NI SCC-RLY01 Bedienungsanleitung

USER GUIDE

SCC-RLY01 Relay Module

The SCC-RLY01 contains one single-pole double-throw (SPDT)

nonlatching relay capable of switching 5 A at 30 VDC when using an

SC-2345 or SC-2350, or 250 VAC when using an SCC-68. Any single

E/M Series DAQ device digital input/output (P0) line 0 to 7 can control the

SCC-RLY01.

The SCC-RLY01 uses positive logic. A digital high sets the relay, and

a digital low resets it. In the set state, the common (COM) contact is

connected to the normally open (NO) contact. In the reset state, the

common (COM) contact is connected to the normally closed (NC) contact.

Conventions

The following conventions are used in this guide:

<> Angle brackets that contain numbers separated by an ellipsis represent

a range of values associated with a bit or signal name—for example,

P0 <3..0>.

»The »symbol leads you through nested menu items and dialog box options

to a final action. The sequence File»Page Setup»Options directs you to

pull down the File menu, select the Page Setup item, and select Options

from the last dialog box.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to

avoid injury, data loss, or a system crash. When this symbol is marked on

the product, refer to the Read Me First: Safety and Radio-Frequency

Interference document, shipped with the product, for precautions to take.

When symbol is marked on a product, it denotes a warning advising you to

take precautions to avoid electrical shock.

When symbol is marked on a product, it denotes a component that may be

hot. Touching this component may result in bodily injury.

SCC-RLY01 Relay Module User Guide 2 ni.com

bold Bold text denotes items that you must select or click in the software, such

as menu items and dialog box options. Bold text also denotes parameter

names.

italic Italic text denotes variables, emphasis, a cross-reference, or an introduction

to a key concept. Italic text also denotes text that is a placeholder for a word

or value that you must supply.

monospace Text in this font denotes text or characters that you should enter from the

keyboard, sections of code, programming examples, and syntax examples.

This font is also used for the proper names of disk drives, paths, directories,

programs, subprograms, subroutines, device names, functions, operations,

variables, filenames, and extensions.

SC-2345 SC-2345 refers to both the SC-2345 connector block and SC-2345 with

configurable connectors.

SCC SCC refers to any SCC Series signal-conditioning module.

What You Need to Get Started

To set up and use the SCC-RLY01, you need the following items:

❑Hardware

– SCC-68 orSC-2345 with one of the following:

• SCC-PWR01

• SCC-PWR02 and the PS01 power supply

• SCC-PWR03 (requires a 7 to 42 VDC power supply, not

included)

– One or more SCC-RLY01 modules

– 68-pin E/M Series DAQ device

– 68-pin cable

– Quick Reference Label

❑Software

– The latest version of NI-DAQmx

❑Documentation

–SCC-RLY01 Relay Module User Guide

–SC-2345/2350 User Manual or SCC-68 User Guide

–SCC Quick Start Guide

–Read Me First: Safety and Radio-Frequency Interference

©National Instruments Corporation 3 SCC-RLY01 Relay Module User Guide

– Documentation for your hardware

– Documentation for your software

❑Tools

– 1/8 in. flathead screwdriver

– Numbers 1 and 2 Phillips screwdrivers

– Wire insulation stripper

You can download NI documents from ni.com/manuals. To download

the latest version of NI-DAQ, click Download Software at ni.com.

Note Configuring the SCC system using Measurement & Automation Explorer (MAX) is

not supported on the Macintosh operating system.

Device Specific Information

Note For general SCC module installation and signal connection information, and

information about the SCC-68 or SC-2345 carrier, refer to the SCC Quick Start Guide,

available for download at ni.com/manuals.

Installing the Module

Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document

before removing equipment covers or connecting/disconnecting any signal wires.

Plug the SCC-RLY01 into any DIO socket J(X+9), where Xis 0 to 7, on the

SC-2345 or into any of the four slots that correspond to P0.0 to P0.3, on the

SCC-68.

Connecting the Input Signals

Note The signal names have changed. Refer to ni.com/info and enter rdtntg

to confirm the signal names.

Each screw terminal is labeled by pin number <1..3>. Pin 1 is the

NC terminal, pin 2 is the COM terminal, and pin 3 is the NO terminal.

The SCC-RLY01 contains one SPDT relay controlled by the digital line of

an E/M Series DAQ device P0. line X. The value of Xis determined by the

number of the DIO socket, J(X+9) on the SC-2345 or SCC Mod (X+ 1) on

the SCC-68, where you plug in the SCC-RLY01. Figure 1 shows a circuit

diagram of the SCC-RLY01.

SCC-RLY01 Relay Module User Guide 4 ni.com

Figure 1. SCC-RLY01 Circuit Diagram

Caution When connecting signals >60 VDC to the SCC-RLY01 module in the SCC-68,

you must use the high-voltage backshell. Figure 2 shows the high-voltage backshell.

Figure 2. High-Voltage Backshell

For information about how to configure the SCC-RLY01 module with

NI-DAQmx, refer to the SCC Quick Start Guide.

Specifications

These ratings are typical at 25 °C unless otherwise stated.

Electrical

Contact type............................................SPDT (Form C), nonlatching

Nominal switching capacity

SCC-68 ............................................5 A at 250 VAC

5 A at 30 VDC

SC-2345...........................................5 A at 30 VAC

5 A at 30 VDC

SCC-RLY01

E/M Series

COM

+5 V

P0.(X

)

D GND

390 Ω, 1/4 W

©National Instruments Corporation 5 SCC-RLY01 Relay Module User Guide

Caution The SCC-RLY01 module is derated to 30 V maximum switching voltage in the

SC-2345 carrier regardless of any other voltage markings found on the SCC-RLY01

module case.

Signal bandwidth.................................... DC to 400 Hz

Contact resistance .................................. 30 mΩmax

Switching time

Operate time (NC to NO)................ 5 ms (10 ms max)

Release time (NO to NC)................ 4 ms (5 ms max)1

Maximum operating speed..................... 30 cps at rated load

Contact lifetime...................................... 5 ×107operations at 180 cpm

(minimum)

Power Requirement

Digital power.......................................... 300 mW max

+5 V........................................................ 60 mA max

Physical

Figure 3. SCC-RLY01 Dimensions

Weight.................................................... 37 g (1.3 oz)

1 Excluding contact bounce time

1.87 cm

(0.74 in.) 7.93 cm

(3.12 in.)

3.55 cm

(1.4 in.)

SCC-RLY01 Relay Module User Guide 6 ni.com

I/O connectors.........................................One 20-pin right-angle

male connector

One 3-pin screw-terminal block

Field-wiring diameter .............................28 to 16 AWG

Maximum Working Voltage

Maximum working voltage refers to the signal voltage plus the

common-mode voltage.

When used with an SCC-2345

Channel-to-earth (inputs).................±60 VDC, Measurement

Category I

Caution Do not use for connection to signals in Measurement Category II, III, or IV. Do

not connect to MAINS.

When used with an SCC-68

Channel-to-earth (inputs).................±300 VDC, Measurement

Category II1

Caution Do not use for connection to signals in Measurement Category III, or IV.

Isolation Voltage

Channel-to-channel, channel-to-earth isolation

Continuous.......................................60 VDC,

Measurement Category I

Withstand.........................................2300 Vrms verified by a 5 s

dielectric withstand test

Environmental

Operating temperature ............................0 to 50 °C

Storage temperature ................................–20 to 65 °C

Humidity.................................................10 to 90% RH, noncondensing

1 For voltages >60 VDC, you must use the high-voltage backshell.

©National Instruments Corporation 7 SCC-RLY01 Relay Module User Guide

Maximum altitude .................................. 2,000 m

Pollution Degree (indoor use only) ........ 2

Safety

This product is designed to meet the requirements of the following

standards of safety for electrical equipment for measurement, control,

and laboratory use:

• IEC 61010-1, EN-61010-1

• UL 61010-1, CAN/CSA-C22.2 No. 61010-1

Note For UL and other safety certifications, refer to the product label or visit

ni.com/certification, search by model number or product line, and click the

appropriate link in the Certification column.

Electromagnetic Compatibility

This product is designed to meet the requirements of the following

standards of EMC for electrical equipment for measurement, control,

and laboratory use:

• EN 61326 EMC requirements; Minimum Immunity

• EN 55011 Emissions; Group 1, Class A

• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A

Note For EMC compliance, operate this device according to product documentation.

CE Compliance

This product meets the essential requirements of applicable European

Directives, as amended for CE marking, as follows:

• 73/23/EEC; Low-Voltage Directive (safety)

• 89/336/EEC; Electromagnetic Compatibility Directive (EMC)

Note Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit

ni.com/certification, search by model number or product line, and click the

appropriate link in the Certification column.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of their life cycle, all products must be sent to a WEEE recycling

center. For more information about WEEE recycling centers and National Instruments

WEEE initiatives, visit ni.com/environment/weee.htm.

SCC-RLY01 Relay Module User Guide 8 ni.com

SCC-RLY01 Module Pin Assignments

Figure 4 shows the I/O connector pins on the bottom of the module.

Figure 4. SCC Module Bottom View

Table 1 lists the signal connection corresponding to each pin. GND is the

reference for the +5 V supply.

1Pin1 2Pin2 3PWBKey 4Pin19 5 Pin 20

Table 1. SCC-RLY01 Pin Signal Connections

Pin Number Signal

1 —

2—

3 —

4 —

5 —

6 —

7P0.(X)

8 —

9+5 V

10 GND

11 —

12 —

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. Other product and company names mentioned herein are trademarks or trade

names of their respective companies. For patents covering National Instruments products, refer to the

appropriate location: Help»Patents in your software, the patents.txt file on your CD, or

ni.com/patents.

13 —

14 —

15 —

16 —

17 —

18 —

19 —

20 —

Table 1. SCC-RLY01 Pin Signal Connections (Continued)

Pin Number Signal

Inhaltsverzeichnis

Andere NI Steuereinheit Handbücher

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung