TRIPOD SETUP
1. Unlatch the top release lever to loosen.
Slide the top portion to desired height and
lock into place.
2. Unlatch the bottom release lever to loosen.
Slide the bottom portion to desired height
and lock into place
Tips & Tricks: If the latch is too loose or
too tight, we have designed a standard
Philips screw allowing you to slightly tighten
or loosen the latch locking tension to your
desired setting.
3. To set up legs, simply pull each of the three
legs downward, until they automatically lock into place.
4. Unlatch the top release lever to loosen the top bar. Now, the
top tripod bar is fully rotatable for 360 degree LED positioning,
without needing to move the legs
TRIPOD STORAGE
1. Unlatch the top release lever to loosen. Slide
the top portion downwards fully closing the
top portion of the unit.
2. Unlatch the bottom release lever to loosen.
Slide the bottom portion downwards fully
closing the bottom portion of the unit.
3. To fold up the legs, simply slide the release
lever downwards to unlock the pin that is
holding the leg in place. While sliding the
release lever down, begin pulling up on the
leg to fold it all the way upwards until snug.
Tips & Tricks: Our legs are designed for stability and you may
need to gently pull up or down on the leg to align and disengage
the locking pin. If you pull too hard the pin could be damaged
and not algin properly.
REMOVEABLE LED HEAD
The LED head can screw off at the top by
simply rotating the head unit. Once loosened
the head will simply lift off.
1. Once it is detached the LED head can sit
on the ground or can be attached to any
metalic surface because it comes equipped
with 4 strong magnets that are attached to
the base of the LED head.
2. When removed from the tripod, the LED
head also has a convenient drop-down
hanging loop that adds additional
functionality to your work light.
3. The LED head comes standard with a
protective dust cap, covering the charging plug interface.
BATTERY CHARGING
1. Remove the protective dust cap, then connect the power cord
adapter into the underside of the LED, where pin adapter inserts.
Tips & Tricks:
To Insert: you must fully insert the power cord adapter until you
hear an audible click to let you know it is fully inserted.
To Remove: Turn the power cord adapter counterclockwise to
unlock and remove from the unit.
2. Connect the plug end of the charger into
an electric outlet.
3. LED lights will work while charging.
Battery Charging Indicating:
The two left green LED’s on the control panel indicate battery status.
When fully charged, both green LED’s are solid green. Only the left
LED will be lit solid when charge is below 50%. The left LED will
flash when power is below 10%
While charging, the left LED will flash when charge is below 50%.
Above 50%, the left LED will be solid and the right LED will flash.
When fully charged, both LED’s will be lit solid.
WARNING! Charge while indoors only.
WARNING! Always use the 8.4v / 3A charging cable and adapter
that came standard with your unit
Using a non-compatible charger could cause damage to the work
light or personal injury.
Your product, accessories and packaging should be discarded in an
environmentally responsible way.
Illustrations, figures and photos may vary slightly due to our program
of continuous product improvements.
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
ONE YEAR LIMITED WARRANTY
If this NextLED®product fails due to defect in materials or
workmanship, NextLED®will at its option, repair it or replace it
with the same or comparable model, free of charge.
For repair or replacement under warranty, return to the retail
establishment where the product was purchased.
This warranty give you specific legal rights and you may have
other rights that vary from state to state.
This warranty is void if damage or defect has resulted from accident,
abuse, misuse or faulty repair. In no event will NextLED®be liable for
any consequential, special, incidental, or indirect damages of any
kind arising out of the use or misuse of this product.
Maximum liability shall not in any case exceed the purchase price
of the product including shipping. Some states do not allow the
exclusion or limitation of incidental or consequential damages so the
above exclusions or limitations may not apply to you.
© 2022 Distributed by Nextool Inc.
Schaumburg, IL
Visit www.mynextled.com
Customer Service: 1-877-886-6822
MADE IN CHINA
SPECIFICATIONS
LED’s: ..........................Two Illumination settings:
White & Daylight) SAMSUNG 2828
White & Daylight)
Max. Brightness ..........6,000 Lumens (High)
(Battery): 2,000 Lumens (Medium)
500 Lumens (Low)
Max. Brightness .........1,800 Lumens
(Corded):
Runtime: ......................2 hr. (High) / 5 hrs. (Medium)/ 10 hrs (Low)
by fully charged battery
Battery Size: ................Four rechargeable Lithium-Ion
Batteries included; 7.4v 8000 mAh
Functions 2 ways: .......cordless with batteries and also
works while plugged into an outlet.
Charger:.......................8.4V / 3A
Rechargeable
Charging Cable ...........Included
Charging time: .............8 hrs (Charger: 8.4V / 3A)
Net Weight:..................9.9 lbs.
Tripod fully extends to 75.5” and folds down to just 35”
Scan to register
your product
Simply scan and
register your product
for warranty or visit
www.mynextled.com.
