Net Optics iBYPASS 40G Bedienungsanleitung
Quick Install Guide
800-0228-001 Rev A 11/13
I2BP-40
2
PLEASE READ THESE LEGAL NOTICES CAREFULLY.
By using the Net Optics iBypass 40G Switch, you agree to the terms and conditions of usage set forth by Net Optics, Inc.
No licenses, express or implied, are granted with respect to any of the technology described in this manual. Net Optics
retains all intellectual property rights associated with the technology described in this manual. This manual is intended
to assist with installing Net Optics products into your network.
Trademarks and Copyrights
©2013 by Net Optics, Inc. Net Optics is a registered trademark of Net Optics, Inc. iBypass is a trademark of Net Optics,
Inc. Additional company and product names may be trademarks or registered trademarks of the individual companies
and are respectfully acknowledged.
Additional Information
Net Optics, Inc. reserves the right to make changes in specications and other information contained in this document
without prior notice. Every effort has been made to ensure that the information in this document is accurate.
3
Contents
iBypass 40G Switch Content 4
iBypass 40G Switch Overview 5
Connect Power 8
Connect PC to Console Port 10
Congure the iBypass 40G IP 12
Connect to the Network 14
Connect Monitoring Tools 15
4
iBypass 40G Switch Content
This guide provides the initial steps to set up and congure the Net Optics iBypass
40G Switch.
Carefully unpack the contents and verify you have the following components:
• iBypass 40G Switch
• 3-meter RJ45, CAT 5e 4-pair
• RJ45 to DB9 Console Port to PC cable
• Long Ear Extender and Short Ear Extender for rack mounting
• Two External Power Supplies (12VDC, 9A, 108W)
• Eight Phillips screws
• iBypass 40G Switch Quick Install Guide (this document)
• iBypass 40G Switch User Guide (on CD)
• End User Agreement, Registration Card and Extended Warranty (if purchased)
The QSFP+ transceiver kits and 40G MTP cables are sold and shipped separately.
Contact Net Optics Technical Assurance Center if any component is missing or
damaged. Contact details are at the back of this guide.
5
iBypass 40G Switch Overview
2x16 Character Display
Network
Ports
Monitor
Ports
Bypass, Tap, Power
LEDs
Activity & Alarm
LEDs
Management
Port
Console
Port
Figure 1 - Front View
• Console Port (RJ45) and Management Port (RJ45)
• 2 x 40G Monitor Ports (uses QSFP+ transceivers )
• 2 x 40G Network Ports (MTP Connectors)
Figure 2 - Rear View
• Hot swapple fans and replaceable power module
6
Step 1
Rack Mount iBypass 40G Switch
Install the iBypass 40G Switch into a standard 19-inch equipment rack. The switch is
designed to occupy one rack unit. Do the following to install the iBypass 40G Switch
into an equipment rack:
1. Remove the Ear Extenders and screws from the shipping bag.
2. Attach the Long Ear Extender to the switch if you are only mounting one switch
or attach the Short Ear Extender between two switches if you are mounting two
switches. See Figure 3.
3. Slide the switches in place in the rack.
4. Fasten the switches in place at the front panel ears using the Phillips screws.
5. Make sure the rack is properly electrically grounded.
Grounding
Ground the chassis to the rack by connecting a 14 AWG minimum ground wire with a
#8 ring lug to the ground connection on the rear of the chassis. Terminate the other
end of the ground wire to the rack ground bus bar.
7
Long Ear Extender
for one switch
Short Ear Extender
binds two switches
Figure 3 - Use Ear Extenders in Rack Mount Preparation
8
Step 2
Connect Power
Ensure the iBypass 40G Switch is grounded before connecting power. Do the
following to connect and apply power to the iBypass 40G Switch:
1. Plug one of the supplied power cords to a power connector located at the rear
of the chassis. Plug the other end to a power source. See Figure 4.
2. For redundancy, plug the other power cord to the iBypass 40G. Plug the other
end to a source independent from the rst power source.
The Power LEDs on the front illuminate.
Switch Default Settings
The iBypass 40G Switch ships with the following default system settings:
IP Address: 10.60.4.180 Threshold Port A: 80%
Netmask: 255.0.0.0 Threshold Port B: 80%
Gateway: 10.0.0.1 Username: admin
Password: netoptics
9
Figure 4 - Power Connections
10
Step 3
Connect Options
You have two ways of logging in to the iBypass 40G switch.
Option 1 - Connect PC to Management Port
1. Connect a PC whose IP address is on the same subnet as the iBypass switch.
The default address on the switch is:
IP Address: 10.60.4.180 Mask - 255.0.0.0 Gateway - 10.0.0.1
2. Connect a Cat 5e cable from your PC’s Ethernet port to the iBypass
Management port. See Figure 5.
3. Open a terminal window on the PC and ping 10.60.4.180 to conrm the
connection.
4. After you have conrmed that you have a connection, you can log in via SSH at
the terminal prompt, or enter the default address into the browser URL. Go to
the Assign IP in Web UI section if you want to log in through the Web UI. Go
to the next step if you want to log in to the CLI.
5. At the terminal window prompt, type ssh [email protected]. Enter
password netoptics. The Net Optics prompt appears.
6. At the prompt, enter admin for the user and netoptics for the password.
7. Change the password for the admin account by entering the following
command at the prompt:
modify user password admin <new_passwd> <re-enter_passwd>
where <new_passwd> is the new password for the admin account and
Inhaltsverzeichnis
Andere Net Optics Schalten Handbücher
Net Optics
Net Optics iMatrix ISW-CU3-S4x16 Bedienungsanleitung
Net Optics
Net Optics Director Bedienungsanleitung
Net Optics
Net Optics IBPO-HBSR-XFP Bedienungsanleitung
Net Optics
Net Optics BPO-HBSX-LC Bedienungsanleitung
Net Optics
Net Optics Director xStream Pro Bedienungsanleitung
Net Optics
Net Optics N-IDP-POBPSX-001, N-IDP-POBPLX Bedienungsanleitung
Net Optics
Net Optics PA-CU-AR Bedienungsanleitung
Net Optics
Net Optics 10/100/1000 Bedienungsanleitung
Net Optics
Net Optics 10/100/1000 Bedienungsanleitung
Net Optics
Net Optics Director Bedienungsanleitung
