Nertpow CH010 Bedienungsanleitung
INSTRUCTION MANUAL
Model No.: CH010
110-120V 1500W
ASSEMBLE & OPERATION INSTRUCTION
Please read carefully and Save this instruction for future
reference
Introduction
The infrared heater contains an gold halogen lamp formed reflector heating system that provides even heat distribution.
The infrared heater saves 30%-40% of electricity in comparison to traditional heaters. The infrared heater is commonly used
for outdoor heating.
Warning
READ CAREFULLY-The infrared heater is designed for safe operation. Nevertheless, installation,
maintenance and operation of the heater can be dangerous. Observing the following procedures
will reduce the risk of fire, electric shock, injury to person and keep installation time to a minimums.
Save these instructions for future use.
1. Read all instruction before using this heater.
2. Remove the unit from its packaging and check to make sureit is in good condition before using.
3. Do not let children play with parts of package (such as plastic bags).
4. Check the household voltage to ensure it matches the heater’s rated specification.
5. Check the power cord and plug carefully before use to make sure that they are not damaged.
6. Before unplugging the power cord, be sure to turn off the power. When powering on the device, make
sure your hands are dry to avoid electric shock.
7. Do not use flammable materials, such as furniture and pillows, near or pointing to the heater. Bedding, paper,
cloth, and curtains should be at least 3 feet (1 meter) in front of the heater, and always place them on the sides
and back.
8. Do not use the heater near bathtubs, swimming pools or any liquid source.
9. To protect against electric shock, do not immerse cord or plug in water or any other liquid.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening , as this may cause an
electric shock, fire or damage to the heater.
11. Be sure to unplug the heater when not in use.
12. Do not let the power cord hang on the table where it is easy to be pulled by
children.
13. Do not put fingers or foreign objects into the heater while in operation.
14. Do not leave the appliance unattended during use.
15.This heater is not intended for use in bathrooms, laundry and similar indoor locations, never located heater
where it may fall into a bathtub or other water container.
16.No liability can be accepted for any damage caused by non compliance with these instructions or any other
improper use or mishandling.
17. This appliance is not suitable for use by persons (including children) who have defects in physical, sensory or
mental abilities or lack experience and knowledge, unless the person responsible for their safety supervises or
instructs them on the use of the appliance. Children and vulnerable people should be supervised to ensure that
they do not play with the appliance.
18. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
19. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may
cause blockage. Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation.
20. The heater parts may exceed 200℃(392℉), and touch with the heating tube, reflector, or metal parts near
the heating tube may cause severe burns. To avoid burns, do not allow bare skin to touch hot surfaces.
21. ALWAYS allow heating element to cool at least 10 minutes before touching the heating tube or adjacent parts.
22. This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact
your local municipality for the nearest collection point.
WARNING: Hot Surface! Do Not Touch!
Introduction
The CH010 halogen heater produce instant and comfortable heat like the sun. These robust and weatherproof heaters are
designed for domestic and commercial heating applications at outdoor well-protected area.
Model
CH010
Voltage(V)
110-120V AC
Wattage(W)
1500W
Hertz(Hz)
60Hz
Dimensions W×H×D
62.5*10.5*7.0cm/ 24.6*4*2.7inch
Weight
1.7kg/ 3.7lb
This heater is for use on 120 volts. The cord has a plug as below. The green grounding lug extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot
grounded receptacle is available.
ASSEMBLY INSTRUCTIONS
Installation for wall mounted
* Pencil *Hammer *Level *Screw Driver *Power Drill and drill bits
BLUE/GREEN flashing means tip over function work. Heater with tip over function, make sure
the correct working angel in 45-80°.
The wall bracket is provided with the heater. The bracket is specially designed to install the
product on the wall or ceiling before drilling. The wall/ceiling bracket is sturdy and has no hidden
water pipes or wires. The heater must be installed at least 16 inches from the wall and at least 6
inches from the ground.
Caution: Always keep a distance of 400mm(1.5inch) from the wall to prevent
touching flammable objects such as curtains.
Important: Ensure that the supply cables is well mounted and won’t touch the
reflector of the heater or hot surface. The supply cable can be fixed to the metal
mounting bracket behind heater with plastic zip ties.
The heater must be installed at least 2.4M(7.8ft) above the floor. (Wall Mounted Installation)
Attention: Cable should not pass through the heater.
Attention: The heater can only be used horizontally.
Tripod Installation:
1.
Placing L-shaped bracket to stand 2. Securing L-shaped bracket to
stand with screw&nut
3.
Moving the slip panels to the
proper place
Accessories
Quantity
L shape bracket
2pcs
Screw & nut
1 set
M5*10mm screw
2pcs
4. Fix the L-shaped bracket on the sliding panel on the heater with screws M5*10mm. Before tightening the screws,
please align the correct position with the hole on the back of the heater.
Attention: This side is on the left
5. Make correct angel in 35-60°.
Note: Wrong installation working position could
cause tip over function work, heater indicator will
flash green/blue.
Note: When used outdoors, it is recommended to reinforce the tripod
with sandbags or other heavy objects to prevents the wind from falling over.
(The sandbags are not included in the package.)
REMOTE CONTROL INSTRUCTION OPERATING
Remote Function:
1. Turn ON/OFF the power
2. Operation: Press the button, then press the heat levels (L1-L2-standby - off)
3. Indicator color:
Red- Standby; Green-L1 750W; Blue-L2 1500W; Blue&Green flashing -Tip over function / Overheat protection
Button
Function
ON/OFF
Turns heater on or off
Ⅰ
Set the power level at 750W
Ⅱ
Set the power level at 1500W
Inhaltsverzeichnis
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung