NETGEAR PL1000 Bedienungsanleitung
Quick Start
Powerline 1000
Model PL1000
2
Package Contents
In some regions, a resource CD is included with your product.
3
Get Started
Powerline adapters give you an alternative way to extend your network
using your existing electrical wiring. Plug two or more Powerline adapters
into electrical outlets to create a wired network connection. You can add
up to eight Homeplug AV-certified and AV2-certified adapters to extend
your network. For a complete list of Homeplug AV-certified devices, visit
http://www.homeplug.org/certified_products.
4
Power LED
Factory Reset button
Ethernet port
Pick A Plug LED
Ethernet LED
Security button
Meet Your Adapter
Before you install your adapters, familiarize yourself with their LEDs,
buttons, and ports.
5
Power LED Solid green. The electrical power is on.
Solid amber. The adapter is in power saving mode.
Blinking green. The adapter is in the process of setting up
security.
O. The adapter is not receiving electrical power.
Ethernet LED Solid green. The Ethernet port is linked.
O. No Ethernet connection is detected.
Pick A Plug LED The Pick A Plug feature lets you pick the electrical outlet
with the strongest link performance, indicated by the color
displayed by the LED:
Red. Link rate < 50 Mbps (good).
Amber. Link rate > 50 and < 80 Mbps (better).
Green. Link rate > 80 Mbps (best).
O. The adapter did not find any other compatible Powerline
devices using the same encryption key.
Factory Reset
button
Press the Factory Reset button for one second, and then
release it to return the Powerline adapter to its factory
default settings.
Ethernet port Use an Ethernet cable to connect your wired devices,
including computers, WiFi routers, or game consoles, to your
Powerline network.
Security button Use the Security button to create a secure Powerline
network.
6
¾To install your adapters:
1. Plug in your new adapters.
2. Wait until the Pick A Plug LEDs are lit.
Congratulations. You installed your adapters and set up your network.
You can customize the network and security settings later.
7
Install Your Adapters
Do not plug your Powerline devices into extension cords, power strips, or surge
protectors.
Room 1 Room 2
8
Do More
Aer your Powerline network is installed and running, you can expand your
network, customize the network settings, and customize security.
Add Adapters
To add adapters before you configure the security feature, just plug them
in and connect the adapters to your equipment.
¾To add an adapter to a Powerline network with security
set:
1. Plug the adapter into a wall outlet where you want to add Internet
access.
2. If you used a private encryption key, press the Security button on
one of the adapters that is already a part of the network for two
seconds, and then press the Security button on the new adapter for
two seconds.
Both buttons must be pressed within two minutes.
Note: The Security button does not work in power saving mode.
Do not press the Security button on the Powerline adapter until
installation is complete and the adapters are communicating with each
other (indicated by the blinking Power LED). Pressing this button too
9
soon can temporarily disable Powerline communication. If this occurs, use
the Factory Reset button to return the Powerline adapter to its factory
default settings.
Customize Your Network Security
When you first set up your network, the setup uses a default encryption
key common to all Homeplug AV-certified adapters. You can change this.
¾To create a private secure network:
1. Wait until the Pick A Plug LEDs are lit.
2. Press the Security button for two seconds on one adapter, and then
press the Security button on one of the other adapters for two
seconds. Both buttons must be pressed within two minutes.
Note: The Security button does not work in power saving mode (see
Troubleshooting Tips on page 10).
Warning: Do not press the
Security
button on the Powerline adapter
until installation is complete and the adapters are communicating with
each other (indicated by the Power LED). Pressing this button too soon
can temporarily disable Powerline communication. If this occurs, use the
Factory Reset button to return the Powerline adapter to its factory
default settings.
If you add adapters later, use this procedure to add the new adapters to
your secure network.
10
Troubleshooting Tips
Power LED is o. Make sure that power is supplied to the electrical
outlet, and that the Powerline devices are not plugged
into an extension cord, power strip, or surge protector.
Power LED is amber. Power saving mode occurs when the Ethernet LED is
o. This can occur in the following circumstances:
• The Ethernet cable is unplugged.
• The device that is connected through the Ethernet
cable is turned o.
• The adapter is idle for 10 minutes.
It returns to normal mode within two seconds
aer the Ethernet link is established.
Pick A Plug LED is o. • If you already set network security, make sure
that all Powerline devices are using the same
encryption key; for information see the online user
manual.
• Press the Factory Reset button on each device
for one second to return the Powerline adapter to
its factory default settings.
Inhaltsverzeichnis
Andere NETGEAR Adapter Handbücher
NETGEAR
NETGEAR XAV2001 - Powerline AV Ethernet Adapter Bedienungsanleitung
NETGEAR
NETGEAR WNDA3200 Bedienungsanleitung
NETGEAR
NETGEAR WG111v3 - 54 Mbps Wireless USB 2.0 Adapter Bedienungsanleitung
NETGEAR
NETGEAR XAV5601 Bedienungsanleitung
NETGEAR
NETGEAR PTV1000 - Push2TV - TV Adapter Bedienungsanleitung
NETGEAR
NETGEAR XAV2602 Bedienungsanleitung
NETGEAR
NETGEAR XAV2501 - Powerline AV Ethernet Adapter Bedienungsanleitung
NETGEAR
NETGEAR XAVB1601 Bedienungsanleitung
NETGEAR
NETGEAR HDX101 - Powerline HD EN Adapter Bridge Bedienungsanleitung
NETGEAR
NETGEAR WNCE3001 Bedienungsanleitung
NETGEAR
NETGEAR EA101C Bedienungsanleitung
NETGEAR
NETGEAR Powerline 500 Bedienungsanleitung
NETGEAR
NETGEAR XET1001 - Powerline Network Adapter Bedienungsanleitung
NETGEAR
NETGEAR XAV5001 - Powerline AV 500 Adapter Bedienungsanleitung
NETGEAR
NETGEAR XAVB5501 Bedienungsanleitung
NETGEAR
NETGEAR TA612V Bedienungsanleitung
NETGEAR
NETGEAR WPN111 - RangeMax Wireless USB 2.0 Adapter Bedienungsanleitung
NETGEAR
NETGEAR WNDA3100v2 - RangeMax Dual Band Wireless-N USB 2.0... Bedienungsanleitung
NETGEAR
NETGEAR FA511 - 32-bit CardBus PC Card Mobile Bedienungsanleitung
NETGEAR
NETGEAR A7000 Bedienungsanleitung
