Nexa KD-134A/10Y Bedienungsanleitung

The instruction of smoke alarm devices

KD-134A/10Y with Lithium battery

1134

Nexa Trading AB, Box 12200

402 42 Göteborg

13807/KD-134A/10Y

NEXA13807-CPR-001

EN14604:2005/AC:2008

Fire Safety and installed in buildings

The Instruction of Smoke Detector KD-134A/10Y with Lithium battery

Your wise choice of using smoke detector KD-134A/10Y is greatly appreciated. Please read the operation instruction before using

it and keep the instruction well after reading.

1. Summary:

The smoke detector works on the principle that infrared scatters in the smoke to probe the smoke which is generated by the

incomplete combustion at the initial stage of the fire. It consists of photoelectric system, signal processing identification circuit and

alarm circuit. The infrared scatters on the surface of the smoke when the smoke enters the darkroom of the detector, then the

photoelectric diode receives the scattered light and generates the photoelectric signal current. The photoelectric signal generates

the alarm signal after being processed by the identification circuit, accordingly the purpose of alarming is achieved. The product

KD-134A/10Y has a special design, modern and fashion, small and artistic, and is of convenience to use.

2. Tec hnic al P aram eter :

This smoke detector contains a 10-year lithium battery

Power Source: 9V battery Lithium, Long life. Recommended :ULTRALIFE U9VL-J, GOLD PEAK CR-V9, EVE

CR9V/P)

Quiescent current: 6—12uA

Working Temperature: -10℃~+40℃

Alarm decibel: ≥85db/3m

Size: (diameter) 101×34mm

Dust cover included

3. Operation:

A) Remove the mounting plate from the back of the detector and insert 9V battery. CAUTION! Danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent type.).

B) Depress the test button for a few seconds for the detector to sound. When you hear the alarm sound, please release the

button (It alarms for two to three times, then stops automatically). It shows that the smoke detector is in a normal working

state ( If the alarm fails to operate correctly, the advice of the seller/manufacturer should be sought.)

C) Install the smoke detector with two pieces of screw (accessories of the detector) to the very place. (Such as roof)

D) Let the dust cover remain over the smoke alarm until the the final cleaning is completely done. Applies mainly for new

construction or renovation.

POSITIONING THE SMOKE ALARM

Ceiling Mounting

As hot smoke rises and spread out, it is advisable to mount on a ceiling in a central position. Avoid areas where there is no air

circulation. E.g. Corners of rooms and keep away from items which may prevent the free flow of air. Place the unit at least 300mm

from and light fitting or decorative object which might obstruct smoke / heat entering the alarm. Keep at least 300mm away from

walls.

Wall Mounting

Do not mount tight into the corners. Put the top edge of your smoke alarm between 150 and 300mm below the ceiling. Keep at

least 300mm from room corners.

On a Sloping Ceiling

In areas with sloping or peaked ceilings install your Smoke Alarm 900mm from the highest point measured horizontally because

“dead air” at the apex may prevent smoke from reaching the unit.

4. Points for attention:

A) No replaceable parts inside. Only battery is replaceable.

B) Do not use the product in the humid, dusty and smoky environment.

C) When the battery reached a low energy level, the detector will sound in about every 45 seconds to indicate that the

battery must be replaced.

E) Keep smoke detector and packing materials out of reach of the children.

TESTING YOUR SMOKE ALARM

It is recommended that you test your smoke alarm once a week to ensure the detector is working correctly.

Push and hold the test button for approximately 3 seconds. A loud pulsating alarm should sound to indicate the correct function.

During the alarm condition the indicator light will flash quickly.

MAINTAINING YOUR SMOKE ALARM

Clean your smoke alarm regularly to prevent dust build up. This can be done using a vacuum cleaner with the brush attachment.

Clean gently around the front grilled section and sides. Never use water, cleaners or solvents since they may damage the smoke

alarm.

5. Quality Guarantee:

Any man-made damage or improper operation of the product are not offered quality guarantee by the company.

Receipt of purchase must be presented.

You will find the Declaration of Performance (DoP) on our website

Manufacturers

Nexa Trading AB,

Sweden

www.nexa.se

Inhaltsverzeichnis

Andere Nexa Rauchmelder Handbücher

Nexa

Nexa MSA-866/10Y Handbuch

Nexa

Nexa FS-558/RF Bedienungsanleitung

Nexa

Nexa MTS-166RF Bedienungsanleitung

Nexa

Nexa GNS-2236/RF Bedienungsanleitung

Nexa

Nexa EL1313/KD-101LC Bedienungsanleitung

Nexa

Nexa KD-134A Bedienungsanleitung

Nexa

Nexa NEXA-005 Firmware-Update

Nexa

Nexa GNS-2236/RF Bedienungsanleitung

Nexa

Nexa WSA-102 Bedienungsanleitung

Nexa

Nexa GNS-2236/RF Bedienungsanleitung

Nexa

Nexa ZSD-109 Bedienungsanleitung

Nexa

Nexa FS-558/RF Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung