NetBurner SB72 Bedienungsanleitung

SB72 User's Manual, 350030-006

e t B u r n e r

SB72 User's Manual

Revision 1.6

November 13, 2007

SB72 User's Manual, 350030-006 Pa e 2

Table of Contents

Table of Contents ............................................................................................................... 2

Overview ............................................................................................................................. 3

Configuration ..................................................................................................................... 3

Hardware Configuration........................................................................................................... 3

Hardware Configuration Examples ......................................................................................... 5

RS-232.................................................................................................................................................... 5

RS-485.................................................................................................................................................... 5

Networ Configuration ............................................................................................................. 6

Operational Configuration........................................................................................................ 7

Device Networ Settings ...................................................................................................................... 7

Device Connection Settings.................................................................................................................. 8

Serial Data Port Settings...................................................................................................................... 9

Connector Descriptions.................................................................................................... 10

Specifications ................................................................................................................... 12

RS-232 N LL Modem Wiring......................................................................................... 12

Network IP Address Configuration................................................................................. 13

Web Browsers and Proxy Servers.................................................................................... 13

Testing with a Telnet Connection.................................................................................... 14

SB72 User's Manual, 350030-006 Pa e 3

Overview

The SB72 comes prepro rammed and ready to run on your network. Before you can be in usin the device,

some basic confi uration is required to tell the SB72 what type of serial interface you want to use, the

network address you want the SB72 to respond to, the serial data baud rate, and the TCP/IP listenin port

number. There are three areas of confi uration: Hardware confi uration, Network confi uration, and

Operational confi uration.

Configuration

Hardware Configuration

Your specific confi uration will depend on whether you want to use RS-232, TTL, or RS-485. There are 2

serial ports (Ports) that can be confi ured by jumpers on the board and throu h the web interface. This

manual will refer to each serial port as Port 0 and Port 1. Once you have the hardware confi ured correctly,

you will select the correspondin software options usin the web interface to route serial data.

1. Connect to the desired serial interface: J6 for RS-232, or J2 for RS-485.

RS-232 Users: Connector J6 is wired to accept a standard PC type DTK 10-pin header to DB-9 cable,

which will result in a DB-9 pin-out of 2 = RX, 3 = TX, and 5 = GND. If connectin to a PC, make sure

to use a cross-wire cable or a null-modem adapter to swap RX and TX si nals.

SB72 User's Manual, 350030-006 Pa e 4

2. Confi ure the serial jumpers.

WARNING: Incorrect jumper settin s may result in dama e to driver components

Jumper RS-485

Port 0

Half Duplex

RS-485

Port 0

Full Duplex

RS-232

Port 1

RS-232

Port 0

TTL

Port 0

TTL

Port 1

JP1 CLOSE 2-3 CLOSE 1-2 X X OPEN X

JP2 CLOSED CLOSED X OPEN OPEN OPEN

JP3 X X CLOSED X OPEN X

JP4 OPEN OPEN or 2-3 RTS 2-3 CLOSE 1-2 OPEN X

JP5 OPEN OPEN or 2-3 CTS 2-3 CLOSE 1-2 OPEN X

Key: X = don’t care, Open = No connection, Closed = Jumper pins

Note for RS-232 Operation: The SB72 can run 2 channels without hardware handshakin . If RTS

and CTS are required, then only Port 1 can be used. RTS and CTS are available at TTL levels on

the J5 connector for both channels.

3. Connect the Ethernet port to your hub or computer

4. Provide re ulated 5V DC power to the board assembly. You can use the 5V power connector J8, or use

the power pins on J5.

5. Verify the power and Ethernet are confi ured correctly by makin sure the power led and link led are

on.

SB72 User's Manual, 350030-006 Pa e 5

Hardware Configuration Examples

RS-232

• Remove all jumpers

• Install Jumper JP3

• Optional: Install Jumpers JP4 and JP5 on pins 2-3 for RTS/CTS handshakin

RS-48

• Remove all jumpers

• Install Jumper JP2

• Install Jumper JP1 on pins 1-2 (full duplex) or 2-3 (half duplex)

SB72 User's Manual, 350030-006 Pa e 6

Network Configuration

The Hardware Confi uration steps above must be completed correctly before the software confi uration

can take place.

1. Download the IPSetup.exe utility from http://www.netburner.com/downloads/ipsetup.exe.

2. Run IPSetup.exe. You will see a dialo box like the one below:

3. Select the "Find" button and locate the SB72 in the list box. If your SB72 does not appear in the list

box, verify the power and link LED's are illuminated; if not, correct any cablin errors. Note that

IPSetup uses a UDP broadcast protocol similar to BOOTP and will not operate throu h a router.

4. If your network supports DHCP:

The assi ned IP address will appear in the "select a unit" window. Write down this address.

If your network does not support DHCP:

Confi ure the IP Address and Mask fields. If you need help selectin values, see the Selectin an IP

Address section of this manual. After you have entered the values, select the "Set" button to confi ure

the SB72 with the new parameters.

5. Verify the network connection is workin properly by executin the followin command from a

command prompt: "pin <ip address>".

SB72 User's Manual, 350030-006 Pa e 7

Operational Configuration

Once the network parameters have been confi ured you can use the web server interface to modify settin

of the SB72. To access the web pa e on the SB72, open a web browser and enter the numeric IP Address in

the address field.

Device Network Settings

SB72 Device Address Selects the IP address of the SB72 device. If DHCP is selected, the SB72 will

obtain IP address information automatically, includin the net mask, ateway,

and DNS server. If Static is selected, you need to supply the static IP address

in the edit box to the ri ht, as well as the other device network settin s

Device net mask When usin a static IP address, enter the net mask in this field

Device Gateway When usin a static IP address, enter the IP address of the Gateway in this

field

DNS Server When usin a static IP address, enter the IP address of the DNS Server in this

field

SB72 User's Manual, 350030-006 Pa e 8

Device Connection Settings

Server Listen Port: Select the checkbox and enter the listenin port number you want the TCP

serial server to listen on for incomin connections.

Client Activity Timeout

and Disconnect

If no activity is detected on a TCP/IP connection within this timeout period,

the TCP server will drop the connection.

Client Override Timeout If no activity is detected on a TCP/IP connection within this timeout period,

the TCP server will disconnect the current TCP/IP connection and allow the

new incomin connection request to connect.

Out oin Connections If this option is enabled, the SB72 will initiate a connection to an outside

destination when the selected conditions are met.

Options are:

• Don't Initiate Connections

• Connect on Power-up

• Connect when receivin serial data

If this option is enabled, you must enter values for the out oin destination

port number and destination address.

Out oin Port Number Destination port number

Out oin Address Either the name (e. . www.netburner.com) or numeric IP address (e. .

10.1.1.2) of the destination

Out oin Timeout Inactivity timeout for the out oin connection

SB72 User's Manual, 350030-006 Pa e 9

Serial Data Port Settings

Serial Data Port Selects the data port to be RS-232 or RS-485. Options are:

• Port 0 RS-232 or TTL

• Port 1 RS-232 or TTL

• Port 0 RS-485 Half Duplex

• Port 0 RS-485 Full Duplex

Data Baud Rate: Selects the baud rate of the serial data channel

Data Bits Select number of data bits

Data Parity Select none, odd or even parity

Data Stop Bits Select 1 or 2 stop bits

Flow Control Selects serial port flow control: none, Xon/Xoff, or RTS/CTS

SB72 User's Manual, 350030-006 Pa e 10

Connector Descriptions

J1 –Factory Test Connector, Dual Row 10-Pin Header

For factory use only.

J2 –RS-48 , Dual Row 10-Pin Header

The RS-485 interface support s 4-wire full duplex (FD), and 2-wire half duplex (HD). Note that jumpers

JP1 – JP5 must be confi ured correctly to FD or HD mode.

Pin Si nal Pin Si nal

1 FD RX- 2 GND

3 FD RX+ 4 GND

5 VCC 5V 6 GND

7 FD TX+ / HD + 8 GND

9 FD TX- / HD - 10 GND

J3 – Factory Test Connector, Dual Row 16-Pin Header

For factory use only.

J4 – SPI Interface Connector

Sin le row strai ht header

Pin Si nal

1 GND

2 DOUT

3 CLK

4 DIN

5 /SPI_CS3

J – Serial TTL Dual Row 10-Pin Header

This connector allows access to TTL level serial ports 0 and 1. Note that pin 9 is a VCC 5V input, which

allows for a sin le connector interface with TTL serial and power to the SB72.

Pin Si nal Pin Si nal

1 GND 2 CTS1

3 TX1 4 RX1

5 RTS1 6 RTS0

7 CTS0 8 TX0

9 VCC 5V 10 RX0

Inhaltsverzeichnis

Andere NetBurner Server Handbücher

NetBurner

NetBurner PK70EX-232 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung