector into the socket
on the top of the battery pack. There is only one way to insert
the CHOGORI connector into the battery socket.
7
The battery begins charging as soon as it is connected to the
charger.
⬥A steady red light on the battery charger indicates that
the battery is charging.
⬥A steady green light on the battery charger indicates that
the battery is fully charged.
Note: The battery is equipped with an NTC temperature
controller that only allows it to be charged when its
temperature is between 32˚ F - 113˚ F ( 0°C-45°C ),
ensuring a long battery service life.
3. When you are ready to use the battery, rotate the CHOGORI
connector’s plastic cap counterclockwise and pull it vertically
out of the charger.
Inserting a Battery into the Drill
1. Set the rotational direction switch to the middle position.
Caution: To minimize the risk of accidental activation,
always ensure the rotational direction switch is in the
neutral (middle) position before performing any
maintenance work on the drill, as well as during
transportation and storage.
2. Insert the battery into the bottom of the drill base.
Caution: Use only a Li-ion battery from the original
factory with the voltage listed on the nameplate of your
drill. Using other batteries not suitable for the drill can
lead to malfunctions, cause damage to the power tool,
and pose a fire hazard.
3. Push the battery up until it is pushed to the limit, then rotate
the locking ring until it is securely locked. The locking ring holds
the battery pack in position and prevents it from detaching.
8
Inhaltsverzeichnis
Andere Nemo Bohren Handbücher
