Niagara 58145 Montageanleitung

Visit our website at: http://www.harborfreight.com

Email our technical support at: productsupport@harborfreight.com

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference. 21l

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools requir e d f o r a ssem b l y a nd ser v i c e may no t b e i n clud e d .

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 58145

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in serious injury.

Work Area

1. Keep your work area clean and well lit.

Cluttered dark areas invite accidents.

2. The work area should have adequate

drainage to reduce the possibility of

a fall due to slippery surfaces.

3. Keep bystanders, children, and visitors

away while operating the Sprayer.

Distractions can cause you to lose control.

Personal Safety

1. Follow all guidelines regarding

chemicals sprayed, including MSDS

instructions and EPA regulations.

2. Stay alert. Watch what you are doing and use

common sense when operating the Sprayer.

Do not use the Sprayer while tired or under

the influence of drugs, alcohol, or medication.

A moment of inattention while operating the

Sprayer may result in serious personal injury.

3. Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep your hair and

clothing away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

4. Do not overreach. Keep proper

footing and balance at all times.

Proper footing and balance enable better

control of the tool in unexpected situations.

5. Always wear eye protection.

Wear ANSI-approved safety goggles.

6. Always wear work gloves. Avoid skin

contact with bleach or bleach solution.

7. Wear a face mask when necessary. Avoid

inhaling fumes or vapors from bleach or

bleach solution.

Page 3For technical questions, please call 1-888-866-5797.Item 58145

Use

1. Use only for water or water-based fertilizers,

herbicides, pesticides, sealers, disinfectants,

or diluted bleach. Do not use to spray

combustible or undiluted corrosive chemicals.

2. Release pressure in Tank before removing

parts or storing tool. Contents are under

pressure and may spurt forcefully.

3. Only use in a well-ventilated area.

4. Do not point the Sprayer at yourself,

other people or animals.

5. Do not allow access to treated

areas by people or animals.

6. Industrial applications must follow

OSHA requirements.

7. Make sure the liquid used in the

Sprayer is not dirty or sandy.

8. This product is not a toy. Do not allow

children to play with or near this item.

9. Use as intended only.

10. Inspect before every use; do not use

if parts are loose or damaged.

11. Before filling, pull up on Pressure Release Valve to

ensure that it operates properly and does not stick.

12. Maintain product labels and nameplates.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

13. The warnings and cautions discussed in this

manual cannot cover all possible conditions

and situations that may occur. The operator

must understand that common sense and

caution are factors that cannot be built into this

product, but must be supplied by the operator.

Service

1. Have your Sprayer serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of

the tool is maintained.

2. Store idle tools and equipment out of

reach of children and other untrained

people. Tools and equipment are dangerous

in the hands of untrained users.

3. Maintain the Sprayer with care. Keep

this product clean. A properly maintained

Sprayer is easier to control.

SAVE THESE INSTRUCTIONS.

Specifications

Tank Capacity 1 gallon

Hose Length 41.5″

Wand Length 10.8″

Maximum Output 75 PSI

Bleach Ratio 1:99 or 1:49*

*Bleach containing 5.25% sodium hypochlorite

should be diluted as follows:

a. 1:99 diluted household bleach can be used for

general household cleaning. Mix 1/3 fl. oz.

(10 ml) of bleach with 34 fl. oz. (1 L) of water.

b. 1:49 diluted household bleach can be used to

disinfect surfaces contaminated with vomitus,

excreta, secretions or blood. Mix 1/3 fl. oz.

(10 ml) of bleach with 17 fl. oz. (.5 L) of water.

Make adjustments to the amount of bleach

added if its concentration of sodium

hypochlorite is above or below 5.25%.

Page 4 For technical questions, please call 1-888-866-5797. Item 58145

Components and Controls

Tank

Hose

Funnel

Top

Handle

Spray

Wand

Trigger

Handle

Nozzle

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before set up or use of this product.

1. Assemble Spray Wand:

a. Loosen Wand Nut, then slide Wand

into Trigger Handle Assembly.

b. Tighten Wand Nut securely.

Wand Trigger

Handle

Assembly

Wand

Nut

Nozzle

(not

shown)

Figure A: Spray Wand Assembly

Page 5For technical questions, please call 1-888-866-5797.Item 58145

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document

including all text under subheadings therein before set up or use of this product.

Inspect Sprayer before use, looking for damaged, loose, and missing parts.

If any problems are found, do not use Sprayer until repaired.

Follow all guidelines regarding chemicals sprayed, including MSDS instructions and EPA regulations.

Release pressure in Tank before loosening or removing parts.

Contents are under pressure and may spurt forcefully.

1. Make sure Handle is pushed all the way down into

Tank. Turn Handle Assembly counterclockwise to

loosen it. Pull the Handle Assembly out of the Tank.

2. Pour the liquid, through a strainer (sold

separately), into the Funnel Top.

Note: Do not use undiluted bleach with this sprayer.

Note: Fill the Tank no higher than max. fill line.

3. Replace Handle Assembly. Make sure Handle

is pushed all the way down into the Tank. Turn

Handle Assembly clockwise to tighten it securely.

4. Pump the Handle 20-30 times to build

sufficient pressure. Once the Sprayer is

pressurized (as indicated by increased tension

on the Handle), discontinue pumping.

5. Hold the Spray Wand Handle with the Nozzle

pointed away from you or any bystanders.

Press and hold the Trigger to begin spraying.

6. Twist the Nozzle to adjust the spray pattern.

7. For continuous spray, press the Trigger down

and forward until it locks, then release the

Trigger. To stop continuous spray, press

down and pull back on the Trigger.

Trigger

(Unlocked)

Trigger

(Locked)

8. As you continue to spray, the Sprayer will

depressurize. Release the Trigger to stop spraying.

Pump the handle 20-30 times to rebuild pressure.

9. When finished spraying:

• Depressurize the Tank.

• Dispose of liquid.

• Clean the Sprayer according to

Maintenance Instructions.

Note: To despressurize without spraying, carefully

turn the Handle Assembly counterclockwise. Lift

Handle Assembly slightly to depressurize contents.

Page 6 For technical questions, please call 1-888-866-5797. Item 58145

Inspection, Maintenance, and Cleaning

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

Do not use damaged equipment. If abnormal noise, vibration, or

leaking air occurs, have the problem corrected before further use.

Follow all guidelines regarding chemicals sprayed, including MSDS instructions and EPA regulations.

Release pressure in Tank by pulling up on the Pressure Release Valve before loosening

or removing parts. Contents are under pressure and may spurt forcefully.

1. BEFORE EACH USE, inspect the general

condition of the Sprayer. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts, and

• any other condition that may

affect its safe operation.

2. AFTER EVERY USE, Clean the Sprayer:

a. Flush with water.

b. Clean Nozzle and Filter (35).

c. Rinse with water and allow to air-dry.

3. PERIODICALLY, lubricate all moving parts of

the pump assembly with petroleum jelly.

4. Store the Sprayer in a safe, dry, clean location

out of reach of children and out of sunlight.

Troubleshooting

Problem Possible Causes Likely Solutions

Unit does not spray

1. Suction Tube (34) detached.

2. Not enough liquid in tank.

3. Handle Assembly loose.

4. Hose Nut (18) loose.

5. Safety Cap (22) loose.

6. Sprayer not pressurized.

7. Spray fluid contains

particles or sand.

8. Nozzle and/or Filter clogged

with mineral buildup.

1. Reattach Suction Tube.

2. Add liquid to tank.

3. Tighten Handle Assembly.

4. Tighten Hose Nut.

5. Tighten Safety Cap.

6. Pump Handle to pressurize Sprayer.

7. Disassemble, clean, then reassemble

Nozzle and/or Filter. Empty, clean, then

refill Tank with properly strained fluid.

8. Disassemble, clean, then reassemble

Nozzle and/or Filter.

Spray pattern is undesirable

1. Nozzle needs adjustment.

2. Spray fluid contains

particles or sand.

3. Nozzle and/or Filter clogged

with mineral buildup.

1. Adjust Nozzle.

2. Disassemble, clean, then reassemble

Nozzle and/or Filter. Empty, clean, then

refill Tank with properly strained fluid.

3. Disassemble, clean, then reassemble

Nozzle and/or Filter.

Follow all safety precautions whenever diagnosing or servicing the Sprayer.

Record Product’s Serial Number Here:

Note: If product has no serial number, record month

and year of purchase instead.

Note: Some parts are listed and shown

for illustration purposes only, and are not

available individually as replacement parts.

Specify UPC 193175432889 when ordering parts.

Page 7For technical questions, please call 1-888-866-5797.Item 58145

Parts List and Diagram

Part Description Qty

1 Nozzle 1

2 O-Ring 1

3 Diverter 1

4 Curved Connector 1

5 Wand Nut 2

6 Handle Connector 1

7 Handle Connector Nut 1

8 Seal 1

9 Piston Rod 1

10 O-Ring 1

11 O-Ring 1

12 Spring 1

13 Seal 1

14 Handle 1

15 Handle Nut 1

Part Description Qty

16 Hose 1

17 Wand 1

18 Trigger 1

19 Chock Plug 1

20 Outlet Tube 1

21 Outlet Filter 1

22 Outlet Nut 1

23 Tank 1

24 Pump Handle 1

25 O-Ring 1

26 Piston Cylinder 1

27 Bottom Stopper Plug 1

28 Piston Cylinder Nut 1

29 Piston Head 1

30 O-Ring 1

26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Inhaltsverzeichnis

Andere Niagara Spritzpistole Handbücher

Niagara

Niagara 56645 Montageanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Graco

Graco 246737 Gebrauchs- und Pflegehandbuch

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung