NETGEAR FSM7328S - ProSafe Switch Bedienungsanleitung

Andere Handbücher für FSM7328S - ProSafe Switch

7

Inhaltsverzeichnis

Andere NETGEAR Schalten Handbücher

NETGEAR

NETGEAR ProSafe GS504 Bedienungsanleitung

NETGEAR

NETGEAR GS908E Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE GS105PE Bedienungsanleitung

NETGEAR

NETGEAR GSM7312NA Bedienungsanleitung

NETGEAR

NETGEAR ProSafe GS108 Bedienungsanleitung

NETGEAR

NETGEAR FS509 Bedienungsanleitung

NETGEAR

NETGEAR GSM7224v2 - Layer 2 Managed Gigabit Switch Handbuch

NETGEAR

NETGEAR JFS516 Bedienungsanleitung

NETGEAR

NETGEAR ProSafe GSM5212P Bedienungsanleitung

NETGEAR

NETGEAR Signature GS908 Bedienungsanleitung

NETGEAR

NETGEAR GS810EMX Bedienungsanleitung

NETGEAR

NETGEAR GS208 Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE S3300 Handbuch

NETGEAR

NETGEAR JFS516v2 Bedienungsanleitung

NETGEAR

NETGEAR GSM4248PX Handbuch

NETGEAR

NETGEAR GS105NA Bedienungsanleitung

NETGEAR

NETGEAR GS308 Bedienungsanleitung

NETGEAR

NETGEAR GSM7312 - ProSafe Layer 3 Managed Gigabit... Bedienungsanleitung

NETGEAR

NETGEAR ProSafe GS700TP Bedienungsanleitung

NETGEAR

NETGEAR M4500 Series Handbuch

NETGEAR

NETGEAR M4300 Intelligent Edge Series Handbuch

NETGEAR

NETGEAR ProSafe GS108 Bedienungsanleitung

NETGEAR

NETGEAR Nighthawk GS808E Bedienungsanleitung

NETGEAR

NETGEAR EN516 - Hub - EN Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

7000 Series (Firmware 6.0.0.15)

Configuring VLANs and Routing

Scenario:

Creation of a 2 VLAN Routed network with access to the Internet via

an FVS Router/Firewall.

VLAN 3 being the Users PC domain

VLAN 2 being the Internet domain

Network Diagram:

Physical Setup:

1x FSM7328S Prosafe Layer 3 Managed switch - Firmware 6.0.0.15

4x Windows XP Computers (2x on each VLAN)

1 x FVS___ Prosafe Firewall Router

Logical Setup:

FVS___ : 192.10.10.1/24

VLAN 2 –192.10.10.0/24

VLAN 3 –172.10.11.0/24

VLAN2 IP address 192.10.10.254

VLAN3 IP address 192.10.11.254

WORKING INSTRUCTIONS

Set the Management IP address

1) Plugged the console cable to the Serial port of the switch and the serial port on the

PC

2) Open a new Hyper Terminal session (connecting via the COM port) –settings 9600,

8 , None , 1, None

3) Power Cycle the switch

4) Upon POST the User: prompt will appear

5) Username is admin , password “blank”

6) Type Enable to access the privileged mode (password “blank” )

7) Type network protocol none to reset the network settings

8) Type network parms <<Management IP>> <<Subnet Mask>> <<Default Gateway

IP>>. For example network parms 192.168.0.1 255.255.255.0 192.168.0.1

9) User copy system:running-config nvram:startup-config to save the configuration

10) Check with show network if the settings are correct

The switch should now be accessible patching a CAT5 Straight-through cable. The PC

NIC must be configured with an IP address within the same subnet used to configure the

management IP of the switch (Example: 192.168.0.2 255.255.255.0

Creating a Routing VLAN2 and Routing VLAN3 via the SmartWizard

1) Access the GUI

2) Browse to Smart Wizard –VLAN routing Wizard

3) Assign the VLAN ID

4) Select the port(s) members of the VLAN (Use CTRL to select multiple ports)

5) Assign the VLAN IP address and Subnet Mask

6) Click on Submit. The UNIT/SLOT/PORT entry will show the Virtual PORT created

and associated to the new VLAN.

7) Perform point 1-6 to create VLAN3 (with relevant IP address)

WEB GUI instructions

Creating a Routing VLAN2 and Routing VLAN3 via the SmartWizard

1) Access the GUI

2) Browse to Smart Wizard –VLAN routing Wizard

3) Assign the VLAN ID

4) Select the port(s) members of the VLAN (Use CTRL to select multiple ports)

5) Assign the VLAN IP address and Subnet Mask

6) Click on Submit. The following statement should be prompted.

7) Perform point 1-6 to create VLAN3 (with relevant IP address)

8) The following summary should be obtained:

Checking routing is in place on the switch

1) Browse to Routing –RIP –Interface Summary

2) The following situation should appear

NOTE: The RIP admin mode will show ENABLE only if at least one active device is

patched into a port in the relevant VLAN

NOTA BENE:

Router/Firewall:

If the firewall as in this case is patched into a port in a specific VLAN (VLAN2 here),

ensure its static routing table contains a route back to the VLAN IP address for each of

the other VLANS on the switch that require Internet access.

For example in this case the FVS Firewall must contain the following route:

192.10.11.0 (Subnet) 255.255.255.0 (Subnet Mask) 192.10.10.254 (Default Gateway).

On the other hand another option would be to run RIP on the Firewall.