Nice TTDRGB Technische Daten

TTDRGB

LED control range

EN - Instructions and warnings for installation and use

2 – ENGLISH

ENGLISH

Translation of the original instructions in full

CONTENTS

GENERAL SAFETY WARNINGS AND

PRECAUTIONS

1 GENERALSAFETYWARNINGSANDPRECAUTIONS

a

WARNING! Important safety instructions. Observe all the

instructions as improper installation may cause serious

damages.

a

WARNING! Important safety instructions. It is important

to comply with these instructions to ensure personal

safety. Store these instructions carefully.

a

According to the latest European legislation, an automat-

ed device must be constructed in conformity to the har-

monised rules specied in the current Machinery Direc-

tive, which allow for declaring the presumed conformity

of the automation. Consequently, all the operations for

connecting the product to the mains electricity, its com-

missioning and maintenance must be carried out exclu-

sively by a qualied and expert technician.

a

In order to avoid any danger from inadvertent resetting

of the thermal cut-off device, this appliance must not be

powered through an external switching device, such as a

timer, or connected to a supply that is regularly powered

or switched off by the circuit.

WARNING! Please abide by the following warnings:

–Before commencing the installation, check the “Product techni-

cal specications”, in particular whether this product is suitable

for automating your guided part. Should it not be suitable, do

NOT proceed with the installation.

–The product cannot be used before it has been commissioned

as specied in the “Testing and commissioning” chapter.

–Before proceeding with the product’s installation, check that all

the materials are in good working order and suited to the intend-

ed applications.

–The product is not intended for use by persons (including chil-

dren) with reduced physical, sensory or mental capacities, nor

by anyone lacking sufcient experience or familiarity with the

product.

–Children must not play with the appliance.

–Do not allow children to play with the product’s control devices.

Keep the remote controls out of reach of children.

–The system’s power supply network must include a disconnec-

tion device (not supplied) with a contact opening gap permit-

ting complete disconnection under the conditions envisaged by

Overvoltage Category III.

–Handle the product with care during installation, taking care to

avoid crushing, denting or dropping it, or allowing contact with

liquids of any kind. Keep the product away from sources of heat

and naked ames. Failure to observe the above can damage the

product, and increase the risk of danger or malfunction. Should

this happen, stop installation immediately and contact Custom-

er Service.

–The manufacturer declines all liability for damages to property,

objects or people resulting from failure to observe the assem-

bly instructions. In such cases, the warranty for material defects

shall not apply.

1 GENERAL SAFETY WARNINGS AND PRECAUTIONS . . . . . 2

2 PRODUCT DESCRIPTION AND INTENDED USE . . . . . . . . . 3

2.1 List of constituent parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1 Pre-installation checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3.2 Product usage limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3.3 Product identification and overall dimensions . . . . . . . . . . . . . . . . . .3

3.4 Product installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4 ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . 4

4.1 Preliminary checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4.2 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

5 PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5.1 TWO-WAY and ONE-WAY operation . . . . . . . . . . . . . . . . . . . . . . . . .4

5.2 Transmitter pairings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

5.2.1 Memorising the FIRST TRANSMITTER. . . . . . . . . . . . . . . . . . . . .5

5.2.2 MEMORISING AN ADDITIONAL TRANSMITTER . . . . . . . . . . . . .5

5.3 LOCKING AND UNLOCKING THE MEMORY . . . . . . . . . . . . . . . . . .7

5.4 DELETION PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

5.4.1 DELETION procedures (with MEMORISED transmitter) . . . . . . . .7

5.4.2 DELETION procedures (with NON-MEMORISED transmitter in

ONE-WAY mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

5.4.3 Pre-defined (PRESET) or personalised (CUSTOM) colours . . . . . .8

5.4.4 Rotation speed of the RGB colours . . . . . . . . . . . . . . . . . . . . . . .9

6 COMMANDS FROM THE TRANSMITTER . . . . . . . . . . . . . . . 9

7 TESTING AND COMMISSIONING. . . . . . . . . . . . . . . . . . . . . . 9

8 PRODUCT MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . 10

9 PRODUCT DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

10 TECHNICAL SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . 10

10.1 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

10.2 Suggested power supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

11 CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ENGLISH – 3

–Cleaning and maintenance reserved for the user must not be

carried out by unsupervised children.

–Before intervening on the system (maintenance, cleaning), al-

ways disconnect the product from the mains power supply and

from any batteries.

–Check the system frequently.

–The packing materials of the product must be disposed of in

compliance with local regulations.

–Before connecting the power supply unit to the mains, make

sure that the LEDs are properly connected to the receiver.

–Incorrect connection of the LED diodes (reversed polarity) could

damage them, therefore be very careful to position the poles

correctly when connecting them.

–When it is switched on, the receiver resumes the same condition

prior to being switched off.

–The product must not be incorporated or installed in insulating

products such as mineral wool or polystyrene, or similar prod-

ucts.

PRODUCT DESCRIPTION AND INTENDED

USE

2 PRODUCTDESCRIPTIONANDINTENDEDUSE

Led Control Range TTDRGB is a “dimmer” combined with a radio re-

ceiver that is used to control RGB (Red-Green-Blue) LEDs. For it to work,

it must be powered by a 24 VDC external power supply unit (not supplied).

Through a paired transmitter it is possible to set the programmes. The

LEDs are controlled exclusively via radio through the paired transmitters.

a

CAUTION! – Any use other than that specied herein or in

environmental conditions other than those stated in this

manual is to be considered improper and is strictly for-

bidden!

2.1 LIST OF CONSTITUENT PARTS

The TTDRGB is made up of a casing that protects the command and

control boards. “Figure 1” shows the main parts making up the TTDRGB.

A Connection to the LED strips

B Connection to the 24Vdc power supply unit

INSTALLATION

3 INSTALLATION

3.1 PRE-INSTALLATION CHECKS

Before proceeding with the product’s installation, it is necessary to:

–check the integrity of the supply

–check that all the materials are in good working order and suited to the

intended use

–check that all operating conditions comply with that specied in the “

Product usage limits” paragraph and in the “TECHNICAL SPECIFI-

CATIONS” chapter

–check that the chosen installation location is compatible with the prod-

uct’s overall dimensions (see “Figure 2”)

–check that the surface chosen for installing the product is solid and can

ensure stable attachment

–make sure that the installation area is not subject to ooding; if neces-

sary, the product must be installed appropriately raised above ground

level

–check that the space around the product allows safe and easy access.

3.2 PRODUCT USAGE LIMITS

The product can be used exclusively with 24Vdc power supply units

and with 24 V LED strips of adequate power (refer to the “TECHNICAL

SPECIFICATIONS” chapter).

3.3 PRODUCT IDENTIFICATION AND OVERALL

DIMENSIONS

The overall dimensions and label (A) that allow for identifying the product

are shown in “Figure 2”.

98 mm

26 mm

20 mm

Tc point

4 – ENGLISH

3.4 PRODUCT INSTALLATION

To fasten TTDRGB (“Figure 3”):

1. position the box (A) and fasten it with bi-adhesive tape (B) (not

supplied)

2. make the electrical connections by operating as described in the

“ELECTRICAL CONNECTIONS” chapter.

ELECTRICAL CONNECTIONS

4 ELECTRICALCONNECTIONS

4.1 PRELIMINARY CHECKS

f

All electrical connections must be made with the sys-

tem disconnected from the mains electricity and with the

emergency power supply (if present in the automation)

disconnected.

a

The connection operations must only be carried out by

qualied personnel.

f

Mount a device on the electric power line that completely

disconnects the automation from the grid.

–The disconnection device must have contacts with a sufcient

gap to ensure complete disconnection, under the Category III

overvoltage conditions, in accordance with the installation in-

structions. If necessary, this device guarantees quick and safe

disconnection from the mains power and therefore must be

positioned in sight of the automation. If located in a concealed

position, it must be equipped with a system that prevents inad-

vertent or unauthorised reconnection of power, to avoid poten-

tial hazards.

4.2 ELECTRICAL CONNECTIONS

To make the electrical connections:

–connect the cable (A) to the chosen 24Vdc power supply unit

–connect the connector (B) to the LED strips.

Table 1

OUTPUTS TOWARDS LED STRIPS

PIN Exit RGB

1OUT 3 Blue

2OUT 1 Red

3OUT 2 Green

4Common (+)

l

For connecting multiple LED strips, make sure you use

suitable cables and adapters compatible with the con-

nector (B).

PROGRAMMING

5 PROGRAMMING

5.1 TWO-WAY AND ONE-WAY OPERATION

The Led Control Range can operate with both TWO-WAY and ONE-

WAY transmission. The transmission mode is determined by the rst trans-

mitter (ONE-WAY or TWO-WAY) paired with the system.

l

WARNING: if the system is new (has no transmitter mem-

orised), when it is switched on the paired LED strip will

emit a ash. Run one of the memorisation procedures for

the rst transmitter described in the paragraph “Memo-

rising the FIRST TRANSMITTER”. If the paired LED strip

does not emit any ash when the system is switched on,

it means that at least one memorised transmitter is al-

ready present.

OFF

ERA

NEW ON

BiDi

MONO

(x 1)

ENGLISH – 5

5.2 TRANSMITTER PAIRINGS

The functions and programming modes described below must be made

with a transmitter paired (memorised) with the system.

5.2.1 MEMORISING THE FIRST TRANSMITTER

5.2.1.1 TWO-WAY mode

RAPID PROCEDURE (only for memorising the rst transmitter)

To memorise the rst transmitter (“Figure 6”):

1. disconnect the power supply to the system. Wait 5 s. Power the

system again. One ash of the LED strips indicates that the system

has no paired transmitter

2. within 10 s from the power-up, simultaneously press pand qfor

3 s on the transmitter to be paired. Three ashes of the LED strips,

relative to the chosen channel, will conrm the correct pairing.

OFF ON

5sec

2End

(= 3s)

(x 1)

(x 3)

NORMAL PROCEDURE

To memorise the rst transmitter (“Figure 7”):

1. disconnect the power supply to the system. Wait 5 s. Power the

system again. One ash of the LED strips indicates that the system

has no paired transmitter

2. within 10 s from the power-up, press PRG for 5 s on the transmitter

to be paired. Over the next 2 minutes, all LED systems within the

radio range will start ashing, each for a random duration

3. choose the LED system involved in the programming and, with the

LED lit, press and release the p key (once)

4. in the LED system involved, with the LED lit, press and release the

q key (once)

5. the LED strip will ash three times to conrm the memorisation.

OFF ON

5sec

1 2 3

(= ON)

(= 5s)

PRG PRG

(x 1)

4End

(= ON)(x 3)

(x 1)

5.2.1.2 ONE-WAY mode

To memorise the rst transmitter (“Figure 8”):

1. disconnect the power supply to the system. Wait 5 s. Power the

system again. One ash of the LED strips indicates that the system

has no paired transmitter

2. within 10 s from the power-up, press ofor 3 s on the transmitter

to be paired. Three ashes of the LED strips, relative to the chosen

channel, will conrm the correct pairing.

OFF ON

5sec

2End

(= 3s)

(x 1)

(x 3)

5.2.2 MEMORISING AN ADDITIONAL TRANSMITTER

To perform the procedure described below, it is necessary to have a new

transmitter to memorise and an old previously memorised transmitter. The

two transmitters must have the “PRG” and “ESC” keys (such as, for exam-

ple, “ERA P” and “ERA W” series transmitters). The procedure memorises

all the keys of the new transmitter, in “Mode I”, replicating the same con-

guration of the old transmitter.

5.2.2.1 TWO-WAY mode

The system, congured to operate in TWO-WAY mode, can memorise up

to 30 transmitters.

6 – ENGLISH

To memorise the transmitter (“Figure 9”):

1. on the OLD transmitter: press and release the PRG key. The LED

strip will ash twice

2. on the NEW transmitter: press and hold the STOP key for 5 s

then release it. The LED strip will ash twice

3. on the OLD transmitter: press and release the PRG key. The LED

strip will ash twice

4. on the NEW transmitter: press and release the STOP key. The

LED strip will ash three times to conrm the memorisation.

(x 1)

(x 2)

OLD PRG

(x 2)

OLD PRG

(x 2)

NEW

5sec

3 4

NEW

(x 1)

(x 3)

(x 1)

End

5.2.2.2 ONE-WAY mode and transmitters having the “PRG”

and “ESC” keys

The system, congured to operate in ONE-WAY mode, can memorise up

to 30 transmitters.

To memorise the transmitter (“Figure 10”):

1. on the OLD transmitter: press and hold the PRG key. The LED

strip will ash twice and, after a brief pause, will emit two more

ashes. Release the PRG key

2. on the NEW transmitter: press and hold the PRG key for 7 s. The

LED strip will ash twice. Release the PRG key

3. on the OLD transmitter: press and release the PRG key. The LED

strip will ash three times to conrm the memorisation.

OLD

NEW

(x 2)

...

PRG

(x 2)

7sec (x 2)

3End

(x 1)

(x 3)

OLD PRG

5.2.2.3 ONE-WAY mode and transmitters lacking the “PRG”

and “ESC” keys

To memorise the transmitter (“Figure 11”):

1. on the NEW transmitter: press the okey for 7 s

2. on the OLD transmitter: press the okey 3 times

3. on the NEW transmitter: press the okey for 3 s. The LED strip

will ash three times to conrm the memorisation.

OLD

(x 3)

3End

NEW

7sec

(x 3)

NEW

3sec

ENGLISH – 7

5.3 LOCKING AND UNLOCKING THE MEMORY

Activating the memory lock allows for preventing the accidental and ran-

dom memorisation of other unintended or unauthorised transmitters.

To do this (“Figure 12”):

1. press PRG once on the transmitter. The paired LED strip will ash

twice

2. press PRG once on the transmitter. The paired LED strip will ash

twice

3. press PRG once on the transmitter. The paired LED strip will ash

three times

4. simultaneously press pand qfor 5 s. The paired LED strip will

ash four times. Release the buttons

–to LOCK the memory press p for 5 s. The paired LED strip will ash

three times

–to UNLOCK the memory press p for 5 s. The paired LED strip will ash

ve times.

3 4

(x 1)

PRG

5a / 5b

5 a End

x 3

1 2

(x 1)

PRG

x 2

(x 1)

PRG

x 2

(= 5s)

x 5

(= 5s)

5 b End

(= 5s)

x 4

5.4 DELETION PROCEDURES

a

The deletion procedures are irreversible. The deletion

of one or more remote controls eliminates the settings

memorised in the system relative to the remote controls

themselves. The FULL deletion procedure restores the

system’s factory conditions. At the end of the procedure,

all settings previously memorised will be lost.

5.4.1 DELETION PROCEDURES (WITH MEMORISED

TRANSMITTER)

RAPID PROCEDURE (only for deleting ALL SETTINGS)

To do this (“Figure 13”):

1. disconnect the power supply to the system. Wait 5 s. Power the

system again

2. within 10 s from the power-up, press pand qfor 3 s. The paired

LED strip will ash ve times to conrm the deletion.

1 2 End

OFF ON

5sec

x 5

(= 3s)

NORMAL PROCEDURE

To do this (“Figure 14”):

1. press PRG once on the transmitter. The paired LED strip will ash

twice

2. press PRG once on the transmitter. The paired LED strip will ash

twice

3. press PRG once on the transmitter. The paired LED strip will ash

three times

4. press PRG once on the transmitter. The paired LED strip will ash

four times

5. press the keys indicated in “Table 2” to select the desired option

among those available. At the end of the procedure, the paired LED

strip will ash three or ve times to conrm the deletion.

1 2

(x 1)

PRG

x 2

(x 1)

PRG

x 2

3 4 5

(x 1)

PRG

x 3

(x 1)

PRG

x 4

(... see

the table

and press

the keys)

End

Table 2

DELETION

Buttons Setting

px 3 s

Deletion of a SINGLE REMOTE CONTROL:

after selecting this option, press oon the

remote control to be eliminated to complete the

procedure. The paired LED strip will ash ve

times

p+ qx 3 s Deletion of ALL SETTINGS

ox 3 s Deletion of ALL REMOTE CONTROLS

PRG FULL deletion (reset to the system’s factory

settings)

8 – ENGLISH

5.4.2 DELETION PROCEDURES (WITH NON-MEMORISED

TRANSMITTER IN ONE-WAY MODE)

l

In TWO-WAY mode, follow the procedure indicated in

the paragraph “Memorising the FIRST TRANSMITTER”,

sub-paragraph “TWO-WAY mode”.

To do this (“Figure 15”):

1. disconnect the power supply to the system. Wait 5 s. Power the

system again

2. within 10 s from the power-up, press ofor 5 s on the non-memo-

rised transmitter. The paired LED strip will emit two or three ashes

3. disconnect the power supply to the system. Wait 5 s. Power the

system again

4. press PRG once on the transmitter. The paired LED strip will ash

twice

5. press PRG once on the transmitter. The paired LED strip will ash

twice

6. press PRG once on the transmitter. The paired LED strip will ash

three times

7. press PRG once on the transmitter. The paired LED strip will ash

four times

8. press the keys indicated in “Table 3” to select the desired option

among those available. At the end of the procedure, the paired LED

strip will ash three or ve times to conrm the deletion.

OFF ON

5sec

OFF ON

5sec

3 4

NEW x 2

(= 5s)

PRG

6 7 8

(x 1)

PRG

x 3

(x 1)

PRG

x 4

(... see

the table

and press

the keys)

End

(x 1)

x 2PRG

(x 1)

x 2

Table 3

DELETION

Buttons Setting

px 3 s

Deletion of a SINGLE REMOTE CONTROL:

after selecting this option, press oon the

remote control to be eliminated to complete the

procedure

p+ qx 3 s Deletion of ALL SETTINGS

ox 3 s Deletion of ALL REMOTE CONTROLS

PRG FULL deletion (reset to the system’s factory

settings)

5.4.3 PRE-DEFINED (PRESET) OR PERSONALISED (CUSTOM)

COLOURS

The system leaves the factory (PRESET) with 8 pre-congured and avail-

able colours. Activating the “CUSTOM” function allows for memorising

personalised colours which can then be recalled.

l

After enabling the “CUSTOM” function, the personalised

intensity must be set using a memorised transmitter, as

explained in the “COMMANDS FROM THE TRANSMIT-

TER” chapter.

l

If the colours/intensities are set through the PRESET

function, refer to “Table 6”. If CUSTOM colours/intensi-

ties are set, refer to “Table 7”.

5.4.3.1 Setting through memorised transmitters

To activate the “PRESET/CUSTOM” function (“Figure 16”):

1. press PRG once on the transmitter. The paired LED strip will ash

twice

2. press PRG once on the transmitter. The paired LED strip will ash

twice

3. press o for 3 s. The paired LED strip will ash twice. Release o

4. press pfor 3 s or qfor 3 s to select the desired option among

those available in “Table 4”. If the pkey is pressed, the paired LED

strip will ash three times, while if the qkey is pressed the LED strip

will ash four times. Release the pressed key.

1 32

x 3

(x 4)

PRG

4End

( )

(>3s)

x 2x 2

(x 1)

PRG

x 2

(x 1) (>3s)

Table 4

PRE-DEFINED (PRESET) OR PERSONALISED (CUSTOM) COLOURS/

INTENSITIES

Buttons Setting

px 3 s

PRE-SET colours (factory setting):

8 xed pre-set colours – red, green,

blue, hot/cold white, cyan, yellow,

magenta.

qx 3 s CUSTOM colours: customisable by

the user (factory setting: blue).

ENGLISH – 9

5.4.4 ROTATION SPEED OF THE RGB COLOURS

This function allows for varying the rotation speed of the RGB LED strip

colours. To activate rotation of the colours, refer to the “COMMANDS

FROM THE TRANSMITTER” chapter.

5.4.4.1 Setting through memorised transmitters

To do this (“Figure 17”):

1. press PRG once on the transmitter. The paired LED strip will ash

twice

2. press PRG once on the transmitter. The paired LED strip will ash

twice

3. press q for 3 s. The paired LED strip will ash three times. Release

4. press q (several rimes) until you select the desired option among

those available in “Table 5”. The paired LED strip will show the

selected behaviour after a short while

5. press o for 3 s to conrm the choice and exit the function. The

paired LED strip will ash three times. Release o.

3 4 5

5End

x 3

(3s) x 3

1 2

(x 1)

PRG

x 2

(x 1)

PRG

x 2

(x ...)(= 3s)

... (x ...)

Table 5

ROTATION SPEED OF THE RGB COLOURS

No. of button presses Setting

q(x 1) Speed 1 RGB (factory setting: 4

s - 1 s)

q(x 2) Speed 2 RGB (16 s - 6 s)

q(x 3) Speed 3 RGB (28 s - 10 s)

COMMANDS FROM THE TRANSMITTER

6 COMMANDSFROMTHETRANSMITTER

The table shown below summarises the keys to be pressed on the trans-

mitter for sending the main commands to the system.

Table 6

COMMANDS FROM THE TRANSMITTER WITH SETTING OF PRE-DEFINED

COLOURS (PRESET)

Buttons Channel activated

p(x 1) Lighting up at the last colour set

p(> 1 s) Increase of the light intensity

o- Stops rotation if colour rotation is under way

- Colour selection

q(> 1 s) Decrease of the light intensity

q(x 1) Switch-off

o+ pClockwise colour rotation

o+ qAnti-clockwise colour rotation

SLIDER + Increase of the light intensity

SLIDER - Decrease of the light intensity

Table 7

COMMANDS FROM THE TRANSMITTER WITH SETTING OF PERSONALISED

COLOURS (CUSTOM)

Buttons Channel activated

p(x 1) Lighting up at the custom colour for that channel

p(> 1 s) Increase of the light intensity

- Stops rotation if colour rotation is under way

- Selection of the personalised colour for that channel

- Anti-clockwise rotation of the colours if no

personalised colour has been set for that channel

q(> 1 s) Decrease of the light intensity

q(x 1)

- Switching off if the command arrives from the same

channel

- If the command arrives from another channel it

switches it on

o+ pClockwise colour rotation

o+ qAnti-clockwise colour rotation

p+ qSaving of the “custom” colour (the LED strip will ash

three times to conrm the memorisation)

SLIDER + Increase of the light intensity

SLIDER - Decrease of the light intensity

TESTING AND COMMISSIONING

7 TESTINGANDCOMMISSIONING

These are the most important phases of the automation set-up for max-

imising the system’s safety. The testing procedure can also be used to

periodically check the devices making up the system.

The sequence of steps to be performed when running the testing phase,

as described below, refers to a typical system.

To run the test:

1. verify that all the instructions stated in the “GENERAL SAFETY

WARNINGS AND PRECAUTIONS” chapter have been strictly

observed

2. using the control devices (transmitter), switch the LED strips on and

off to test them and verify that they behave according to their set

programme.

10 – ENGLISH

a

Commissioning can only be performed after all testing

phases have been successfully completed.

a

Before commissioning the system, ensure that the owner

is properly informed of all residual risks and hazards.

PRODUCT MAINTENANCE

8 PRODUCTMAINTENANCE

TTDRGB the electronic part does not require any special maintenance.

In any case, every 6 months the system should be checked to ensure the

entire system is working efciently.

PRODUCT DISPOSAL

9 PRODUCTDISPOSAL

l

This product is an integral part of the operator and must

therefore be disposed of with it.

As with the installation, only qualied personnel must dismantle the prod-

uct at the end of its life.

This product is composed of different types of materials. Some of these

materials can be recycled; others must be disposed of. Please enquire

about the recycling or disposal systems in place in your local area for this

type of product.

l

As indicated by the symbol shown

here, this product must not been

disposed of with household waste.

Separate the waste for disposal and

recycling, following the methods stip-

ulated by local regulations, or return

the product to the seller when pur-

chasing a new product.

a

WARNING

Some parts of the product may contain polluting or dan-

gerous substances. If not disposed of correctly, these

substances may have a damaging effect on the environ-

ment and human health.

a

WARNING

Local regulations may impose heavy penalties if this

product is not disposed of in compliance with the law.

TECHNICAL SPECIFICATIONS

10 TECHNICALSPECIFICATIONS

10.1 TECHNICAL SPECIFICATIONS

l

All technical specications stated in this section refer

to an ambient temperature of 20°C (± 5°C). Nice S.p.A.

reserves the right to apply modications to the product

at any time when deemed necessary, without altering its

functions and intended use.

Table 8

TECHNICAL SPECIFICATIONS

Description Technical specication

Power supply 24 Vdc (+/-10%)

Outputs 1 (RGB) x 24 Vdc (+/-5%)

Total maximum power See product label

Maximum output power 100W

Operating temperature -20°C ÷ +45°C

Reception frequency 433.92 MHz

Radio memory capacity (transmitters) 30

Protection rating IP55

Dimensions (L x D x H) 98 x 26 x 20 mm

l

The connecting cables must have an adequate cross-sec-

tional size for the maximum load applied. The output ca-

ble of the LED strips must not be longer than 2 m, in ac-

cordance with the EMC standard.

10.2 SUGGESTED POWER SUPPLY UNIT

Below are the characteristics of a power supply unit we suggest using:

–use a SELV LED control gear with constant voltage, certied according

to the IEC/EN 61347-2-13 standard, protected against short circuits.

Maximum power 240 W (Prated max 240 W).

CONFORMITY

11 CONFORMITY

SIMPLIFIED EU DECLARATION OF CONFORMITY

The manufacturer, Nice S.p.A., declares that the product LED CONTROL

RANGE is compliant with the directive 2014/53/UE.

The full text of the EU declaration of conformity is available at the following

internet address: https://www.niceforyou.com/en/support.

Inhaltsverzeichnis

Andere Nice Beleuchtungsausrüstung Handbücher

Nice

Nice LLW Technische Daten

Nice

Nice TTDW Technische Daten

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung