NETGEAR ProSAFE FS726Tv2 Bedienungsanleitung
Installation Guide
NETGEAR ProSAFE Smart Switch™ FS726T v2
Package Contents
•NETGEAR ProSAFE Smart Switch™ FS726T v2
•Rubber footpads for tabletop installation
•AC power cord
•Rack-mount kit for rack installation
•Installation guide
•Smart Switch resource CD that includes the Smart Control Center Utility
and FS726Tv2 Hardware Installation Guide. (A link to the online FS726Tv2
Software Administration Manual is on the resource CD.)
Configure the Switch
Install the Smart Control Center Utility and use it to configure the switch.
Install the Smart Control Center Utility on a Computer
1. Insert the resource CD into your CD drive.
2. Run the Setup program to install the Smart Control Center Utility.
The Installation Wizard guides you through the installation.
Connect Your Smart Switch
If you have a DHCP server in you network, see Connect the Switch to Your
Network.
If you are using static IP addresses in you network, first see Configure the
Switch with a Static IP Address, and then see Connect the Switch to Your
Network.
Configure the Switch with a Static IP Address
If you are using a static IP address in you network, configure the switch IP
address before connecting the switch to your network. The default IP address of
the switch is 192.168.0.239.
Note: If you are using a DHCP server in your network, this procedure does not
apply to you; instead, go directly to Connect the Switch to Your Network.
1. Set up the computer with a static IP address in the 192.168.0.x subnet.
2. Connect the computer to the switch.
Connect the Switch to Your Network
1. Connect each computer to an RJ-45 network port on the switch front
panel.
Use Category 5 (Cat 5) or better Ethernet cable terminated with an RJ-45
connector to make these connections.
2. Connect the switch to your network.
3. Power on the switch.
4. Verify that the computer with the Smart Control Center Utility is on the
same subnet as the switch.
Internet
Configure the Switch with the Smart Control Center
Utility
1. Double-click the Smart Control Center Utility icon on your desktop or
click the icon in the Windows Start menu to run the utility and view this
screen.
2. Click the Discover button.
The Smart Control Center Utility finds the switch and displays its MAC
address, IP address, and model number.
If the utility does not discover your switch, verify that the cable connections
are secure and that the IP address configuration of the computer is in the
same subnet as the switch, and click the Discover button.
August 2013
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks
of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject
to change without notice. © NETGEAR, Inc. All rights reserved.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134 USA
3. Click the row for the switch that you want to configure.
4. Click the Web Browser Access button to view the switch Login screen.
5. Enter the default password of password in lower-case letters and click the
Login button.
The System Information screen displays.
6. Configure the switch for your network.
For more information, see the FS726Tv2 Software Administration Manual.
Troubleshooting Tips
Here are some tips for correcting simple problems you might have.
•Be sure to power on your computer and switch in the following sequence:
1. Turn on the switch and wait about two minutes.
2. Turn on the computer and connect to the switch.
•Make sure the Ethernet cables are plugged in.
For each powered-on computer connected to the switch, the corresponding
switch LAN port status LED is lit.
•Make sure the network settings of the computer are correct.
In most cases, computers should be configured to obtain an IP address
through DHCP. If your network uses static IP addresses, be sure that the
switch and computer are configured with valid IP addresses. For more
information, see the software administration manual.
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product
and use it to register your product at https://my.netgear.com.
You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website.
For product updates and web support, visit http://support.netgear.com.
NETGEAR recommends that you use only the official NETGEAR support
resources.
For additional information about setting up, configuring, and using your smart
switch, see the software administration manual.You can get the manual online at
http://downloadcenter.netgear.com.
Andere Handbücher für ProSAFE FS726Tv2
1
Andere NETGEAR Schalten Handbücher
NETGEAR
NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart... Handbuch
NETGEAR
NETGEAR FS508 - Switch Bedienungsanleitung
NETGEAR
NETGEAR GS108Tv2 - ProSafe Gigabit Smart Switch Coming... Bedienungsanleitung
NETGEAR
NETGEAR GSM7224v2 - Layer 2 Managed Gigabit Switch Handbuch
NETGEAR
NETGEAR FS108 - ProSafe 10/100 Desktop Switch Bedienungsanleitung
NETGEAR
NETGEAR FS108P - ProSafe Switch Bedienungsanleitung
NETGEAR
NETGEAR GS748T - ProSafe Smart Switch Bedienungsanleitung
NETGEAR
NETGEAR M7100 Series Bedienungsanleitung
NETGEAR
NETGEAR GS700TR Series Handbuch
NETGEAR
NETGEAR GSS108E Handbuch
NETGEAR
NETGEAR ProSafe GS108v3 Bedienungsanleitung
NETGEAR
NETGEAR ProSafe GS108 Bedienungsanleitung
NETGEAR
NETGEAR GS728TPv2 Bedienungsanleitung
NETGEAR
NETGEAR ProSafe GSM7324 Bedienungsanleitung
NETGEAR
NETGEAR ProSAFE JGS516PE Bedienungsanleitung
NETGEAR
NETGEAR FSM726S Bedienungsanleitung
NETGEAR
NETGEAR ProSAFE GS108PEv3 Bedienungsanleitung
NETGEAR
NETGEAR GSM7212 - ProSafe Switch Bedienungsanleitung
NETGEAR
NETGEAR MS510TX Handbuch
NETGEAR
NETGEAR GS108LP Installationsanleitung
