NI NI-9154 Bedienungsanleitung

NI-9154 Getting

Started

2022-07-06

Contents

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Guidelines for Hazardous Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

What You Need to Install the NI-9154. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installing C Series Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Removing C Series Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting the NI 9154 to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting One or More NI-9154 Chassis to the MXI-Express Host System or a Target.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Wiring Power to the Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Chassis Powerup Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Checking MXI-Express LINK LEDs for Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Powering Down the MXI-Express System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Where to Go Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

NI Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

ni.com

NI-9154 Getting Started

Overview

This document describes how to begin using the NI-9154.

Safety Guidelines

Caution Observe all instructions and cautions in the user documentation.

Using the model in a manner not specified can damage the model and

compromise the built-in safety protection. Return damaged models to NI

for repair.

Attention Suivez toutes les instructions et respectez toutes les mises

en garde de la documentation utilisateur. L'utilisation d'un modèle de

toute autre façon que celle spécifiée risque de l'endommager et de

compromettre la protection de sécurité intégrée. Renvoyez les modèles

endommagés à NI pour réparation.

NI-9154 Getting Started

Safety Guidelines for Hazardous Locations

The NI-9154 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous

locations; Class I, Zone 2, AEx nA IIC T4 Gc and Ex nA IIC T4 Gc hazardous locations;

and nonhazardous locations only. Follow these guidelines if you are installing the

NI-9154 in a potentially explosive environment. Not following these guidelines may

result in serious injury or death.

Caution Do not disconnect the power supply wires and connectors from

the controller unless power has been switched o.

Caution Do not disconnect I/O-side wires or connectors unless power has

been switched o or the area is known to be nonhazardous.

Caution Do not remove modules unless power has been switched o or

the area is known to be nonhazardous.

Caution Substitution of components may impair suitability for Class I,

Division 2, or Zone 2.

Caution The system must be installed in an enclosure certified for the

intended hazardous (classified) location, having a tool secured cover/door,

where a minimum protection of at least IP54 is provided.

Special Conditions for Hazardous Locations Use in Europe and

Internationally

The NI-9154 has been evaluated as Ex nA IIC T4 Gc equipment under

DEMKO 12ATEX 1202658X and is IECEx UL 14.0089X certified. Each device is marked

II 3G and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of 0 °C ≤ Ta ≤ 55 °C.

ni.com

NI-9154 Getting Started

Caution Transient protection shall be provided that is set at a level not

exceeding 140% of the peak rated voltage value of 85 V at the supply

terminals to the equipment.

Caution The system shall only be used in an area of not more than

Pollution Degree 2, as defined in IEC/EN 60664-1.

Caution The system shall be mounted in an ATEX/IECEx-certified

enclosure with a minimum ingress protection rating of at least IP54 as

defined in IEC/EN 60079-15.

Caution The enclosure must have a door or cover accessible only by the

use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits

for electromagnetic compatibility (EMC) stated in the product specifications. These

requirements and limits provide reasonable protection against harmful interference

when the product is operated in the intended operational electromagnetic

environment.

This product is intended for use in industrial locations. However, harmful

interference may occur in some installations, when the product is connected to a

peripheral device or test object, or if the product is used in residential or

commercial areas. To minimize interference with radio and television reception and

prevent unacceptable performance degradation, install and use this product in strict

accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved

by National Instruments could void your authority to operate it under your local

regulatory rules.

NI-9154 Getting Started

Special Conditions for Marine Applications

Some products are approved for marine (shipboard) applications. To verify marine

approval certification for a product, visit ni.com/product-certifications, search by

model number, and click the appropriate link.

Notice In order to meet the EMC requirements for marine applications,

install the product in a shielded enclosure with shielded and/or filtered

power and input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes and cables to

ensure that the desired EMC performance is attained.

Preparing the Environment

Ensure that the environment in which you are using the NI-9154 meets the following

specifications.

Operating temperature (IEC 60068-2-1, IEC 60068-2-2) 0 °C to 55 °C

Operating humidity (IEC 60068-2-78) 10% RH to 90% RH, noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

Indoor use only.

Note Refer to the device specifications on ni.com/manuals for complete

specifications.

What You Need to Install the NI-9154

■ NI-9154 reconfigurable embedded chassis with integrated MXI-Express (x1)

■One of the following MXI-Express (x1) host systems:

■PXI system with MXI-Express device installed

■PC with MXI-Express PCI or PCIe device installed

■NI Industrial Controller

ni.com

NI-9154 Getting Started

■ NI cRIO-9081/9082 integrated system

Note

The NI-9154 requires a host system with a PCI Express clock that

complies with the PCI Express Specification. The NI-9154 may not

be compatible with systems using noncompliant clocks, particularly

clocks with peak frequencies higher than 100 MHz. For more

information about PCI Express clock compatibility with the NI-9154,

go to ni.com/info and enter the Info Code 915xclock.

■C Series I/O modules

■MXI-Express (x1) cable(s) up to 7 m long

■DIN rail mount kit (for DIN rail mounting only)

■ Panel mount kit (for panel mounting only)

■Three M4 or number 8 panhead screws (for mounting the chassis without

one of the listed mounting kits)

■Number 2 Phillips screwdriver

■Power supply

■ MXI-Express (x1) Series User Manual

Note Visit ni.com/info and enter the Info Code rdsowareversion to

determine which soware you need to use the NI-9154.

Installing C Series Modules

The following figure shows the mechanical dimensions of C Series I/O modules.

Figure 1. C Series I/O Module, Front and Side View with Dimensions

88.1 mm

(3.47 in.)

70.7 mm

(2.78 in.)

22.9 mm

(0.90 in.)

NI-9154 Getting Started

Complete the following steps to install a C Series I/O module in the chassis.

1. Make sure that no I/O-side power is connected to the I/O module. If the system

is in a nonhazardous location, the chassis power can be on when you install

I/O modules.

2. Align the I/O module with an I/O module slot in the chassis. The module slots

are labeled 1 to 8, le to right.

Figure 2. Installing an I/O Module in the Chassis

1. Insertion Groove

2. Latch

3. Squeeze the latches and insert the I/O module into the module slot.

4. Press firmly on the connector side of the I/O module until the latches lock the

I/O module into place.

5. Repeat these steps to install additional I/O modules.

Removing C Series Modules

Complete the following steps to remove a C Series I/O module from the chassis.

ni.com

NI-9154 Getting Started

1. Make sure that no I/O-side power is connected to the I/O module. If the system

is in a nonhazardous location, the chassis power can be on when you remove

I/O modules.

2. Squeeze the latches on both sides of the module and pull the module out of

the chassis.

Connecting the NI 9154 to Ground

You must connect the NI 9154 grounding terminal to the grounding electrode

system of the facility.

What to Use

■Ring lug

■Wire, 2.05 mm2 (12 AWG) or larger

■Screwdriver, Phillips #2

What to Do

Complete the following steps to ground the NI 9154.

1. Attach the ring lug to the wire.

2. Remove the grounding screw from the grounding terminal on the NI 9154.

3. Attach the ring lug to the grounding terminal.

4. Tighten the grounding screw to 0.5 N · m (4.4 lb · in.) of torque.

5. Attach the other end of the wire to the grounding electrode system of your

facility using a method that is appropriate for your application.

Caution If you use shielded cabling to connect to a C Series module with

a plastic connector, you must attach the cable shield to the chassis

grounding terminal using 1.3 mm diameter (16 AWG) or larger wire. Attach

a ring lug to the wire and attach the wire to the chassis grounding

NI-9154 Getting Started

terminal. Solder the other end of the wire to the cable shield. Use shorter

wire for better EMC performance.

For more information about ground connections, visit ni.com/info and enter the

Info Code emcground.

Connecting One or More NI-9154 Chassis to the MXI-Express

Host System or a Target

Complete the following steps to connect one or more NI-9154 chassis to a MXI-

Express host system or a target.

1. Make sure the MXI-Express host system is set up and configured as described

in the MXI-Express (x1) Series User Manual.

2. If the MXI-Express host system is powered up, power it down.

3. If the NI-9154 is powered up, power it down.

4. Use a MXI-Express (x1) cable to connect the MXI-Express host system to the

Upstream port of the first NI-9154 in the chain.

5. Use a MXI-Express (x1) cable to connect the Downstream port of the first

NI-9154 to the Upstream port of the next NI-9154 in the chain.

Note The maximum number of NI-9154 chassis in a chain depends

on the system configuration. For example, a PXI system with an NI

PXI-8196 controller can support four chassis per chain. Dierent

types of systems may support more or fewer chassis per chain. For

more information about how dierent system configurations can

aect the maximum number of chassis in a chain, go to ni.com/info

and enter the Info Code 915xchain.

6. Power up all of the connected NI-9154 chassis.

7. Power up the MXI-Express host system.

Note Refer to the MXI-Express (x1) Series User Manual for

connectivity options and supported host devices.

ni.com

NI-9154 Getting Started

Inhaltsverzeichnis

Andere NI Chassis Handbücher

NI NI-9157 Bedienungsanleitung

NI PXI Express PXIe-1082 Bedienungsanleitung

NI cRIO-9101 Bedienungsanleitung

NI cRIO-9082 Bedienungsanleitung

NI PXIe-1092DC Betriebsanleitung

NI PXI-1033 Bedienungsanleitung

NI PXIe-1090 Bedienungsanleitung

NI 9157 Bedienungsanleitung

NI PXI-1036 Bedienungsanleitung

NI 9144 Bedienungsanleitung

NI cRIO-FRC II Bedienungsanleitung

NI PXIe-1083 Bedienungsanleitung

NI cRIO-9082 Bedienungsanleitung

NI PXIe-1082DC Bedienungsanleitung

Beliebte Chassis Handbücher anderer Marken

Advantech

Advantech IPC-623 Series Bedienungsanleitung

IMC Networks

IMC Networks iMcV/18 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR665 V3 Bedienungsanleitung

Wuntronic

Wuntronic PCI4DRQ Bedienungsanleitung

EtherWAN

EtherWAN EMC400 Bedienungsanleitung

Overland Storage

Overland Storage SnapSAN S1000 Leitfaden

Philips

Philips LC4.1E A Bedienungsanleitung

Supermicro

Supermicro SCF418 Series Bedienungsanleitung

Chenbro

Chenbro RM437 Series Bedienungsanleitung

Pickering

Pickering 40-914 Bedienungsanleitung

HP A7503-S Montageanleitung

Supermicro

Supermicro SC823MTQ-R700LPB Bedienungsanleitung

SilverStone

SilverStone RMS08 Series Bedienungsanleitung

Pickering

Pickering 65-200 Bedienungsanleitung

Allied Telesis

Allied Telesis AT-MMCR18 Bedienungsanleitung

Hisense

Hisense MSD6586 Bedienungsanleitung

Cisco

Cisco Nexus 7010 Bedienungsanleitung

JYTEK

JYTEK PXIe-62780 Bedienungsanleitung