New Buck Corporation 329 Bedienungsanleitung

MODEL 329

MAY BE INSTALLED IN A SOLID FUEL BURNING FIREPLACE, AS A

FREESTANDING FIREPLACE OR WITH AN OPTIONAL WOODEN SURROUND.

WARNING: If the information in this manual is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

− Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s in-

structions.

• If you cannot reach your gas supplier, call the fire department.

− Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed.

Provisions for adequate combustion and ventilation air must be provided. Refer to section “

Producing Adequate Ventilation” page 32.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance

Manufacturer: NEW BUCK CORPORATION

P.O. Box 69

8000 Highway 226 South

Spruce Pine, NC 28777

This appliance is intended for supplemental

heating.

Revised December 2006

VENT-FREE

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

TABLE OF CONTENTS 329

SECTION I: Safety Information........................................................................................ 1

SECTION II: Fireplace Preparation................................................................................... 4

Fireplace Clearances ........................................................................................................... 5

Gas Connection................................................................................................................... 5

Placement of Logs………………………………………………………………………6-7

Gas Pressure Check............................................................................................................. 8

Lighting Instructions - ITT Millivolt Valve....................................................................... 9

Lighting Instructions - SIT Modulating Valve or -SIT Manual……………..…………...13

Lighting Instructions - SIT Millivolt Valve...................................................................... 17

Flame Check ..................................................................................................................... 21

Heat Output....................................................................................................................... 21

Wiring Diagram ................................................................................................................ 22

SECTION III: Solid Fuel Burning Fireplace Installation (FP)........................................ 24

SECTION IV: Freestanding Installation (FS).................................................................. 26

SECTION V: Alcove Installation ................................................................................... 28

SECTION VI: Wooden Surround Installation (WS) ........................................................ 29

SECTION VII: Installation-After Market Mobile Home ................................................ 31

SECTION VIII: Producing Adequate Air........................................................................ 32

Ventilation Air From Inside.............................................................................................. 34

Ventilation Air Outdoors .................................................................................................. 35

Important Safeguards ........................................................................................................ 36

Cleaning ............................................................................................................................ 36

Trouble Shooting .............................................................................................................. 37

Service and Repair Parts ................................................................................................... 41

Replacement Parts............................................................................................................. 42

Warranty ........................................................................................................................... 50

SECTION I

SAFETY INFORMATION WARNINGS

IMPORTANT: READ THIS OWNER’S MANUAL CAREFULLY AND COMPLETELY

BEFORE TRYING TO ASSEMBLE, OPERATE, OR SERVICE THE APPLIANCE.

IMPROPER USE OF THESE LOGS CAN CAUSE SERIOUS INJURY OR DEATH FROM

BURNS, FIRE, EXPLOSION, AND CARBON MONOXIDE POISONING.

Early signs of carbon monoxide poisoning resemble the flu, with headaches, dizziness, and/or

nausea. If you have these signs, the heater may not be working properly. Get fresh air at once!

Have heater serviced.

Some people-pregnant women, persons with heart or lung disease, anemia, those under the

influence of alcohol, and those at high altitudes-are more affected by carbon monoxide than

others.

CAUTION: Strong drafts, such as a ceiling fan placed directly in front of the heater

(pulling from either direction) may create sooting. Sooting will discolor

walls.

1. The installation must conform with local codes ,or in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1/NFPA54.

2. This appliance may be installed in an After-Market* Manufactured (Mobile) Home,

where not prohibited by state or local codes.

* (After-Market: Completion of sale, not for purpose of resale from the manufacturer.)

This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases.

NOTE: See Section VII, “Producing Adequate Ventilation” page 32.

IMPORTANT: VENT-FREE HEATERS ADD MOISTURE TO THE AIR. ALTHOUGH THIS

IS BENEFICIAL, INSTALLING HEATER IN ROOMS WITHOUT ADEQUATE

VENTILATION MAY CAUSE MILDEW TO FORM FROM TOO MUCH MOISTURE.

3. Never install this heater:

♦ in a recreational vehicle, bathroom, bedroom, or any other sleeping quarters

♦ where curtains, furniture, clothing, or other flammable objects are less than 42" from the

front of the heater

♦ in high traffic areas or in windy areas

4. Two models are available. One specific model for propane (LP), and one for natural gas.

Use the correct type gas for your home. Do not convert from one gas type to another.

“WARNING: ANY CHANGE TO THIS HEATER OR ITS CONTROLS CAN BE

DANGEROUS.”

Page 1

5. If this heater is used with propane gas, do not place propane supply tank (s) inside any structure.

6. What To Do IF You Smell Gas:

Shut off gas supply.

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the fire department.

7. When operated for the first time, the logs may emit a “paper burning” smell. This smell will

gradually diminish and will be totally eliminated after the first few hours of operation. Run the gas

logs with the flue damper open during this time. Do not use blower at this time.

8. “This heater shall not be installed in a confined space or unusually tight construction unless

provisions are provided for adequate combustion and ventilation air.” See “Producing

Adequate Ventilation”, page 32.

9. Surface of gas logs becomes very hot when operating. Keep children and adults away from hot

surface. Gas logs will remain hot for sometime after shutdown. Allow surface to cool before

touching.

10. Do not place clothing or other flammable material on or near the appliance.

11. If equipped, fresh air damper must be closed.

12. Keep appliance area clean and free from combustible materials, gasoline, and other flammable

flammable vapors and liquids. .

13. If burner shuts off, do not relight until you provide fresh outside air. If burner continues to shut off,

have unit serviced.

14. Do not use this heater if any part has been under water. Immediately call qualified service

technician to inspect the room heater and to replace any part of the control system and any

gas control which has been under water.

15. Turn off the heater and let cool before servicing.

16. These logs are made of bonded fiber. When removing logs and base, do not damage the bonded

material. If the material is damaged extensively, loose fiber dust could be emitted into the air.

17. Any safety screen or guard removed for servicing an appliance must be replaced prior to

operating the heater.

18. This appliance is intended for supplemental heating.

19. “WARNING: Any change to this heater or its controls can be dangerous.”

20. Installation and repairs should be performed by a qualified service person. The appliance

should be inspected before use and at least annually by a professional service person. More

frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.

It is imperative that control compartments, burners and circulating air passageways of the

appliance be kept clean.

Page 2

21. All heater screens must be kept closed when operating the gas logs.

22. . ”WARNING: Failure to keep the primary air opening (s) of the burner (s) clean may result

in sooting and property damage.”

23. Do not use this heater for burning trash or cooking. Never place matches, paper, garbage, or any

other material on top of logs or into the flames.

24. Do not install or operate this heater in areas where impurities in the air exist (such as tobacco

smoke or heavy cooking grease). Particles from impurities may discolor walls.

25. Due to high temperatures, the appliance should be located out of traffic and away from

furniture and draperies.

26. Children and adults should be alerted to the hazards of high surface temperature and should

stay away to avoid burns or clothing ignition.

27. Young children should be carefully supervised when they are in the same room with the

appliance.

28. An unvented room heater having an input rating of more than 10,000 Btu per hour shall not

be installed in a bedroom or bathroom.

29. The appliance and its appliance main gas valve must be disconnected from the gas supply

piping system during any pressure testing of that system at test pressure in excess of 1/2 psi

(3.5 kPa).

30. The appliance must be isolated from the gas supply piping system by closing its equipment

shut-off valve during any pressure testing of the gas supply piping system at test pressures

equal to or less than 1/2 psi (3.5 kPa).

31. “WARNING: Do not allow fans to blow directly into fireplace. Avoid any drafts that alter

burner flame patterns.”

32. “WARNING: Do not use a blower insert, heat exchanger insert or other accessory not

approved for use with this heater.”

33. Adequate clearances around air openings. Nothing may be placed over any of the air openings

on this appliance, or can any of the air openings be modified in anyway.

34. A fireplace screen must be in place when the appliance is operating and, unless other

provisions for combustion air are provided, the screen shall have an opening (s) for introduction

of combustion air.

35. WARNING: Any glass doors shall be fully opened when the appliance is in operation.

Page 3

SECTION II

FIREPLACE PREPARATION

The fireplace needs to be prepared before installing the heater.

A. Turn off the gas supply to the fireplace.

WARNING: BEFORE INSTALLING IN A SOLID-FUEL BURNING

FIREPLACE, THE CHIMNEY FLUE AND FIREBOX MUST BE

CLEANED OF SOOT, CREOSOTE, ASHES, AND LOOSE PAINT BY A

QUALIFIED CHIMNEY CLEANER.

“WARNING: DO NOT ALLOW FANS TO BLOW DIRECTLY

INTO THE FIREPLACE. AVOID DRAFTS THAT ALTER BURNER

FLAME PATTERNS.”

“WARNING: DO NOT USE A BLOWER INSERT, HEAT

EXCHANGER INSERT OR OTHER ACCESSORIES NOT APPROVED

FOR USE WITH THIS HEATER.”

WARNING: ANY OUTSIDE AIR DUCTS AND/OR ASH DUMPS IN

THE FIREPLACE SHALL BE PERMANENTLY CLOSED AT TIME OF

APPLIANCE INSTALLATION.

B. Read the following sections before installing your unit; Section III, page 24

Installation In A Solid-Fuel Burning Fireplace and Section VIII, page 32

Producing Adequate Ventilation.

WARNING: CUTTING ANY SHEET-METAL PARTS OF THE

SOLID –FUEL BURNING FIREPLACE OR LISTED VENTLESS

FIREBOX ENCLOSURE IN WHICH THE UNVENTED FIREPLACE

INSERT IS TO BE INSTALLED IS PROHIBITED.

NOTE: ”IF THE FACTORY BUILT FIREPLACE HAS NO GAS

ACCESS HOLE(S) PROVIDED, AN ACCESS HOLE OF 1.5 inch

(37.5mm) DIAMETER OR LESS MAY BE DRILLED THROUGH THE

LOWER SIDES OR BOTTOM OF THE FIREBOX IN A PROPER

WORKMANLIKE MANNER. THIS ACCESS HOLE MUST BE

PLUGGED WITH NON-COMBUSTIBLE INSULATION AFTER THE

GAS SUPPLY LINE HAS BEEN INSTALLED.”

REFRACTORY, GLASS DOORS , SCREEN RAILS, SCREEN MESH

AND SOLID-FUEL LOG GRATES (IF APPLICABLE) CAN BE

REMOVED FROM THE FIREPLACE BEFORE INSTALLING THE

UNVENTED FIREPLACE INSERT.

Page 4

INSTALLATION AND CLEARANCES

To ensure a safe installation into a masonry or factory built fireplace, the following instructions must be

carefully followed:

(1) Sidewall Clearances:

Clearance from the side of the fireplace opening to any adjacent combustible wall

should not be less than: right side 7", left side 7".

(2) Ceiling Clearances:

The ceiling height should not be less than 24" from the top of the fireplace opening.

(3) Mantel Clearances:

Clearances from top of heater to mantel or mantel supports should not be less than 20".

NOTE: See the following sections for installation options: Section III, page 24, Installation In A Solid-

Fuel Burning Fireplace, and Section IV, page 26 Freestanding Installation, and Section V, page 28

Alcove Installation, and Section VI, page 29 Optional Wooden Mantel Installation

WA R N I N G : ANY CHANGE TO THIS HEATER OR ITS CONTROLS CAN BE

DANGEROUS.

GAS CONNECTION

Check gas type. Use only the type of gas indicated on the valve rating plate. If the

type of gas listed on the plate is not your type of gas supply, DO NOT INSTALL. Contact your dealer

for proper model.

Always use an external regulator for all LP heaters to reduce the supply tank pressure to a maximum of

13" W.C. This is in addition to the regulator furnished with the heater.

WA R N I N G : CONNECTION DIRECTLY TO AN UNREGULATED LP TANK CAN CAUSE

AN EXPLOSION.

The normal gas connection is 3/8” N.P.T. made at the left side (facing the front of the appliance) of the

appliance. If a right side connection is desired, the connecting pipe may be led under the rear of the

burner base to terminate at the right side for connection to the inlet of the valve.

NOTE: The connecting pipe must be internally tinned copper tubing for use with natural gas. Test for

leaks using a solution of soap and water after completing the connection. DO NOT USE OPEN

FLAME.

NOTE: “If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1.5 inch

(37.5mm) diameter or less may be drilled through the lower sides or bottom of the fire box in a proper

workmanlike manner. This access hole must be plugged with non-combustible insulation after the gas

supply line has been installed.”

WARNING: Installation and repairs should be performed by a qualified service person. The

appliance should be inspected before use and at least annually by a professional service person.

More frequent cleaning may be required due to excessive lint from carpeting, bedding material,

etc. It is imperative that control compartments, burners and circulating air passageways of the

appliance be kept clean.

Page 5

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only

parts specifically approved with this heater may result in property damage or personal injury.

(1) Front Log #1 (Slim Log wrapped in cardboard box) . Place the log between front portion of

burner and log grates.

(2) Middle Glow Log #2 . Place rear of log on top of middle log supports located in open center por-

tion of burner base. Front of log should rest slightly behind the rear line of burner holes on the

front portion of the burner. Align the Notch on the left front bottom side of the log over the exist-

ing hold down nut of the burner. This should align the log at the right position from left or right

on the burner.

(3) Rear Log #3. Place log in rear log supports center from left to right.

(4) Left Top Log #4. Log has two (2) holes in the bottom front side. Align the holes with the two (2)

pins located on the left top of log #2. Rear of log #4 should rest on the left top end of the rear log

#3.

WARNING: POSITIONING OF LOGS IS VERY CRITICAL (SEE DIAGRAM ABOVE).

CR3329 CERAMIC LOG SET PLACEMENT FOR MODEL 329

(1-L)

(2)

(4)

(3)

(1-R)

Page 6

Inhaltsverzeichnis

Andere New Buck Corporation Gasheizung Handbücher

New Buck Corporation

New Buck Corporation 61TV Bedienungsanleitung

New Buck Corporation

New Buck Corporation 32 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 60 Bedienungsanleitung

New Buck Corporation

New Buck Corporation CR8T Bedienungsanleitung

New Buck Corporation

New Buck Corporation 1110 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 1127B Bedienungsanleitung

New Buck Corporation

New Buck Corporation 34 Bedienungsanleitung

New Buck Corporation

New Buck Corporation 384 Bedienungsanleitung

Beliebte Gasheizung Handbücher anderer Marken

Superior

Superior BGE18NV Bedienungsanleitung

Dru

Dru Room-sealed atmospheric gas-fired heating... Bedienungsanleitung

klover

klover TKR 35 Bedienungsanleitung

Rothenberger Industrial

Rothenberger Industrial 035984 Bedienungsanleitung

Hargrove

Hargrove Timberland Glow Kurzanleitung

Kinder

Kinder Cameo BF Bedienungsanleitung

Qlima

Qlima GH 438 B-2 Handbuch

Desa

Desa 125-R Bedienungsanleitung

Gasmate

Gasmate AH100 Series Bedienungsanleitung

Medallion

Medallion MBP20TLB Kurzanleitung

Clarke

Clarke DEVIL 910SS Bedienungsanleitung

Brant Radiant Heaters

Brant Radiant Heaters QTD Series Montageanleitung

L.B. White

L.B. White Therma Grow HW220 Handbuch

Sealey

Sealey LP35.V5 Bedienungsanleitung

Italkero

Italkero Falo Evo Bedienungsanleitung

Desa

Desa 30LP Bedienungsanleitung

Williams

Williams 2509822A Bedienungsanleitung

Romotop

Romotop Heckla 1301 Technische Daten