NETGEAR ProSAFE FS726Tv2 Handbuch

350 East Plumeria Drive

San Jose, CA 95134

USA

September 2013

202-11325-01

ProSAFE 24-Port 10/100 Smart

Switch with 2 Gigabit Ports FS726Tv2

Hardware Installation Guide

ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and use it to register your product

at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support.

NETGEAR recommends registering your product through the NETGEAR website. For product updates and web

support, visit http://support.netgear.com.

Phone (US & Canada only): 1-888-NETGEAR.

Phone (Other Countries): Check the list of phone numbers at

http://support.netgear.com/general/contact/default.aspx.

Trademarks

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of

NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change

Revision History

Publication Part Number Publish Date Comments

202-11325-01 September 2013 First publication

Contents

Chapter 1 Introduction and Hardware Description

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

RJ-45 Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

SFP GBIC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Factory Defaults Button and Reset Button. . . . . . . . . . . . . . . . . . . . . . . . .11

Chapter 2 Installation

Step 1: Prepare the Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Step 2: Install the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Install the Switch on a Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Install the Switch in a Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Step 3: Check the Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Step 4: Connect Devices to the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Step 5: Install an SFP GBIC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Step 6: Apply AC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Step 7: Manage the Switch through a Web Browser or

through the Smart Control Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Chapter 3 Troubleshooting

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Troubleshooting Suggestions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Network Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Switch Integrity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Autonegotiation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Appendix A Physical and Technical Specifications

1. Introduction and Hardware

Description

The NETGEAR® ProSAFE® 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2 is a

state-of-the-art, high-performance, IEEE-compliant network solution for users who require the

flexibility of a small form-factor pluggable (SFP) GBIC slot. To simplify installation, the switch is

shipped ready for use out of the box.

The chapter covers the following topics:

•Overview

•Switch Features

•Package Contents

•Front Panel

•Back Panel

•LEDs

•Product Label

•RJ-45 Ports

•SFP GBIC Module

•Factory Defaults Button and Reset Button

Note: For more information about the topics covered in this manual, visit

the support website at support.netgear.com.

Note: Firmware updates with new features and bug fixes are made

available from time to time on downloadcenter.netgear.com. Some

products can regularly check the site and download new firmware,

or you can check for and download new firmware manually. If the

features or behavior of your product do not match what is described

in this guide, you might need to update your firmware.

Introduction and Hardware Description

ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

Overview

This hardware installation guide is for the NETGEAR ProSAFE 24-Port 10/100 Smart Switch

with 2 Gigabit Ports FS726Tv2. The switch provides twenty-four 10/100BASE-T ports, two

10/100/1000BASE-T ports, one of which functions as a combo port, and one small

form-factor pluggable (SFP) GBIC slot that functions as a combo port.

You can make high-speed connections using the Gigabit Ethernet ports. For example:

•Connecting switches to each other with high-speed links

•Connecting to a network backbone

•Linking to high-speed servers

•Providing 10/100/1000 Mbps copper and 100/1000 Mbps fiber connectivity

Note: In this guide, the NETGEAR ProSAFE 24-Port 10/100 Smart Switch

with 2 Gigabit Ports FS726Tv2 is referred as the switch.

The switch also provides the benefit of administrative management with a complete package

of features to monitor, configure, and control the network. With the web management

interface, you can view the switch’s many features and use them in a simple and intuitive

manner. The switch’s management features include configuration for port and switch

information, VLAN for traffic control, port trunking for increased bandwidth, and Class of

Service (CoS) for traffic prioritization. Initial discovery of the switch on the network requires

the Smart Control Center, a utility that runs on a computer.

You can use the switch freestanding or rack-mounted in a wiring closet or equipment room.

The switch is IEEE-compliant and provides low latency for high-speed networking. All ports

can automatically negotiate to the highest speed. This capability makes the switch well suited

for environments that have a mix of Ethernet, Fast Ethernet, and Gigabit Ethernet devices. In

addition, all RJ-45 ports operate in half- or full-duplex mode. The maximum segment length is

328 feet (100 meters) over a Category 5 twisted-pair cable.

You can use the switch as a desktop to build a small network that enables you to have

1000 Mbps access to a file server. With full duplex enabled, the switch port connected to the

server or computer can provide 2000 Mbps throughput.

Introduction and Hardware Description

ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

Figure 1. Example of a network configuration

Switch Features

The following list identifies the key features of the switch:

•Twenty-four RJ-45 10/100 Fast Ethernet switching ports.

•Two RJ-45 10/100/1000 Gigabit Ethernet switch ports, one of which (26T) functions as a

combo port.

•One small form-factor pluggable (SFP) GBIC slot (26F) that functions as a combo port.

A combo port is a single port with two physical connections, SFP fiber and RJ-45 copper.

The RJ-45 copper port corresponding to the combo port is the 10/100/1000 autosensing

Gigabit Ethernet switch combo port. The SFP fiber port corresponding to the combo port

is the SFP GBIC slot. If both the RJ-45 copper combo port and the SFP fiber combo port

have devices connected, the device that was connected first takes precedence. In other

words, the combo port functions on a first-come, first-served basis.

The following SFP GBICs are supported:

-1000BASE-SX (NETGEAR AGM731F)

-1000BASE-LX (NETGEAR AGM732F)

•The switch provides full compatibility with IEEE standards:

-IEEE 802.3i (10BASE-T)

-IEEE 802.3u (100BASE-TX, 100BASE-FX)

Introduction and Hardware Description

ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

-IEEE 802.3x (full-duplex flow control)

-IEEE 802.3z (1000BASE-X)

-IEEE 802.3ab (1000BASE-T)

-IEEE 802.3az (EEE)

•Autosensing and autonegotiating capabilities for all ports.

•Auto MDI/MIDX technology is supported on all ports.

•Automatic address-learning function to build the packet-forwarding information table. The

table contains up to 8 K Media Access Control (MAC) addresses.

•Full- and half-duplex functions for all 10/100/1000 Mbps ports.

•Store-and-forward transmission to remove corrupt packets from the network.

•Full-duplex IEEE 802.3x pause frame flow control.

•Active flow control to minimize packet loss and frame drops.

•Half-duplex back-pressure control.

•Per-port LEDs and system Power LED.

•Internal power supply.

•Standard 1U high, rack-mountable 19-inch chassis.

Package Contents

The following figure shows the package contents of the switch.

350 East Plumeria Drive

San Jose, CA 95134

USA

Sept 2013

202-11251-01

350 East Plumeria Drive

San Jose, CA 95134

USA

Sept 2013

202-

1251-01

ProSAFE Fast Ethernet PoE Smart

Switch FS726Tv2

Hardware Installation Guide

Figure 2. Package contents

Introduction and Hardware Description

ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

Verify that the package contains the following:

•NETGEAR ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

•Rubber footpads for tabletop installation

•Power cord

•Rack-mount kit for installing the switch in a 19-inch rack

•Smart Switch resource CD with the Smart Control Center utility and a link to the online

Software Administration Manual.

•Installation guide

•Warranty support information card

If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep

the carton, including the original packing materials, in case you need to return the product for

repair.

Front Panel

The switch provides twenty-four 10/100BASE-T ports, two 10/100/1000BASE-T copper ports,

one of which (26T) is a combo port, and one small form-factor pluggable (SFP) GBIC slot

(26F), which functions as a combo port.

1 through 4,

see Figure 4

567

Combo port

[26T and 26F]

Figure 3. Front panel

Figure 4. Close up left side of the front panel

Introduction and Hardware Description

ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

The front panel contains the following components:

1. Power LED

2. Recessed Defaults button to restore the switch to the factory defaults

3. Recessed Reset button to reboot the switch

4. Twenty-four Link/ACT port LEDs

5. Twenty-four RJ-45 10/100BASE-T ports

6. Two RJ-45 Gigabit Ethernet ports with corresponding Link/ACT LEDs

7. One small form-factor pluggable (SFP) GBIC slot with a corresponding Link/ACT LED

Back Panel

The back panel provides a 100–240 VAC/50–60 Hz universal power inlet, which is a standard

AC power receptacle that accommodates the supplied power cord.

Figure 5. Back panel

LEDs

The following table describes the LEDs.

Table 1. LED descriptions

Port LED Designation

(Not applicable, system LED) Power • Off. Power is disconnected.

•Solid green. Power is supplied to the switch and the

switch is operating normally.

Twenty-four 10/100BASE-T

ports (one LED for each port) Link/ACT • Off. No link is established on the port.

•Solid green.A valid link of any speed is established on the

port.

•Blinking green. Packet transmission or reception occurs

at any speed on the port.

Two Gigabit Ethernet ports

(one LED for each port: 25

and 26T)

Link/ACT • Off. No link is established on the port, or the

•Solid green. A valid 1000 Mbps link is established on the

port.

•Blinking green. Packet transmission or reception occurs

at 1000 Mbps on the port.

•Solid yellow. A valid 10 or 100 Mbps link is established on

the port.

•Blinking yellow. Packet transmission or reception occurs

at 10 or 100 Mbps on the port.

Introduction and Hardware Description

ProSAFE 24-Port 10/100 Smart Switch with 2 Gigabit Ports FS726Tv2

Product Label

The product label on the back panel of the switch shows the hardware model number and

version, the software version, the unique MAC address, and the unique serial number. The

following figure shows a generic product label.

Figure 6. Generic product label

RJ-45 Ports

RJ-45 ports are autosensing ports. When you insert a cable into an RJ-45 port, the switch

automatically ascertains the maximum speed (10, 100, or 1000 Mbps) and duplex mode

(half- or full-duplex) of the attached device. All ports support a twisted-pair cable that is

terminated with an 8-pin RJ-45 plug.

To simplify the procedure for attaching devices, all RJ-45 ports support Auto MDI/MIDX. This

technology enables you to attach devices to the RJ-45 ports with either straight-through or

crossover cables. When you insert a cable into the switch’s RJ-45 port, the switch

automatically configures the RJ-45 port to enable communications with the attached device.

With Auto MDI/MIDX technology, you do not need to configure uplink connections, and you

do not need to think about whether to use crossover or straight-through cables when you

attach a device.

One SFP GBIC slot (one LED

for slot 26F) Link/ACT • Off. No link is established on the GBIC in the slot.

•Solid green. A valid 1000 Mbps link is established on the

GBIC in the slot.

•Blinking green. Packet transmission or reception occurs

at 1000 Mbps on the GBIC in the slot.

•Solid yellow. A valid 100 Mbps link is established on the

GBIC in the slot.

•Blinking yellow. Packet transmission or reception occurs

at 100 Mbps on the GBIC in the slot.

Table 1. LED descriptions (continued)

Port LED Designation

Andere Handbücher für ProSAFE FS726Tv2

Inhaltsverzeichnis

Andere NETGEAR Schalten Handbücher

NETGEAR

NETGEAR EN516 - Hub - EN Bedienungsanleitung

NETGEAR

NETGEAR GS108Tv3 Bedienungsanleitung

NETGEAR

NETGEAR MS108UP Bedienungsanleitung

NETGEAR

NETGEAR EN308TC - 8 Port 10 Base-T Hub Bedienungsanleitung

NETGEAR

NETGEAR GS750E Handbuch

NETGEAR

NETGEAR GS724AT - ProSafe Gigabit Smart Switch Bedienungsanleitung

NETGEAR

NETGEAR ProSafe XS712T Bedienungsanleitung

NETGEAR

NETGEAR GS700TR Series Handbuch

NETGEAR

NETGEAR GS116v2 Bedienungsanleitung

NETGEAR

NETGEAR M4350 Series Bedienungsanleitung

NETGEAR

NETGEAR M4250 Series Bedienungsanleitung

NETGEAR

NETGEAR ProSAFE JGS516PE Bedienungsanleitung

NETGEAR

NETGEAR EN104TP EN104TP EN104TP Bedienungsanleitung

NETGEAR

NETGEAR GSM7248 - ProSafe Switch Bedienungsanleitung

NETGEAR

NETGEAR GS105v5 Bedienungsanleitung

NETGEAR

NETGEAR FSM7328S - ProSafe Switch Bedienungsanleitung

NETGEAR

NETGEAR GC110 Bedienungsanleitung

NETGEAR

NETGEAR FS108P - ProSafe Switch Bedienungsanleitung

NETGEAR

NETGEAR ProSafe GSM5212P Bedienungsanleitung

NETGEAR

NETGEAR ProSafe GSM7228PS Bedienungsanleitung

NETGEAR

NETGEAR EN104 - Hub - EN Bedienungsanleitung

NETGEAR

NETGEAR GSM712 Bedienungsanleitung

NETGEAR

NETGEAR FS 524S Bedienungsanleitung

NETGEAR

NETGEAR XS728T ProSAFE Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung