Neptronic TM000 Bedienungsanleitung

Actuators

Specification & Installation Instructions

TM-RM-210819 1

Technical Data

TM000

TM020

TM060

TM080

RM000

RM020

RM060

RM080

Power supply

28 to 32 Vdc or 22 to 26 Vac

Power consumption

8 VA

30 VA Peak, 8VA

10 VA

30 VA Peak, 10VA

Torque

180 in.lb. [20 Nm] at rated voltage

360 in.lb. [40 Nm] at rated voltage

Running time through 90º

60 to 85 sec torque dependant

Fail safe - Enerdrive

Yes

Feedback

4 to 20 mA or 2 to 10 Vdc adjustable

Auxiliary switches

Yes (2)

Electrical connection

18 AWG [0.8 mm2] minimum

Inlet bushing

2 inlet bushing of 7/8 in [22.2 mm]

Control signal

Analog, Digital or Pulse with modulation (PWM) programmable (factory set with Analog control signal)

Angle of rotation

0 to 90 degrees, electronically adjustable (factory set with 90º stroke)

Direction of rotation

Reversible, Clockwise (CW) or Counterclockwise (CCW) (factory set with CW direction)

Operating temperature

0ºF to 122ºF [-18º C to 50ºC]

Storage temperature

-22ºF to 122ºF [-30º C to 50ºC]

Relative Humidity

5 to 95 % non condensing

Weight

4.5 lbs. [2 kg]

7 lbs. [3.2 kg]

Warning: Do not press the clutch when actuator is powered

Dimensions

Dimension

Imperial (in)

Metric (mm)

5.20

132.1

1.33

33.8

9.13

231.9

3.55

90.2

Caution

We strongly recommend that all Neptronic®products be wired to a separate transformer and that transformer shall service only Neptronic®products. This precaution will

prevent interference with, and/or possible damage to incompatible equipment.

When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.

Enerdrive System U.S.A. Patent #5,278,454

Features:

•Clutch for manual adjustments

•Maintenance free

•Position indicator

•Control signal fully programmable

•Fail safe by Enerdrive System 1

(on model 060 & 080)

•Auxiliary switches

(on model 020 & 080)

TM000

TM020

TM060

TM080

RM000

RM020

RM060

RM080

Actuators

Specification & Installation Instructions

Mechanical installation

1. Manually close the damper blades and positioned the

actuator at 0º or 90º.

2. Slide the actuator onto the shaft.

3. Tighten the nuts on the “U” bolt to the shaft with a 10mm

wrench to a torque of 150 in.lb. [17 Nm].

4. Slide the mounting bracket under the actuator. Ensure free

movement of the slot at the base of the actuator. The bracket

pin must be placed in the mid distance of the slot.

5. Fix the bracket to the ductwork with #8 self-tapping screws.

Wiring Diagrams

Analog

1For 4 to 20mA control signal set dipswitch #3 ON.

2For 2 to 10 Vdc control signal set dipswitch #4 ON.

PWM

Digital –3 wire / 2 position

Digital –4 wire / 3 point floating

Special consideration for digital control

In this mode, the actuator is sensitive to induced electrical voltages from external sources. To prevent such interference, if the signal on pin 3 on TB1

is from an external 24 Vac source, install a resistor 2.2kohm, 0.5W between pins 3 and 1 of TB1. This resistor is included.

DIP SWITCH #3 MUST BE OFF IN DIGITAL MODE

For 2 to 10 Vdc input

For analog wiring, set dipswitch #3 OFF.

For 2 to 10 Vdc output feedback

For any of above wiring configurations, set dipswitch #4 ON.

For 4-20 mA analog input

For analog wiring, set dipswitch #3 ON.

For 4-20 mA output feedback

For any of above wiring configurations, set dipswitch #4 OFF.

1 2 3 4 5

2 to 10 Vdc1

COMMON (-) FEEDBACK

4 to 20 mA2

TB1

24 Vac or 30 Vdc (+)

1 2 3 4 5

SUPPLY (+) PWM

CONTROL SIGNAL

COMMON (-) FEEDBACK

4 to 20 mA

24 Vac (+)

2.2 K

1 2 3 4 5

FEEDBACK

4 to 20 mA

DRIVE CCW

TB1

COMMON (-)

DRIVE CW

2.2 K

1 2 3 4 5

FEEDBACK

4 to 20 mA

DRIVE CCW

COMMON (-)

24 VAC (+)

TB1

DRIVE CW

Actuators

Specification & Installation Instructions

1 2 3 4

Rotation: CCW

Input in mA Feedback in Vdc

Fail safe return at 90º

1 2 3 4

Rotation: CW

Input in Vdc Feedback in mA

Fail safe return at 0º

PC Board

Dip switch settings

Factory default

Stroke adjustment –No control signal change

1. Apply power and, WAIT FOR LED TO BE OFF (around 10 seconds).

2. Press and release the reset button to start the auto-stroke process.

The LED should be illuminated.

•First option:

The actuator will then travel in both directions to find its limit and position itself according to the demand.

The LED will extinguish, the process is complete.

•Second option:

When the desired start position is reached, press and release the reset button. The actuator will now go the end

position. (you can also press and release the reset button when It's reaches the end position)

The LED will extinguish, the process is complete.

Programming –Change of control signal

1. Remove power and put all dip switches "OFF". (factory preset).

2. Apply power and, within 10 seconds, press and release the reset button. The LED should be blinking.

3. Select the control signal with dip switches:

•Digital (On/Off or 3 point floating)

move switch No1 "ON” and then “OFF”.

•Analog (factory preset)

move switch No2 "ON” and then “OFF”.

Stroke adjustment

see the stroke adjustment section above.

Note, If PWM mode is selected:

•Time base: When programming is done,

if switch No3 is "on" time base is 0.1 to 5 sec. (resolution 20 msec.)

if switch No3 is "off" time base is 0.1 to 25 sec. (resolution 100 msec.)

* For 5 sec. time base, we strongly recommend a switch common connection for better position stability.

•Switch 24 Vac: Triac or dry contact, 40mA maximum switching current.

•Switch common: NPN transistor, SCR, Triac or dry contact 75mA maximum switching current.

Potentiometer

Dip switch

Reset button LED

Terminal

Clutch

1 2 3 4 5

TB1

1 2 3 4

DS1

Actuators

Specification & Installation Instructions

Feedback selection (CCW direction)

To select CCW direction put switch No1 "ON".

In Analog or 3 point floating mode you can program the feedback control.

If switch No3 is "OFF":

The feedback control is automatically reverse to 4 to 20 mA for 90

to 0 degrees.

0º

20 mA 90º

4 mA

If switch No3 is "ON":

The feedback control is to 20 to 4 mA for 90 to 0 degrees.

0º

4 mA 90º

20 mA

Zero and span calibration

This feature is applicable to analog control signal only.

1. Remove power and put all dip switches "OFF". (factory preset).

2. Apply power and, within 10 seconds press and hold the reset button until the LED blinks once.

The Zero and span calibration process then start.

3. Release the reset button. The LED is now constantly illuminated.

4. Apply new minimum voltage.

It can be any value between 0 to 7 Vdc, with an external 0 to 10 volt supply (ex: MEP).

5. Press and release the reset button to memorize the new minimum voltage. The LED blinks.

6. Apply new maximum voltage.

It can be any value between 3 to 10 Vdc, this value should be greater than the new minimum value.

7. Press and release the reset button to memorize the new maximum voltage. The LED blinks.

The Zero and span calibration process is complete.

Note: To reset zero and span to 2 to 10 Vdc (factory value). You just have to re-select the analog control signal mode, see

Programming.

Wiring Diagrams for auxiliary switches

Auxiliary switch rating:

5 Amp resistive, 250 Vac

BLACK

RED

GREEN

BROWN

WHITE

BLUE

LOWER COMMON

LOWER CLOSED 10-90º

LOWER CLOSED 0-10º

UPPER COMMON

UPPER CLOSED 0-80º

UPPER CLOSED 80-90º

Dieses Handbuch passt für folgende Modelle

Andere Neptronic Controller Handbücher

Neptronic

Neptronic BT000S Bedienungsanleitung

Neptronic

Neptronic TM000N Bedienungsanleitung

Neptronic

Neptronic EVCB Series Bedienungsanleitung

Neptronic

Neptronic TM200FN Bedienungsanleitung

Neptronic

Neptronic RM020FN Bedienungsanleitung

Neptronic

Neptronic AROB24T Bedienungsanleitung

Neptronic

Neptronic ST000S Bedienungsanleitung

Neptronic

Neptronic HRO20LSS Bedienungsanleitung

Neptronic

Neptronic BBT24A Bedienungsanleitung

Neptronic

Neptronic DTS Bedienungsanleitung

Neptronic

Neptronic ARO24T Bedienungsanleitung

Neptronic

Neptronic BT160 Bedienungsanleitung

Neptronic

Neptronic LT060X11 Bedienungsanleitung

Neptronic

Neptronic SPC Bedienungsanleitung

Neptronic

Neptronic TSUB00 Series Bedienungsanleitung

Neptronic

Neptronic BM000N Bedienungsanleitung

Neptronic

Neptronic BT000 Bedienungsanleitung

Neptronic

Neptronic TSU00 Series Bedienungsanleitung

Neptronic

Neptronic BM200S Bedienungsanleitung

Neptronic

Neptronic HRO20 Bedienungsanleitung

Neptronic

Neptronic TM200N Bedienungsanleitung

Neptronic

Neptronic BT060X4 Bedienungsanleitung

Neptronic

Neptronic BBTHV1100A Bedienungsanleitung

Neptronic

Neptronic TUCB Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung