NI RTI-12308 Bedienungsanleitung

GETTING STARTED GUIDE

RTI-12308

Rear Transition Interface Generic DIO/AO/AI with MDR Headers

This document describes the features of the RTI-12308. You can use the RTI-12308 to connect

to any SLSC module supporting fully compatible rear I/O. The two 26-pin MDR connectors

provide access to up to 4 banks of signals for DIO, AI, or AO.

Note Before you begin, read the RTI-12308 Safety, Environmental, and Regulatory

Information document on ni.com/manuals and complete the software and hardware

installation procedures in your chassis documentation.

Installing the RTI-12308

Figure 1. Installing the RTI-12308 into the SLSC chassis

Caution Do not touch the contacts or remove the I/O boards or cables while the

system is energized.

Complete the following steps to install the RTI-12308 in the chassis.

1. Power off the main DC power source or disconnect it from the chassis before installing

any RTIs.

2. Ensure that the chassis is powered off.

The POWER LED should be off. If it is not off, do not proceed until it is off.

3. Loosen the screws of the upper rear panel of the chassis.

4. Position the RTI-12308 at the desired slot and insert the securing screws, but do not fully

tighten them.

5. Insert an SLSC module into the same slot as its corresponding RTI-12308 while firmly

holding the RTI-12308 in place until the RTI-12308 is firmly connected to the module.

6. Repeat steps 4 and 5 for all required RTIs.

7. Tighten the screws for all RTI-12308s and the screws of the upper rear panel of the

chassis.

This ensures proper alignment for future connections between modules and RTIs.

8. Tighten the two module mounting screws on each newly installed module.

Connecting JH1

To connect JH1, complete the following steps.

1. Prepare a terminal wire for JH1 by stripping insulation and installing a Molex Ultra-Fit™

crimp terminal following the manufacturer's specifications.

2. Insert a prepared terminal into an appropriate terminal socket of Molex Ultra-Fit™ 6-

position receptacle housing.

3. Repeat steps 1 and 2 for all appropriate terminals.

4. Insert a receptacle housing into JH1 until the plastic retention latch snaps into place.

JH1 is keyed to prevent reverse installation of the receptacle housing.

2| ni.com | RTI-12308 Getting Started Guide

RTI-12308 Pinout

Figure 2. RTI-12308 Front View

JR2, (Banks 1-2)

JR3, (Banks 3-4)

JH1

Figure 3. JH1 Pinout

V1+

V2+

V3+

V1-

V2-

V3-

RTI-12308 Getting Started Guide | © National Instruments Corporation | 3

Table 1. JH1 Connector Descriptions

JH1 Signal XP4 Contact JH1 Pin Description

V1+ F 6 Positive voltage for signal 1

V1- E 3 Negative voltage/Return for signal 1

V2+ D 5 Positive voltage for signal 2

V2- C 2 Negative voltage/Return for signal 2

V3+ B 4 Positive voltage for signal 3

V3- A 1 Negative voltage/Return for signal 3

Figure 4. User I/O Pinout

GND

Bank 2_5

Bank 2_4

GND

Bank 2_1

Bank 2_0

GND

Bank 1_5

Bank 1_4

GND

Bank 1_1

Bank 1_0

GND

Bank 2_7

Bank 2_6

GND

Bank 2_3

Bank 2_2

GND

Bank 1_7

Bank 1_6

GND

Bank 1_3

Bank 1_2

GND

Bank 4_5

Bank 4_4

GND

Bank 4_1

Bank 4_0

GND

Bank 3_5

Bank 3_4

GND

Bank 3_1

Bank 3_0

GND

Bank 4_7

Bank 4_6

GND

Bank 4_3

Bank 4_2

GND

Bank 3_7

Bank 3_6

GND

Bank 3_3

Bank 3_2

GND

JR2 JR3

Table 2. JR2 and JR3 Connector Signal Descriptions

Signal Description

Bank x_y Line y in Bank x

GND Ground connection

4| ni.com | RTI-12308 Getting Started Guide

Design Standards and Compatibility

SLSC Module Design Specifications

Version

1.6

RTI compatibility category Fully Compatible Rear I/O; Digital Input/

Output, Analog Input, or Analog Output up to

4 signal banks

Physical Characteristics

SLSC RTI slots 1

Dimensions 101.9 mm x 30.2 mm x 49.0 mm (4.01 in. x

1.19 in. x 1.93 in.)

Weight 49.0 g (1.7 oz)

Rear connectors

JH1 6-position Molex Ultra-Fit™, keyed white

(recommended mating connector—Molex

172258-4106; recommended crimp terminal—

Molex 172253-6011; recommended wire size

16 AWG - 18 AWG (UL 1061 or equivalent);

minimum wire temperature rating 80 °C;

minimum wire voltage rating 100V)

JR2 and JR3 26-position female MDR connectors

Connectors to SLSC module(s)

XP2 110-pin Hard Metric type A

XP4 6-blade Universal Power Module (UPM)

Product Certifications and Declarations

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance

information. To obtain product certifications and the DoC for NI products, visit ni.com/

product-certifications, search by model number, and click the appropriate link.

Worldwide Support and Services

The NI website is your complete resource for technical support. At ni.com/support, you have

access to everything from troubleshooting and application development self-help resources to

email and phone assistance from NI Application Engineers.

RTI-12308 Getting Started Guide | © National Instruments Corporation | 5

Visit ni.com/services for information about the services NI offers.

Visit ni.com/register to register your NI product. Product registration facilitates technical

support and ensures that you receive important information updates from NI.

NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,

78759-3504, USA. For up-to-date contact information for your location, visit ni.com/contact.

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for

information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their

respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your

software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find

information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer

to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how

to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS

TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

378335B-01 July 23, 2020

Inhaltsverzeichnis

Andere NI Aufnahmegeräte Handbücher

NI MXI-Express x1 Series Bedienungsanleitung

NI PCIe-8236 Bedienungsanleitung

NI TPC-2206 Bedienungsanleitung

NI RTI-12309 Betriebsanleitung

NI PXIe-6593 Bedienungsanleitung

NI VME-MXI-2 Bedienungsanleitung

NI PXIe-8245 Bedienungsanleitung

NI UMI-7764 Bedienungsanleitung

NI CompactRIO cRIO-9052 Bedienungsanleitung

NI PXIe-1487 Betriebsanleitung

Beliebte Aufnahmegeräte Handbücher anderer Marken

KV2 Audio

KV2 Audio 500 Series Bedienungsanleitung

Robotics Technologies

Robotics Technologies microBus-Cam II Bedienungsanleitung

Seca

Seca 460 Bedienungsanleitung

Cognex

Cognex MVS-8000 Series Bedienungsanleitung

Mect

Mect MPNC006 Series Bedienungsanleitung

Bad Caf

Bad Caf THE LEASH Bedienungsanleitung

Strymon

Strymon NIGHTSKY Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung

Tews Technologies

Tews Technologies TPMC465 Bedienungsanleitung

Honeywell

Honeywell Excel 50 Bedienungsanleitung

SeaLevel

SeaLevel COMM+8.LPCI Bedienungsanleitung

Arturia

Arturia AUDIOFUSE STUDIO Bedienungsanleitung

Rukra

Rukra RK-1240 Bedienungsanleitung

Samson

Samson SCOM Bedienungsanleitung

Dynacord

Dynacord DPS260 Bedienungsanleitung

Pyle Pro

Pyle Pro PSS8 Bedienungsanleitung

Nice

Nice Core Bedienungsanleitung

RF-System

RF-System TinyGate Gebrauchs- und Pflegehandbuch