Nexcom EBC 580 Bedienungsanleitung

www.nexcom.com

Single Board Computer

EBC 580 Series

User’s Manual

April-12-2006 Build

Nov-15-2006 Update

Prepared by Zack

EBC 580 User’s Manual 1 Preface

Preface

This publication, including all photographs, illustrations and software, is protected under international

transmitted in any form or by any means without the prior written consent from NEXCOM International

Co., Ltd.

Version 1.0/1.1

Disclaimer

The information in this document is subject to change without prior notice and does not represent

commitment from NEXCOM International Co., LTD. However, users may update their knowledge of any

product in use by constantly checking its manual posted on our website: http://www.nexcom.com.

NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out

of the use of any product, nor for any infringements upon the rights of third parties, which may result from

such use. Any implied warranties of merchantability of fitness for any particular purpose is also

disclaimed.

Acknowledgements

The EBC 580 series is a trademark of NEXCOM international CO., LTD. All other product names

mentioned herein are registered trademarks of their respective owners.

Regulatory Compliance Statements

This section provides the FCC compliance statement for Class A devices and describes how to keep the

system CE compliant.

Federal Communications Commission (FCC) For ClassADevice

This equipment has been tested and verified to comply with the limits for a Class A digital device, pursuant

to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. Operation of this equipment in a residential area

(domestic environment) is likely to cause harmful interference, in which case the user will be required to

EBC 580 User’s Manual 2 Preface

correct the interference (take adequate measures) at their own expense.

CE Certification

The product(s) described in this manual complies with all applicable European Union (CE) directives if it

has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used.

Maintaining CE compliance also requires proper cable and cabling techniques.

WARNINGS

Read and adhere to all warnings, cautions, and notices in this guide and

the documentation supplied with the chassis, power supply, and accessory

modules. If the instructions for the chassis and power supply are inconsistent

with these instructions or the instructions for accessory modules, contact

the supplier to find out how you can ensure that your computer meets

safety and regulatory requirements.

CAUTION

Electrostatic discharge (ESD) can damage NSA components. Do the

described procedures only at an ESD workstation. If no such station is

available, you can provide some ESD protection by wearing an antistatic

wrist strap and attaching it to a metal part of the computer chassis.

Safety Information

Before installing and using the EBC 580, note the following precautions:

Read all instructions carefully.

Do not place the unit on an unstable surface, cart, or stand.

Follow all warnings and cautions in this manual.

When replacing parts, ensure that your service technician uses parts specified by the manufacturer.

Avoid using the system near water, in direct sunlight, or near a hearing device.

EBC 580 User’s Manual 3 Table of Content

Table of Content

Preface……………...……………..……………………………………….………….……..……………..1

Disclaimer………………………..………………………………..…………………………………….. 1

Acknowledgements……………………………………………..……………………………..…..…… 1

Regulatory Compliance Statements……………………..…………………………………….……………1

Federal Communications Commission (FCC) For Class A Device……………..……….…………..…..…1

CE Certification………………………………………………………………………….……….………...2

Safety Information……………………………………………………………………….………..………..2

Table of Content………………………………………………………………………………….……. 3

Chapter 1 General Information

1.1 Main Feature…………………………………………………….…………………………………….. 6

1.2 Specifications……………………………………………………..…………………………………….6

1.3 Power Consumption Measurement……………………………………………………………………..9

1.4 Board Layout…………………………………………………………………….…………………….10

1.5 Board Dimensions……………………………………………………….……………….……………12

Chapter 2Jumper Setting

2.1 Before You Begin……………………………………………..….……………………………………13

2.2 Precautions………………………………………………………………………………………...…..13

2.3 Setting Jumpers………………………………………………………………………………………..13

2.4 Location of Jumpers……………………………………………………………………………….…..15

2.5 Function of Jumper………………………….……………………………………………………........15

Chapter 3 Expansion

3.1 System Memory………………………………………………………………………………….…….26

3.2 Installing DIMM………………………………………………………………………………….. ….. 26

3.3 Installing Compact Flash………………………..…………………………………………………….. 29

EBC 580 User’s Manual 4

EBC 580 User’s Manual 5 Chapter 1

Chapter 1

General Information

EBC 580 User’s Manual 6 Chapter 1

1.1 Main Feature

Support VIA®EDEN/C7 processors from 400MHz up to 1.5GHz

•VIA® CN700 and VIA® 8237R+ chipsets

•184-pin DIMM x 1, support up to 1GB un-buffered non-ECC DDR 333/400 SDRAM

•Realtek® RTL8110SB Gigabit Ethernet Controller x 2 supporting two GbE LAN ports

•Support LVDS, CCFL, and DB-15 VGA Connector

•Support IDE and SATA HDD

•Compact Flash socket

•USB 2.0 Port x 4, COM x 4

1.2 Specifications

Figure 1.1: Block Diagram of EBC 580

System Architecture -5.25” Embedded SBC

CPU Support - Eden V4 400MHZ or 1GHZ (5W)ÎFANless Possibility

EBC 580 User’s Manual 7 Chapter 1

- C7 1.5GHZ (12W) ÎWith CPU Cooler

Memory

- 1 x 184-pin DIMM

-Up to 1GB un-buffered non-ECC DDR 333/400 SDRAM

BIOS

- Plug & Play support

- Award System BIOS

- Advanced Power Management and Advanced Configuration &

Power Interface support

Chipset

- VIA® CN700

- VIA® 8237R+

LAN - Realtek® RTL8110SB Gigabit Ethernet Controller x 2 supporting

two GbE LAN ports

Display

- LVDS1：VIA VT1636 transmitter, DF13-20DP, 20-pin connector x

2 for LVDS1 panel output

- LVDS2：VIA VT1636 transmitter, DF13-20DP, 20-pin connector x

2 for LVDS2 panel output

- CCFL：CCFL x 2 for LCD Panel Backlight Inverter Power

VGA：DB15 VGA Connector x 1

IDE - HDD: Support IDE with 44 pin connector ×1 (Secondary)

- Compact Flash Socket x 1 (Primary)

SATA - SATA x 2ports, support Raid 0,1

Audio - VIA VT1616 CODEC for AC97 v2.1 CODEC

- CD audio in, Line in

- Microphone in and Speaker out Interface

I/O Interface

- SIO×4, with 4x16C550 UARTs, COM 2 for RS 232/422/485 (40

pin 2.0 header with housing ×1)

- USB 2.0 x 4

- Parallel port: Box header 2x13 2.0mm 180-degree connector

- PS/2 connectors for Keyboard and Mouse

- Digital I/O: Pin header 2x4 2.54mm Male 180-degree connector

- IrDA：On board pin header for IrDA Tx Rx

- SMBus 2.0 controller: Pin header 1x3 2.0mm Male 180-degree

connector (One pin for GND)

- On board header for reset SW and HD active LED

- I2C: On board 3 pin header for I2C, one pin for GND

Expansion Slot

- One 32 bit/33MHZ PCI Slot support PCI Expansion.

- PCI Expansion Slot position is compatible with EBC 569. And

support NEXCOM PCI Riser Card:

EBC 580 User’s Manual 8 Chapter 1

EBK PCI1

EBK PCIR2

EBK PCIR3

I/O on Bracket

- Mic-in

- Speaker Out

- VGA DB-15 connector x 1

- RJ45 Gigabit Ethernet LAN port x 2

- USB x 2

- Mini-DIN for Keyboard/mouse x 1

System Management

- Derived from Super IO to support system monitor.

- Monitoring of 5voltages, 3temperature and 2fans Speed.

5 voltage (For +3.3V, +5V, +12V, Vcore and +2.5V)

3 Temperatures (CPU, two external Temperature Sensor)

2 FANs speed (CPU and System FANs).

- Watchdog timeout can be programmable by Software from 1

second to 64 Sec.

Real Time Clock - On-chip RTC with battery back up

- External Lithium battery x 1

Watchdog Timer - 1-minute increments from 1 to 255 minutes

- 1-second increments from 1 to 255 seconds

Dimensions - 203mm(L) x 143mm(W)

Power Supply

- Three Pin Headers for AT/ATX mode switch

- +3.3V is converted from +5V

- 6 PIN Power Input Connector

- 3 PIN Jst connector to receive the 5Vsb input from Power Source

- Factory Default Setting is AT Mode

- ATX Mode

Power Required: +12V/+5V/+5Vsb

Support Power On push Button, Software Shutdown

function and LAN1 remote wake up only.

Two Pin Header for Power On Push Button

BIOS default setting is as shown below:

¾POWER -SUPPLY TYPE Î[ATX]

¾AUTO PWR-FAILURE RESUME Î[ON]

- AT mode

Power Required: +5V/+12V

No Power On push Button, No Software Shutdown function and No

LAN1 remote wake up

EBC 580 User’s Manual 9 Chapter 1

Environments

- Board-level operating temperatures: -20°C to 60°C

- Storage temperatures: -20°C to 80°C

- Relative humidity: 10% to 90% (Non-condensing)

Certification

- CE

- FCC Class A

Ordering Information

EBC 580-715

RoHS Compliant. 5.25” Low Power Embedded Board with VIA C7 CPU 1.5G

w/VGA/ Dual LVDS/Audio/4 COMs/8 USB2.0 /Dual Gigabit LAN

EBC 580-E10

RoHS Compliant. 5.25” Low Power Embedded Board with VIA Eden V4 Bus CPU

1GHZ w/VGA/ Dual LVDS/Audio/4 COMs/8 USB2.0 /Dual Gigabit LAN

1.3 Power Consumption Measurement

EBC-580-715 Power Consumption

PowerType +12V +5V +5VSB Mode

Power-On 0.81A 2.70A x AT Mode

HCT 1.30A 2.80A 0.28A ATX Mode

EBC-580-E10 Power Consumption

PowerType +12V +5V +5VSB Mode

Power-On 0.46A 2.71A x AT Mode

HCT 0.39A 2.59A 0.04A ATX Mode

Inhaltsverzeichnis

Andere Nexcom Hauptplatine Handbücher

Nexcom

Nexcom PEAK 7220VL2G Bedienungsanleitung

Nexcom

Nexcom COM Express Type 6 ICES 673 Bedienungsanleitung

Nexcom

Nexcom NEX 650 Bedienungsanleitung

Nexcom

Nexcom NSA 7141 Bedienungsanleitung

Nexcom

Nexcom PEAK 887VL2 Bedienungsanleitung

Nexcom

Nexcom ICES 675 Bedienungsanleitung

Nexcom

Nexcom NEX 605 Bedienungsanleitung

Nexcom

Nexcom NEX 650-ADU Bedienungsanleitung

Nexcom

Nexcom PEAK 886VL2 Bedienungsanleitung

Nexcom

Nexcom PEAK650VL2B Bedienungsanleitung

Nexcom

Nexcom ICES 670 Series Bedienungsanleitung

Nexcom

Nexcom NEX 812 Bedienungsanleitung

Nexcom

Nexcom NEX 812 Bedienungsanleitung

Nexcom

Nexcom EBC575 Series Bedienungsanleitung

Nexcom

Nexcom 912P Bedienungsanleitung

Nexcom

Nexcom NISB 60 Bedienungsanleitung

Nexcom

Nexcom NSA 3180A Bedienungsanleitung

Nexcom

Nexcom PEAK 886 Bedienungsanleitung

Nexcom

Nexcom NEX 609 Bedienungsanleitung

Nexcom

Nexcom Neu-X300-H310 Bedienungsanleitung

Nexcom

Nexcom EBC 357X Bedienungsanleitung

Nexcom

Nexcom NSA 7141 Bedienungsanleitung

Nexcom

Nexcom EBC 300 Series Bedienungsanleitung

Nexcom

Nexcom EBC 354 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung