NexxTech 4313385 Bedienungsanleitung

MEMO

NEW

CALL#

REPEAT

OWNERʼS MANUAL —

Please read before using this equipment.

DIGITAL ANSWERER WITH CID

4313385

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always

be followed to reduce the risk of fire, electric shock and injury to persons,

including the following:

1. Do not use this product near water, for example, near a bath tub, wash

bowl, kitchen sink or laundry tub, in a wet basement or near a swimming

pool.

2. Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not

dispose of batteries in a fire. They may explode. Check with local codes

for possible special disposal instructions.

5. Position the equipment near an electrical outlet that shall be easily

accessible and plug the adapter into the outlet.

SAVE THESE INSTRUCTIONS!

INDUSTRY CANADA CS03 STATEMENT

This product meets the applicable Industry Canada technical specifications.

This is confirmed by the registration number. The abbreviation, IC before the

registration number signifies that registration was performed based on a

Declaration of Conformity indicating that Industry Canada technical

specifications were met. It does not imply that Industry Canada approved the

equipment.

Before installing this equipment, users should ensure that it is permissible to

be connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connections.

The customer should be aware that compliance with the above conditions

may not prevent degradation of service in some situations. Repairs to certified

equipment should be made by an authorized Canadian maintenance facility

designated by the supplier. Any repairs or alterations made by the user of this

equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

WARNING! Users should not attempt to make such connections themselves,

but should contact the appropriate electric inspection authority, or an electrician,

as appropriate.

CAUTION: The Ringer Equivalence Number (REN) assigned to each terminal

device provides an indication of the maximum number of terminals allowed to

be connected to a telephone interface. The termination on an interface may

consist of any combination of devices subject only to the requirement that the

sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

An alternative indication of the REN is the Load Number (LN); this number

should be divided by 20 to approximate the equivalent REN. The REN Number

of this unit is indicated on the bottom of your answering machine.

INDUSTRY CANADA RSS 210 NOTICE:

CLASS B LIMITS WITH INTERFERENCE

STATEMENT

This equipment complies with the limits of a Class B digital device as specified

in Industry Canada Regulations.

These limits provide reasonable protection against radio and TV interference

in residential areas. However, this device might cause radio or TV interference

even when it is operating properly.

Operation is subject to the following two conditions: (1) This device may not

cause interference, and (2) this device must accept any interference including

interference that may cause undesired operation of the device.

To eliminate the interference, you can try one or more of the following:

• Reorient or relocate the receiving antenna.

• Move your device away from the receiver.

• Connect your device to an outlet that is on a different electrical circuit

from the receiver.

This digital apparatus does not exceed the Class B limits for radio noise

emissions from digital apparatus.

BATTERY NOTES

Dispose of old battery promptly and properly.

Do not burn or bury battery.

Use only fresh battery of the required size and recommended type.

If you do not plan to use the phone for two weeks or longer, remove the

battery. Batteries can leak chemicals that can destroy electronic parts.

To avoid losing stored information, be sure the system is properly connected

to AC power before you replace the battery.

Disconnect the telephone line cord before replacing the battery to reduce

the risk of fire or injury.

1. Line Cord

2. Incoming Message Length

Switch

3. Call Back Button

4. Display

5. Erase Button

6. Microphone

7. Volume Button

8. / OGM Button

9. Play / Pause button

10. Menu Button

11. Delete Button

12. Ringer Switch

13. Power Jack

14. Telephone Line Jack

15. New Call LED

16. Review Button

17. Review Button

18. Speaker

19. Message LED

20. / Time Check Button

21. Memo / 2 way Button

22. On / Off / Stop Button

23. Volume Button

INSTALLATION

TO INSTALL 9-VOLT BATTERY

In the event of a power failure, a 9V alkaline battery (not supplied) is required

to maintain your personalized outgoing announcement, recorded messages

and CID data. If the battery is not installed, all your personalized outgoing

announcement, recorded messages and CID data will be lost.

To install battery

1. Use a flat-blade screwdriver to lift up the battery compartment cover, and

then remove the cover.

2. Attach a 9V alkaline battery to the terminals and place the battery in the

compartment.

3. Replace and snap the cover into place.

Note: This unit will signal you when the battery becomes weak and needs

replacement. Once battery power has been sufficiently drained, the icon

will illuminate on the LCD. Replace the 9V battery with a fresh one.

CONNECTING AC POWER

1. Insert the AC adapter’s plug into the power jack on the back of the unit.

2. Plug the adapter into a standard AC outlet.

After power up, your unit will need approx. 40 seconds to initialize all the

functions (the LCD will show ‘INITIALIZATIONINITIALIZATION

INITIALIZATIONINITIALIZATION

INITIALIZATION’) . After the first

initialization, the LCD will show ‘LANGUAGELANGUAGE

LANGUAGELANGUAGE

LANGUAGE’. Now you can setup your

unit (see “Setting UpYour Unit”) or the unit will show‘CALLS:00 NEW:00CALLS:00 NEW:00

CALLS:00 NEW:00CALLS:00 NEW:00

CALLS:00 NEW:00’

after initialization.

PREPARATION

SETTING UP YOUR UNIT

DO NOT CONNECT the line cord to the wall outlet until the setup has been

completed.

To set the language

The LCD shows ‘LANGUAGELANGUAGE

LANGUAGELANGUAGE

LANGUAGE’. If your LCD does not, press and hold MENU

button for 2 seconds.

Press CALL BACK button, the LCD then shows ‘FRA ENGFRA ENG

FRA ENGFRA ENG

FRA ENG’.

Note: The ‘ENGENG

ENGENG

ENG’ is blinking. Press REVIEW or button to select ‘FRAFRA

FRAFRA

FRA’, or

‘ENGENG

ENGENG

ENG’. Press CALL BACK button to confirm.

To set the LCD contrast

Once ENGENG

ENGENG

ENG is selected, the LCD shows ‘LCD CONTRASTLCD CONTRAST

LCD CONTRASTLCD CONTRAST

LCD CONTRAST’.

Press CALL BACK button, the digit ‘3’ blinks.

Press REVIEW or button to adjust the level of contrast of LCD (from 1 to

5, default is 3).

Press CALL BACK button to confirm.

To set the weekday

Once contrast is set, the LCD shows ‘ENTER WEEKENTER WEEK

ENTER WEEKENTER WEEK

ENTER WEEK’.

Press CALL BACK button, the LCD shows ‘SUNDAYSUNDAY

SUNDAYSUNDAY

SUNDAY’ and the unit announces

the weekday.

Press REVIEW or button to set the correct weekday.

Press CALL BACK button, the unit announces the weekday set and the LCD

then shows ‘ENTER TIMEENTER TIME

ENTER TIMEENTER TIME

ENTER TIME’.

To set the time

Press CALL BACK button, the hour digits blink and the unit announces the

hour.

Press REVIEW or button to set the correct hour.

Press CALL BACK button, the minute digits blink and the unit announces the

minute.

Press REVIEW or button to set the correct minutes.

Press CALL BACK button to confirm. The unit announces the time set and

the LCD then shows ‘ENTER DATEENTER DATE

ENTER DATEENTER DATE

ENTER DATE’.

To set the date

Press CALL BACK button, the month digits blink.

Press REVIEW or button to set the correct month.

Press CALL BACK button, the day digits blink.

Press REVIEW or button to set the correct day.

Press CALL BACK button to confirm.

To set the area code

Once time and date are set, the LCD shows ‘SET AREA CODESET AREA CODE

SET AREA CODESET AREA CODE

SET AREA CODE’.

Press CALL BACK button, the first digit ‘–’ of the area code blinks.

Press REVIEW or button to enter the first digit. Press CALL BACK button

to confirm and go to next entry.

Repeat above steps until the 3-digit area code is set.

After you press CALL BACK button to confirm the third digit, the unit returns

to standby mode at once.

This procedure has now been completed, you should see all the current data

you entered on the LCD.

Notes:

• Press ERASE button to exit a menu at any time.

• To check the time and date, just press the / TIME CHECK button. The

unit will announce the current time.

• If there is a delay of 30 seconds between any of the steps, the unit will

revert to standby mode.

CONNECTING THE TELEPHONE LINE

1. Plug the telephone line cord from the unit into the wall jack.

2. Plug your phone’s line cord (not supplied) into the TEL. LINE jack.

TURNING THE UNIT ON/OFF

To turn on the unit, press ON/OFF/STOP button.The message LED illuminates

and the unit is set to answer calls.

To turn it off, press ON/OFF/STOP button. The message LED turns off.

RECORDING OUTGOING MESSAGES (OGM)

For your outgoing message, you can either use prerecorded outgoing message

or you can record your own outgoing message. If you do not record a message

of your own, the prerecorded outgoing message will be used automatically.

Wording of the prerecorded outgoing message:‘

Hello, please leave a message

after the tone

’.

To record your own OGM (up to 5 minutes):

1. Press and hold / OGM button and the unit beeps. The LCD shows

‘OGM RECORDING’ and the counter starts counting up.

2. Speak clearly at a distance of about 15 cm (6 inches) from the microphone.

3. Release the / OGM button when you have finished speaking. Your

OGM will be played back automatically and the LCD shows ‘OGM

PLAYBACK’.

Notes:

• To change your OGM, repeat steps 1-3 above.

• Each outgoing message can be recorded, played back, or deleted

independently.

• The length of your message will reduce the total recording time available

for incoming calls. For example, a 20-second message will leave

approximately 49 minutes and 40 seconds recording time.

• To check your OGM at any time, press and release the / OGM button.

• If you record your own message and subsequently decide to use the

prerecorded message, press / OGM button. While your own message

is playing, press DELETE button.

SETTING THE NUMBER OF RINGS

To control the duration before the unit answers a call, slide the switch on the

rear side of the unit to the desired number of rings (2, 6,or TS).

TS (Toll Saver) – If you choose the Toll Saver option, and there are new

messages, the unit answers after two rings. Otherwise, the unit answers after

six rings.This lets you avoid unnecessary charges when calling by long distance

to check your messages. If you hear more than two rings, you know you can

hang up because the unit has no new messages.

SETTING THE INCOMING MESSAGE LENGTH

Set the slide switch on the rear side of the unit to 1 or 5 MIN (minutes) to

choose the length of incoming messages. After the caller hangs up or is silent

for more than 7 seconds, or the maximum message length is reached, the unit

hangs up and resets to answer the next call.

ANSWERING SYSTEM OPERATION

RECORDING A MEMO

A memo is a message that you record by speaking directly into the unit, without

calling in on the phone.

1. Press and hold MEMO/2 WAY button and the unit beeps. The LCD shows

‘MEMO RECORDINGMEMO RECORDING

MEMO RECORDINGMEMO RECORDING

MEMO RECORDING’ and the counter starts counting up.

2. Speak clearly at a distance of about 15 cm (6 inches) from the microphone.

3. Release the MEMO/2 WAY button when you have finished speaking. The

MEMO icon will be lit on the LCD.

RECORDING A 2-WAY PHONE CONVERSATION

You can record both sides of a conversation on any phone connected to the

same phone line as the unit.

At any time during the conversation, press MEMO/2 WAY button. The LCD

shows ‘2-WAY RECORDING2-WAY RECORDING

2-WAY RECORDING2-WAY RECORDING

2-WAY RECORDING’ and the counter starts counting up to indicate

the unit is recording the call. Press MEMO/2 WAY button again to stop recording.

PLAYING MESSAGES

The Message LED flashes after the unit records new messages, recorded

memos, or two-way phone conversations.

1. To listen to all messages, memos, and two-way conversations, press PLAY/

PAUSE button. The unit plays each new message in sequence and

announces the date and time it was recorded.

2. During message playback:

• Press / OGM button to repeat the current message.

• Press and hold / OGM button until your hear a beep to repeat the

previous message.

• Press / TIME CHECK button to skip forward to the next message.

• Press / TIME CHECK button several times in succession to skip

multiple messages.

• Press PLAY/PAUSE button to pause, press PLAY/PAUSE button again

to resume.

• To stop message playback, press ON/OFF/STOP button.

3. After playing all messages, the unit sounds a beep and then returns to

answer-ready mode. The Message LED lights solid and all messages are

saved.

To replay the messages, press PLAY/PAUSE button.

DELETING MESSAGES

You can delete messages individually during playback, or all at once after

playback.

To delete an incoming message, memo, or two-way phone conversation (after

listening to it),

press DELETE button during playback.

To delete all messages after playback,

hold down DELETE button until you

hear a beep.

Note: You cannot delete the messages until you play them all back.

ADJUSTING THE SPEAKER VOLUME

Press button to increase the volume, or button to decrease the volume.

SCREENING CALLS

To screen your calls, let the unit answer. Listen to the callerʼs message through

the unitʼs speaker. If you decide to answer the call, pick up any phone connected

to the same phone line as the unit. The unit stops recording and resets to

answer the next call.

MEMORY FULL

If memory is full, the unit cannot record new messages until you delete the old

messages. See “Deleting Messages” section.

The unit will answer calls after 10 rings and you will hear an announcement of

“Memory is full”. If the 3-digit security code has not been entered within 10

seconds, the unit will hang up.

Note: The maximum recording memory of your answering system is

approximately 50 minutes.

CALLER ID OPERATION

Caller ID is a service provided by your telephone company. When you subscribe

to this service, the telephone company sends the callerʼs telephone number

(and name, if available) and the callʼs date and time. This unit receives and

displays this information for each call. This unit saves up to 64 Caller ID records,

then replaces the oldest Caller ID record with each new one.

RECEIVING CALLS

During an incoming call, NEW appears and the New Call LED blinks while the

phone is ringing. The number of new and total calls appear. The New Call LED

blinks until all the new calls have been reviewed.

•

If only the callerʼs phone number is received,

the callerʼs phone number

with the call time and date appear.

•

If an incorrect, invalid or incomplete signal is received,

ʻLINE ERRORʼ

appears.

•

If the name and number are unlisted,

ʻPRIVATEʼ appears with the call

time and date.

•

If the name and number are not available,

ʻUNAVAILABLEʼ appears with

the call time and date.

If no key is pressed within 30 seconds, the LCD will return to standby mode,

and display the total call counter, new call counter, current time and date.

REVIEWING CALLER ID RECORDS

Each Caller ID record includes the time and date of the call, the call number

(determined by the order in which the calls are received), the callerʼs telephone

number, and the callerʼs name (if available).

1. Press REVIEW button to review the latest number, or press REVIEW

button to review the oldest number.

After you view all the calls in memory, ʻEND OF LISTʼ appears and the

New Call LED turns off.

2. To view them again, press REVIEW or button.

Note: REPEAT appears if you receive more than one call from the same

number.

DELETING CALLER ID RECORDS

Deleting a single record

1. Press REVIEW or button until you see the record you want to delete.

2. Press ERASE button once. ʻERASE?ʼ appears.

3. Hold down the ERASE button until ʻERASEDʼ appears. The remaining

Caller ID records are renumbered automatically.

Deleting all records

1. After reviewing all new messages, press and hold down the ʻERASEʼ

button until the ʻERASE ALL?ʼ appears.

2. Release the ʻERASEʼ button and press it again while ʻERASE ALL?ʼ is

still on the display until ʻALL ERASEDʼ appears.

Note: You must review all new calls before you can erase all calls.

BACKLIT DISPLAY

When you receive a call or press any key, the LCD will light up. It will turn off

after approx. 7 seconds when no key is pressed.

CALL BACK FROM THE CALLER ID MEMORY

1. Press REVIEW or button to find the Caller ID memory location to be

redialed.

2. Press CALL BACK button, the 7-digit number (if same area code) or

11-digit number (if different area code) will blink.

3. Press REVIEW or button to select one of the options.

4. Press CALL BACK button, the LCD shows ʻDIALING...ʼ and the phone

number to be dialed immediately. The LCD then shows ʻPICK UP

HANDSETʼ.

Note: If you pick up the handset before pressing the CALL BACK button,

ʻREPLACE HANDSETʼ will appear. Replace the handset then the number

will be redialed and ʻPICK UP HANDSETʼ will appear.

5. Pick up the handset on the telephone connected to the same telephone

line as the unit for conversation.

When the callerʼs phone number has a different area code from

the preset:

The long distance dialing digit ʻ1ʼ will be inserted automatically during Caller

ID memory call back.

Press CALL BACK button, 11-digit number will blink. Press CALL BACK button

again to confirm to dial the 11-digit number.

When the callerʼs phone number has the same area code as the

preset:

The long distance dialing digit ʻ1ʼ and the 3-digit area code will be deleted

automatically during Caller ID memory call back.

Press CALL BACK button, 7-digit number will blink. Press CALL BACK button

again to confirm to dial the 7-digit number.

Note: Your telephone company may require a different format for making out-

of-area (toll) calls WITHIN your area code. See the next section for the

procedure to obtain the applicable toll-call format for your phone company.

When your telephone company requires you to dial other than a 7-digit number

(same area code) or 11-digit number (different area code) to make toll calls

within your area code, follow one of the four options below for Caller ID call

back.

Option 1

1+Area Code+7-Digit Number (11 digits)

Option 2

1+7-Digit Number (8 digits)

Option 3

Area Code+7-Digit Number (10 digits)

Option 4

7-Digit Number Only.

Follow the procedure below to select one of the four options for Caller ID call

back.

With the handset hung up on the base.

1. Press REVIEW or button to find the Caller ID memory location to

redial. Press CALL BACK button, the 7-digit number (if same area code)

or 11-digit number (if different area code) will blink.

2. Press REVIEW or button to select one of the options.

3. Press CALL BACK button again to confirm the dial. The LCD shows

ʻDIALING...ʼ. The selected number is dialed automatically and then

the LCD shows ʻPICK UP HANDSETʼ.

REMOTE OPERATION

While you are away from your home or office, you can access your unit by

remote operation. Use a touch-tone phone to enter your remote operation

security code.

OPERATING THE SYSTEM FROM A REMOTE

LOCATION

To use your unit from a remote telephone, you must first enter a 3-digit remote

operation security code. The security code label is located on the bottom of

the unit.

1. Dial your phone number.

2. When your outgoing message is playing, enter your remote operation

security code.

3. Two beeps will confirm that the right code has been entered. Now select

one of the remote commands. If no key is pressed for 10 seconds, the

unit will hang up.

Press: To:

1# Playback new messages

2# Playback all recorded messages

7# Turn on/off the unit

8# Re-record an OGM

(press 5# to stop recording)

9# Record a memo

(press 5# to stop recording)

0# Room monitoring

5# Stop room monitoring

When you press 1# to playback new messages, or 2# to play all

messages, you can then press the following keys to get these remote

functions.

Press: To:

3# Delete current message

4# Repeat previous messages

5# Stop playback

6# Skip current message

4. After all your messages have been played, you hear two short beeps. You

have 10 seconds to access the menu again, otherwise, the unit disconnects

automatically.

REMOTE TURN ON

If you forget to turn your unit on, you can phone in from a remote location and

turn it on automatically.

1. Call your telephone number.

2. The unit answers after 10 rings. You will hear an announcement ʻNo one is

available to take your call. After several beeps, enter your 3-digit security

code.

3. After the second beep, press 7# then hang up. Subsequent messages

will be recorded.

REMOTE RECORD NEW OGM

If you press 8# (to record new OGM):

1. When you hear a beep, begin recording your new OGM (up to 5 minutes).

2. When you have finished recording your new OGM, press 5# . The new

OGM will playback to you.

3. Hang up the telephone.

REMOTE RECORD MEMO

If you press 9# (to record memo):

1. When you hear a beep, begin recording your memo.

2. When you have finished recording your memo message, press 5# .

ROOM MONITORING

If you press 0# (to room monitoring):

1. The built-in microphone of your answering machine will be switched on

and you can them listen in on the room.

2. Every 30 seconds you will hear a beep. If you want to continue listening,

press 0# again within 10 seconds. Otherwise the unit will hang up.

3. To end room monitoring, hang up the telephone or press 5# if you want to

use other remote functions.

TO RETRIEVE MESSAGES WHEN RECORDING

MEMORY IS FULL

1. When the message capacity is full, the unit will answer your call after 10

rings and announces ʻMemory is fullʼ.

2. Enter your 3-digit security code.

3. Follow the remote message playback procedure. After all the messages

have been played back, delete ones or all of them to create more memory

space.

SURGE PROTECTION

Your answering system with Caller ID has built-in protection circuits to reduce

the risk of damage from surges in telephone line and power line current.

However, lightning striking the telephone or power lines can damage your

telephone.

Lightning damage is not common. Nevertheless, if you live in an area that has

severe electrical storms, we suggest that you unplug your phone when storms

approach to reduce the possibility of damage.

SET-UP

Your answering system with Caller ID connects directly to a modular telephone

line jack. If your telephone wiring does not have a modular jack, you can

update the wiring yourself using jacks and adapters, or have the telephone

company update the wiring for you.

Note: The CSA number of the jack to be installed is CA11C (or CA11W for a

wall plate jack).

If your home has specially wired alarm equipment connected to the telephone

line, be sure that installing the telephone does not disable your alarm

equipment. If you have questions about what will disable your alarm equipment,

contact your telephone company or a qualified installer.

CARE/SERVICE AND REPAIR

Keep your answering system with Caller ID dry; if it gets wet, wipe it dry

immediately. Use and store your answering system with Caller ID in room

temperature environments only. Handle your answering system with Caller ID

carefully; do not drop it. Keep your answering system with Caller ID away from

dust and dirt, and wipe it with a damp cloth occasionally to keep it looking

new.

Modifying or tampering with the telephoneʼs internal components can cause a

malfunction and might invalidate its warranty.

LIMITED WARRANTY

Who is Providing This Warranty?

• Orbyx Electronics, LLC (“Orbyx"), as the distributor of this Nexxtech™ product (your

“Product”).

What Does This Warranty Cover?

• This warranty covers defects in materials or workmanship in your Product under normal use

and conditions.

What is the Period of Coverage?

• This warranty covers your Product for 12 months from the original purchase date.

Who Is Covered?

• This warranty covers the original consumer purchaser. Coverage terminates if you sell or

otherwise transfer your Product.

What Will We Do To Correct Problems?

• We will repair your Product or replace your Product with a new or reconditioned equivalent

product, at our option.

How Do You Get Service?

• Call Orbyx TOLL FREE at 1-866-363-3059 for instructions for obtaining warranty service

from Orbyx’s authorized service providers.

• Or, return your Product directly to the retail store from which you purchased the Product.

• When you obtain service for your Product, you must provide a purchase receipt (or other

proof of the original purchase date) and a description of the defect(s).

What Does This Warranty Not Cover?

• This warranty DOES NOT COVER:

• damage due to misuse, abuse, alteration, unauthorized repair, or accident (such as

improper electrical current);

• damage due to “acts of God” (such as lightning) or other contingencies beyond our control;

• cosmetic damage;

• externally generated static, signal reception or antenna problems not caused by your

Product; or batteries.

• This warranty also DOES NOT COVER, and in no case will we be liable for, any incidental

damages (such as transportation costs to and from an authorized service provider, or loss of

time) or consequential damages (such as costs of repairing or replacing other property

which is damaged, including tapes, discs, speakers not included with your Product or other

accessories, or external electrical systems) resulting from the use of your Product. Some

states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you.

• Defacing the serial number, or using your Product for commercial or institutional purposes,

voids this warranty.

Are There Other Warranties?

• There are no express warranties other than those expressed herein. Neither the sales

personnel nor any other person is authorized to make any other warranties or to extend the

duration of any warranties.

• ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY (AN UNWRITTEN WARRANTY THAT A PRODUCT IS FIT FOR

ORDINARY USE), ARE LIMITED TO 90 DAYS. Some states do not allow limitations on

how long an implied warranty lasts, so the above limitation may not apply to you.

How Does State Law Apply?

• This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

ORBYX ELECTRONICS WARRANTY

ORBYX Electronics warrants that this product will be free from defects in materials and

workmanship for a period of one (1) year from the date of purchase. Within this period, simply

take the product and your proof of purchase to any ORBYX Electronics store or dealer and the

product will be repaired without charge for parts and labour. ORBYX Electronics reserves the

right to charge for transportation. Any product which has been subject to misuse or accidental

damage is excluded from this warranty.

This warranty is only applicable to a product purchased through ORBYX Electronics' company

owned stores and dealers and to a product that is presented for repair in a country where

ORBYX Electronics offers the product for sale. While this warranty does not confer any legal

rights other than those set out above, you may have additional statutory rights which will vary

under the laws of the various countries, states, province and other governmental entities in

which ORBYX Electronics operates. This warranty is subject to all statutory rights you may have

in the country of purchase.

LIMITED WARRANTY

Limited Warranty/Garantie Limitée

U.S.A & Canada

Distributed exclusively in the U.S. by

Orbyx Electronics, LLC

501 South Cheryl Lane,

Walnut, CA 91789

Imported in Canada for/Importé au Canada pour

Orbyx Electronics,

Concord, Canada, L4K 4M3

Manufactured in China

For product support please contact www.orbyxelectronics.com or

1-866-363-3059

2LMB86YY

Inhaltsverzeichnis

Andere NexxTech Anrufbeantworter Handbücher

NexxTech

NexxTech 4313386 Bedienungsanleitung

Beliebte Anrufbeantworter Handbücher anderer Marken

Radio Shack

Radio Shack TAD-795 Bedienungsanleitung

AT&T

AT&T 2455 Bedienungsanleitung

Panasonic

Panasonic KX-TG2583CB Bedienungsanleitung

Panasonic

Panasonic KX-TGE820E Bedienungsanleitung

BellSouth

BellSouth GH9488 Sicherheitsleitfaden

GE 2-9985 Bedienungsanleitung

Panasonic

Panasonic KX-TG2631 Bedienungsanleitung

Panasonic

Panasonic KX-TCD961CXB Bedienungsanleitung

Krown

Krown PortaPrinter 2000STD Bedienungsanleitung

AT&T

AT&T 1717 Bedienungsanleitung

Alcatel

Alcatel TEMPORIS 55-CE Bedienungsanleitung

AT&T

AT&T E2562 Bedienungsanleitung

Telstra

Telstra Monitor 420 Bedienungsanleitung

Kortex

Kortex IAM V90 Bedienungsanleitung

Panasonic

Panasonic EASA-PHONE KX-T1451 Bedienungsanleitung

Philips

Philips VOIP8551B/05 Bedienungsanleitung

Topcom

Topcom LUCCA Answering Machine Bedienungsanleitung

Panasonic

Panasonic KX-TGM420 Bedienungsanleitung