NetComm NB1300 Technisches Handbuch

www.rsl.com.au PAGE 1 of 5

DSL Setup Document

How to install and set up your Netcomm NB-1300

INSTALL THE NB-1300 ......................................................................................................................................................................1

CONFIGURE THE COMPUTER...............................................................................................................................................................2

CONFIGURE THE ROUTER ...................................................................................................................................................................2

One-page setup .............................................................................................................................................................................3

Administration...............................................................................................................................................................................4

Status.............................................................................................................................................................................................4

Install the NB-1300

The NB1300 can connect either directly to a desktop computer or to a network via hub, switch or another router. All

connections are made to the computers using an ethernet or USB cable.

• Use straight-through cable for connecting to a normal port (MDI-X) on a hub or switch.

• Use crossover cable for connecting direct to a PC, server, or uplink port (MDI-II) on a hub or switch.

• Ensure the cable is not over 100 metres in length (or service degradation will result).

• If using the USB cable, additional installation is required; see below.

All connections to the Internet are made over ordinary phone cabling. Use the cabling supplied with the router or use

your own. The service will work over ordinary phone extension cords and other phone socket appliances (double

adaptors, etc); however, any noise over or damage to the appliances may result in problems accessing the Internet

service.

1. Plug the power cord into the router and then into a power point.

2. The RDY light will go red while internal checks are done; once complete, it will go off. If it does not, there may

be some problems.

3. The power LED should light up green and stay lit.

4. Plug the phone cord into the "ADSL" port on the router and then into the plug servicing the DSL-enabled line. If

you have multiple lines, ensure you have the correct line!

5. The ADSL Port LED should blink green until it negotiates an ADSL connection, after which it will stay steady.

6. USB connection:

a. Place the supplied CD-ROM in your computer.

b. Connect the supplied USB cable to the modem and to a USB port on your computer

c. Windows should detect the new hardware. When prompted to search for drivers select "Specify

location".

d. Browse to the driver letter of your CD-ROM drive and locate the "USB driver" folder.

e. Click "OK". The Wizard will locate the USB driver and prompt you to install it.

f. Once the driver is installed, it is configurable as a regular ethernet adaptor and will be set to

automatically accept an IP address from your modem.

7. Ethernet connection:

1300 764 764

5888

www.rsl.com.au PAGE 2 of 5

DSL Setup Document

3. The "Username and password" box will appear.

• Plug the appropriate ethernet cable into one of the ports on the back of the router and then into your

network device (network card on PC, hub, switch, router, etc).

8. The Link/Act LED should light up green and stay steady.

You are now physically connected. Next you need to configure a PC to access the router, after which you can

configure the router itself to access the Internet.

Configure the computer

Ensure that the computer is connected to the router, or connected to the network device (eg a hub) into which the

router is connected. Ensure the router is turned on. (see above).

Note: the following sets of configurations assume you will be using the router as the method for connecting to the

Internet, in routed mode. It is not for using the router in bridged mode.

1. Right-click on Network Neighborhood and select "Properties".

2. Select "TCP/IP". If it is not in the list it will need to be installed. This may require the Windows CD-ROM and

instructions are not provided here.

3. Select "Settings".

4. Put the following information in the appropriate tabs. If a tab isn't listed, it doesn't require changing.

• IP: Select "Obtain automatically".

• Gateway: router IP address (by default, 192.168.1.1)

• DNS: Select "Obtain automatically".

Configure the router

Default internal IP address: 192.168.1.1

Default username/password: admin/password

1. Open any web browser.

2. Type the internal IP address (eg 192.168.1.1) into the address section and press "enter".

4. Leave the username empty and type "admin" in the password.

5. Click "OK".

6. The web-based management system will open to the "OnePage setup screen". This is the first page that is

displayed when the web-based management system is opened and for ordinary Internet access, is the only

page required to be edited.

1300 764 764

5888

www.rsl.com.au PAGE 3 of 5

DSL Setup Document

One-page setup

7. Fill the fields as follows:

• LAN

o IP address: by default, 192.168.1.1 (the address of the modem)

o Subnet mask:255.255.255.0

• WAN

o Service name: you can leave blank or enter RSL COM.

o Username: enter the username assigned to you by RSL COM. This will be in the format

[email protected] and is not the same as your email address.

o Password: enter the password assigned to you by RSL COM.

o Disconnect timeout: leave blank

• WAN Type: select PPPoE LLC

• VC settings

o VPI: 8

o VCI: 35

o Static IP address: 0.0.0.0

o Subnet mask: 255.255.255.0

o Default gateway: 0.0.0.0

1300 764 764

5888

www.rsl.com.au PAGE 4 of 5

DSL Setup Document

• Bridge mode: disabled

Click "Apply". The router will save the settings and make a connection to RSL COM. You will now be able to use

any Internet software to browse the web, check your email, and so on.

Administration

Use these options if you wish to set up advanced network applications such as Port Address Translation, routing

options, change options such as the username, password or default IP address of the router, or view the current

network/connection status.

These applications all relate to how your network manages incoming and outgoing data, and do not relate to how

you connect to RSL COM. Note that changing some of these options may affect your ability to connect to RSL

COM, so only make changes if you are certain you require the modifications (eg for running servers, games,

controlling access to the Internet, and the like).

Use the manual that came with your modem to set these applications.

Status

Use these to display the status of the modem at any given time.

1300 764 764

5888

1300 764 764 PAGE 5 of 5www.rsl.com.au

DSL Setup Document

5888

Andere Handbücher für NB1300

Inhaltsverzeichnis

Andere NetComm Modem Handbücher

NetComm

NetComm NB5580W Bedienungsanleitung

NetComm

NetComm PlayStation 3 NB16WV-02 Bedienungsanleitung

NetComm

NetComm Webmaster CD1800 Bedienungsanleitung

NetComm

NetComm NF15ACV Bedienungsanleitung

NetComm

NetComm IG6000 Bedienungsanleitung

NetComm

NetComm NP7042 Bedienungsanleitung

NetComm

NetComm InModem 56 Bedienungsanleitung

NetComm

NetComm AM5698 Bedienungsanleitung

NetComm

NetComm AM5066 Bedienungsanleitung

NetComm

NetComm AM5065 Bedienungsanleitung

NetComm

NetComm Smart Modem SM5695 Bedienungsanleitung

NetComm

NetComm NB604N Technisches Datenblatt

NetComm

NetComm NB16WV-03 Bedienungsanleitung

NetComm

NetComm Vodafone MachineLink 3G Bedienungsanleitung

NetComm

NetComm NF18ACV Sicherheitsleitfaden

NetComm

NetComm Vodafone MachineLink 3G Bedienungsanleitung

NetComm

NetComm N3GS003 Bedienungsanleitung

NetComm

NetComm NB5PLUS4W Bedienungsanleitung

NetComm

NetComm NTC-3000 Series Bedienungsanleitung

NetComm

NetComm NTC-3000 Series Bedienungsanleitung

NetComm

NetComm NF18ACV Bedienungsanleitung

NetComm

NetComm BD3068 Bedienungsanleitung

NetComm

NetComm NF4V Bedienungsanleitung

NetComm

NetComm NB1300 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

EpiValley

EpiValley TATA indicom SXC-1080 Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung